Panasonic TH-65SQ1W Operating Instructions Manual page 64

Note
● The inputs set to [(Skip)] in [Input label] (see page 69)
are skipped when searching.
[Custom]: Repeatedly searches [Current input],
[1st search input] and [2nd search
input] in order, and switches to an input
with a signal.
[Input Monitors the inputs set to [On], detect
detection]: the status change from no signal to
signal present, and switches to the
input.
PC
Searching...
[Searching...] is displayed during the input search.
■
[Input search]: [Custom]
[1st search input], [2nd search input]
Set the input to search when [Custom] is selected.
[HDMI1] / [HDMI2] / [DisplayPort] / [DIGITAL LINK]
/ [DVI-D] / [SLOT] / [PC] / [USB] / [(None)]
■
[Input search]: [Input detection]
Input search
Input search
HDMI1
HDMI2
DisplayPort
DIGITAL LINK
DVI-D
PC
Changing delay
Sets the input to monitor during [Input detection].
[HDMI1] / [HDMI2] / [DisplayPort] / [DIGITAL LINK]
/ [DVI-D] / [PC]
[Off]: The input is not monitored.
[On]: The input is monitored.
■
[Changing delay]
Sets the delay time until the input is switched during
[Input detection].
[Off]: Switches the input if a signal is interrupted
even for a very short period.
1 ‒ 10: Sets the delay time (sec.).
Switches the input when the set time has
elapsed after detecting no signal is present.
However, if the detection period during
which no signal is present is shorter than the
set delay time, the input is not switched.
Note
●
[Input detection] is the function that automatically
switches the input as below by monitoring the
presence of signal for the set input.
If a video signal is input to the set input that is
•
not displayed (When the status has changed
from signal absent to signal present.), the input is
selected and switched.
64
English
Input detection
Off
Off
Off
Off
Off
Off
Off
If no signal is detected for the displayed input, the
•
setting switches to the set input to which a signal is
input. Also, if no signal is present for the displayed
input when the power is turned on or when the
input is switched, the setting switches to the set
input to which a signal is input. When signals are
input to multiple set inputs, the priority order as
default (immediately after power-on) is as follows:
HDMI1, HDMI2, DisplayPort, DIGITAL LINK,
DVI-D, PC.
In the other case (When the input is switched after
power-on), the input displayed last takes priority.
●
[Changing delay] is the function to prevent the
accidental input switch during a short period, such as
when the signal is interrupted due to the frequency
change for the input signal while [Input detection] is
operating.
If a signal is detected again within the set period
(sec.), the input is not switched.
●
[Input detection] may not operate correctly depending
on the image playback device.
Note
●
When set to the USB input, the unit determines no
signal is present if the USB memory is not connected
to the USB terminal.
In addition, even when a USB memory is connected,
if there is no playable file, the unit determines no
signal is present.
● This menu will be greyed out and cannot be set under
the following conditions.
[Failover/Failback] is set to the item other than
•
[Off]. (see page 65)
[Power management mode] is set to [Input
•
detection]. (see page 69)
[Input lock] is not set to [Off]. (see page 74)
•
When [Setup] - [Image settings] - [No signal image
•
settings] - [Display setting] is set to [On]. (see page
73)
● If the input is changed by this function, the last input
is selected when the power is turned on next time.
If you wish to retain the original input when the power
is turned on, set [Initial input] to the original input.
(see page 62)