Subscribe to Our Youtube Channel
Related Manuals for Goodway BioSpray-10C
Summary of Contents for Goodway BioSpray-10C
- Page 1 BioSpray®-10C Surface Sanitation System Operating and Maintenance Instructions Read before operating.
-
Page 2: Table Of Contents
PARTS BREAKDOWN (BIOSPRAY®-10C) ................. 10-11 Thank you for purchasing this Goodway Surface Sanitization System. We appreciate your business and look forward to serving you in the future. As with all Goodway products, you can be assured that the finest quality components and workmanship have gone into this machine. -
Page 3: General
Do not operate without eye protection or other necessary protective gear. Consult SDS for all chemicals and for CO OSHA exposure limits. Consult Goodway or chemical manufacturer about mixing or using unspecified chemicals with this unit. Service must be performed by qualified personnel. -
Page 4: Identifying Main Parts
IDENTIFYING MAIN PARTS (BioSpray®-10C) Spray Gun Regulator Spray Gun Tank Pressure Gauge Pressure Gauge Coil Hose Front Stand Outlet Connector Rear Door Wheels BIOSPRAY®-10C 1020... -
Page 5: Installation/Setup
INSTALLATION/SETUP 1. Remove from packaging and inspect unit. If anything is damaged, contact Goodway Technologies immediately (800-333-7467). 2. Place the surface sanitization system on a flat surface. Installing the CO Tank (BioSpray®-10C): 1. Open the rear door 2. Detach and loosen both straps that will hold in the 10 lb. -
Page 6: Operating Instructions
OPERATING INSTRUCTIONS Attach Goodway approved formula to spray gun. NOTE: To do this, carefully remove the foil seal on the top of the bottle, making sure that no debris gets into the bottle, as that will impede the spraying. Be careful not to overtighten the bottle, it only has to be snug to seal. -
Page 7: Increasing The Pressure
INCREASING THE PRESSURE: When increasing the pressure of this BioSpray® unit, be aware of the following: The pressure may need to be increased for spraying longer distances or for the removal of bio-burdens. The standard PSI rating for operation is 24-26 PSI while spraying. After intermittent use at higher pressure, the regulator should be reset to 24-26 PSI. -
Page 8: Other Operating Information
WARNING: Use only 10 lb. (BioSpray®-10C) preferably aluminum tank with a 7” diameter. If a spare tank is needed, please call Goodway Technologies at (800) 333-7467 toll-free or email us at goodway@goodway.com. Do not use any CO tank with a dip tube. -
Page 9: Technical Information
Damage to spray Check both parts to be noise gun or coil hose sure where the damage has occurred. Contact Goodway Technologies to acquire the proper replacement parts. Regulator frozen Wait for the regulator or damaged to get back to room temperature, then continue use. -
Page 10: Parts Breakdown (Biospray®-10C)
PARTS BREAKDOWN (BioSpray®-10C) PARTS NUMBER (BioSpray®-10C) Part Number Description SANI-091 Cover SANI-096 Bottle Holder SANI-100 Bottle Stop SANI-014 0-160 PSI Pressure Gauge, Regulator SANI-015 0-2000 PSI Pressure Gauge, Tank Handle Hook 9672 Door Hook SANI-092 Rear Door SANI-009 Latch, Rear Door 6226 Wheel SANI-101... - Page 11 NOTES BIOSPRAY®-10C 1020...
- Page 12 Visit: www.goodway.com P/N: MNL-BIOSPRAY-10C ©Copyright 2020 Goodway Technologies Corp., Stamford, CT USA Effective date October 6, 2020 Goodway is a Trademark of Crossford International. Goodway reserves the right to improve products; contact the factory for the latest configuration and uses.
Need help?
Do you have a question about the BioSpray-10C and is the answer not in the manual?
Questions and answers