Tekmar tekmarNet 541 Wiring Brochure
  1. Manuals
  2. Brands
  3. Tekmar Manuals
  4. Thermostat
  5. 541
  6. Wiring brochure
Tekmar tekmarNet 541 Wiring Brochure

Tekmar tekmarNet 541 Wiring Brochure

Hide thumbs Also See for tekmarNet 541:
1
2
3
4
5
6
7
8
Table of Contents

Advertisement

Quick Links

Download this manual
- Wiring Brochure
®
tekmarNet
4 Thermostat 541
1
2
Information
Application
Brochure
Choose controls
Design your
to match
mechanical
application
applications
Overview
The following brochure describes how to wire the tekmar tekmarNet
heat stage. The 541 has inputs for one auxiliary sensor. The wiring of 541 thermostat is simple and cost effective.

Table of Contents:

Definitions .......................................................................2
Rough-In Wiring .............................................................2
Remove the Wiring Cover ..............................................3
Mounting the Thermostat ...............................................3
Wiring Symbols ...............................................................3
3
Layout
Brochure
Brochure
Rough-in
wiring
instructions
4
Wiring
Brochure
Wiring and
installation of
specific control
®
4 (tN4) thermostat 541. The 541 has outputs for one
Auxiliary
Sensor
To isolate relay,
cut jumper
tN4
Network
24 V (ac)
Power
Electrical Drawings ......................................................3-5
Wiring the Thermostat ....................................................6
Troubleshooting the Wiring .............................................7
Testing the Wiring ...........................................................7
Technical Data ................................................................8
1 of 8
5
6
Data
Brochure
Control settings
Record settings &
and sequence of
operation
DIP
Switches
1st Stage
Heating
© 2005
W 541
06/05
Job
Record
wiring details for
future reference
W 541 - 06/05

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the tekmarNet 541 and is the answer not in the manual?

Questions and answers

Related Manuals for Tekmar tekmarNet 541

Summary of Contents for Tekmar tekmarNet 541

  • Page 1: Table Of Contents

    Overview The following brochure describes how to wire the tekmar tekmarNet ® 4 (tN4) thermostat 541. The 541 has outputs for one heat stage. The 541 has inputs for one auxiliary sensor. The wiring of 541 thermostat is simple and cost effective.

  • Page 2: Definitions

    Defi nitions The following defined terms and symbols are used throughout this manual to bring attention to the presence of hazards of various risk levels, or to important information concerning the life of the product. – Caution: Refer to accompanying documents. –...

  • Page 3: Remove The Wiring Cover

    Remove the Wiring Cover: Push tab To remove the wiring cover: Remove cover • Place a small slot screwdriver or similar tool into the slot located on the top of the thermostat. • While pushing against the plastic tab, pull the top of the front cover so that it pivots around the bottom edge of the thermostat’s base.
  • Page 4 Electrical Application 541 E1 Description: One Stage Heating (H1 = Radiant). Legend: Sensor 1 = Floor Slab Sensor 541 tNt To isolate relay, cut jumper Factory installed jumper connects R to Rh (terminals 3 to 4) To isolate W relay, Zone Managers cut jumper ©...
  • Page 5 Electrical Application 541 E2 Description: One Stage Heating (H1 = Fin-tube Convector). Legend: Sensor 1 = Remote 541 tNt Universal Sensor 071 To isolate relay, cut jumper Factory installed jumper connects R to Rh (terminals 3 to 4) To isolate W relay, Other tN4 Thermostat External Class 2 cut jumper...

  • Page 6: Wiring The Thermostat

    Com and S1. 7 S1 Do not apply power to terminals 6 - 7, permanent Slab 6 Com damage to the sensors and / or thermostat will result! Sensor To various tekmar sensors © 2005 W 541 - 06/05 6 of 8...

  • Page 7: Troubleshooting The Wiring

    Troubleshooting the Wiring General The following tests are to be performed using standard 6 Com testing practices and procedures and should only be carried out by properly trained and experienced persons. A good quality electrical test meter, capable of reading from at least 0 - 300 V (ac), 0 - 2,000,000 Ohms, and testing for continuity is essential to properly test the wiring and sensors.

  • Page 8: Technical Data

    None – Optional tekmar type # 071, 070, 072, 073, 076, 077, 078, 079 The installer must ensure that this control and its wiring are isolated and / or shielded from strong sources of electromag- netic noise. Conversely, this Class B digital apparatus complies with Part 15 of the FCC Rules and meets all requirements of the Canadian Interference-Causing Equipment Regulations.

Table of Contents