Panasonic TH-65SQ1W Operating Instructions Manual page 80

■
[DIGITAL LINK(Ethernet control)]
Enables or disables the Ethernet connection via the
DIGITAL LINK terminal.
Note
●
When this setting is changed, the communication via
the LAN terminal is temporarily disconnected due to
setting switching. Do not change the setting during
LAN communication.
●
Video and audio from the DIGITAL LINK terminal are
not affected.
■
[DIGITAL LINK status]
Display the DIGITAL LINK connection environment.
Select [DIGITAL LINK status] with
<ENTER>.
DIGITAL LINK status
LINK status
HDMI status
Signal quality
Min
Max
[LINK status]:
1 of the followings will be displayed.
[No link]:
No LAN connection, etc.
[DIGITAL LINK]:
Connected to the DIGITAL LINK device by LAN.
[Long reach]:
Communication method is set to [Long reach] and
is connected to the DIGITAL LINK device by LAN.
[Ethernet]:
The PC is connected to the DIGITAL LINK / LAN
terminal of this product and is LAN connected.
[HDMI status]:
Displays the connection status of the HDMI format.
1 of the followings will be displayed.
[No HDMI]:
DIGITAL LINK not connected
[HDMI on]:
DIGITAL LINK connected
[HDCP on]:
HDCP supported on DIGITAL LINK
[Signal quality]:
It is the quantified minimum and maximum numbers
of errors that have occurred. The display colours are
red, yellow, or green, depending on the number.
Signal quality
-12dB or below
-11 to -8dB
-7dB or above
80
English
and press
No link
No HDMI
-XX dB
-YY dB
Display Reception
Colours Status
Green Good
Yellow Bad
Red Terrible
● The number is represented by yellow or red if
the LAN cable is disconnected or the cable is not
shielded.
●
This signal quality shows figures between the
twisted pair cable transmitter that is connected and
the display.
■
[DIGITAL LINK menu]
Displays the setting menu of Digital Interface Box.
Select [DIGITAL LINK menu] with
<ENTER>.
Note
● This function can only be selected when the
Panasonic device that supports DIGITAL LINK output
(ET-YFB100G, ET-YFB200G) is connected to a
DIGITAL LINK / LAN terminal and its power is on.
●
For details, refer to the manuals of the devices that
support DIGITAL LINK output.
■
[AMX D. D.]
Set whether to allow the Display to be detected by AMX
Device Discovery.
[Off]:
Disables detection by AMX Device Discovery.
[On]:
Enables detection by AMX Device Discovery.
●
For more details, visit the following web site.
http://www.amx.com/
■
[Crestron Connected]
When this function is set to [On], the Display can be
monitored or controlled via the network using equipment
and application software of Crestron Electronics, Inc.
This Display supports the following application software
from Crestron Electronics, Inc.
RoomView Express
•
Crestron Fusion
•
Crestron Connected is a function to connect to a system
developed by Crestron Electronics, Inc. which manages
and controls multiple system devices connected to the
network.
●
For details of Crestron Connected, refer to the
Crestron Electronics, Inc. web site (Provided only in
English).
http://www.crestron.com/
For the download of "RoomView Express", refer to
the Crestron Electronics, Inc. web site (Provided only
in English).
(https://www.crestron.com/en-US/resources/get-
roomview)
■
[Extron XTP]
Set to [On] when connecting XTP Transmitter made by
Extron to DIGITAL LINK terminal.
●
For more details on Extron, visit the following web
site.
http://www.extron.com
and press