Terex Genie GS-3232 Installation Instructions Manual
Smartlink software update
Hide thumbs
Also See for Genie GS-3232:
- Installation instructions manual (7 pages) ,
- Service and repair manual (341 pages) ,
- Operator's manual (107 pages)
Table of Contents
Advertisement
Quick Links
Dear valued customers, the firmware site has changed.
To complete this bulletin, install the most current version of the software.
Note: In 2014, Genie released "SmartLink Proportional Lift" control system upgrade kits for these machines.
Some of these machines may have been upgraded with the Proportional Lift control system.
1
Determine the "Application Firmware" installed in your machine.
Turn the key switch to the ground controls or platform controls position. Pull out the red Emergency Stop
button to the on position at both ground and platform controls.
Press the ground control scroll down button. The "Application Firmware" version will be displayed at the
LCD display.
2-Speed Lift = 137641
Proportional Lift = 1290381
2
Access the firmware website address below:
Link to Firmware site https://www.genielift.com/en/support/firmware
3
From the drop-down menu, select the model that is appropriate for your machine.
4
Locate and download the appropriate firmware/software file for your machine.
If you need assistance, contact your local Genie Product Support Team.
Mandatory Action Required
Advertisement
Table of Contents
Related Manuals for Terex Genie GS-3232
Summary of Contents for Terex Genie GS-3232
- Page 1 Dear valued customers, the firmware site has changed. To complete this bulletin, install the most current version of the software. Note: In 2014, Genie released "SmartLink Proportional Lift" control system upgrade kits for these machines. Some of these machines may have been upgraded with the Proportional Lift control system. Determine the "Application Firmware"...
-
Page 2: Safety Notice
This safety notice requires updating the control system software installed on your machine. Installation of the software must take place as soon as possible but no later than 15 days from receipt of the kit. Terex Aerial Work Platforms, 18340 NE 76th Street Redmond WA 98052, Ph: 800-536-1800, 425-881-1800 1 of 4... - Page 3 Note: If you cannot access the website, you may order thumb drive kit P/N 219268. One kit can be used on multiple machines. Terex Aerial Work Platforms, 18340 NE 76th Street Redmond WA 98052, Ph: 800-536-1800, 425-881-1800 2 of 4...
- Page 4 Important: Note the location on the computer where you downloaded the files. You will need it when performing the software update 6. Update the software installed on your machine by following instructions 219267. Terex Aerial Work Platforms, 18340 NE 76th Street Redmond WA 98052, Ph: 800-536-1800, 425-881-1800 3 of 4...
- Page 5 120013 SAFETY NOTICE To order parts: Machine owners with a valid Genie account can contact the Terex AWP parts department to place an order through one of the following: Genie Website: www.gogenielift.com Fax: 1-888-274-6192 Phone: 1-800-536-1800 Reimbursement: Only Genie Authorized Dealers will be reimbursed for labor or any other costs associated with this bulletin under the provisions of our standard warranty terms and conditions.
- Page 6 List any machines that could not be inspected or repaired because of the following: Model & Serial Number Scrapped Exported Stolen Others (explain) Fax to: United States 877-738-7530 Canada 425-498-7530 All other locations 001-425-498-7530 Terex Aerial Work Platforms, 18340 NE 76th Street Redmond WA 98052, Ph: 800-536-1800, 425-881-1800...
- Page 7 Installation Instructions SmartLink Software Update GS-3232 GS-3246 (PerSafety Notice 120013) Part No. 219267 Rev C...
-
Page 8: Observe And Obey
Instructions Rev C Introduction Introduction Introduction Tools Required: Laptop or desktop computer with an Ethernet Port and Internet Browser Torx T10 screw driver CAT5 Ethernet cable of suitable length Observe and Obey: Glossary of Terms This procedure shall be completed by a person trained and qualified on the repair of this ECM - Electronic Control Module machine. - Page 9 Rev C Instructions Procedure Procedure Locate the diagnostic port on the side of the Updating Machine Software GCON. Note: If the firmware 137641J was previously downloaded from the website or copied to your computer from a thumb drive it must be deleted from your computer before continuing.
- Page 10 Instructions Rev C Procedure 10 Launch a web browser such as Internet 13 Select the Reprogram Device (s) button to ® ® Explorer or Firefox on your PC or laptop. start the ECM software update. Type in the IP address from steps 8 and 9 into Result: The following screen will be displayed the web browser address bar and press Enter.
- Page 11 Rev C Instructions Procedure Pull out the red Emergency Stop button to the Platform Overload Option on position at the ground controls. (GS-3232 and GS-3246 models) Result: The ground controls LCD display will show the following: The previous Rev J software update may have enabled the Platform Overload Option.
- Page 12 Result: The ground controls LCD display shows the following. Continue with step 10. 14 Fill out and sign the attached completion form and fax or email to Terex AWP Warranty Department. This will serve as verification that you have completed Safety Notice 120013.120013.
-
Page 13: Test Procedure
Rev C Instructions Procedure If you have any further questions regarding these Test Procedure instructions or need assistance, please contact Genie Product Support at one of the following (GS-3232 models) telephone numbers: Turn the key switch to the PCON position. Pull United States: 800-536-1800 out the red Emergency Stop buttons to the on... - Page 14 All other locations 001-425-881-1800 10 Return the machine to service. 11 Fill out and sign the attached completion form and fax or email to Terex AWP Warranty Department. This will serve as verification that you have completed Safety Notice 120013.120013.
- Page 15 Your signature on this form will verify that you have completed Safety Notice 120013 on the machines listed below. Please note that this is not a Warranty Claim Form. A Warranty Claim Form must be submitted to the Terex AWP Warranty Department for reimbursement under the provisions of our standard warranty terms and conditions.