Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Game Winner Climber 2.0
Summary of Contents for Game Winner Climber 2.0
-
Page 2: Table Of Contents
Table of Contents Page Warnings ……………………………………………………………………. 3-8 Tools Required .......…………………………………………… 8 Parts List …………………………………………………………………….. 9 Hardware …………………………………………………………………….. 10 Product Diagram …………………………………………………………… 11 Assembly Instructions …………………………………………………….11-14 Installation Instructions …………………………………………………… 15-23 Removal Instructions ………………………………………………………. 24 Care and Maintenance …………………………………………………….. 24 Warranty Information ………………………………………………………. 25 Note: Before beginning assembly of product, make sure all parts are present. -
Page 3: Warnings
WARNING! Thoroughly inspect this or any other Game Winner product(s) prior to use for signs of wear, rot, corrosion, cracks, fraying, deterioration, and/ or any other type of damage. DO NOT use this or any other Game Winner product(s) if they show evidence of wear, rot, corrosion, cracks, fraying, deterioration, and/ or any other type of damage. - Page 4 RELIEVES INNOPOWER INC. OF ANY RESULTANT LIABILITIES AND MAY RESULT IN SERIOUS INJURY OR DEATH! WARNING! Prior to attempting to use this or any Game Winner product(s), you must take a moment and become familiar with its assembly, setup, installation, and removal. You must practice setting-up, using, and removing the product(s) at ground level prior to attempting to use it at heights above ground-level.
- Page 5 Warnings WARNING! The length of the full-body fall arrest tether must be minimized at all times. It should be adjusted so that it is above the head with no slack (snug) in the sitting position and you should have the minimum amount of slack possible when climbing. Failure to follow these instructions may result in serious injury or death! WARNING! Failure to follow harness instructions could result in not being able to return to the stand and being suspended in a harness after a fall.
- Page 6 Failure to follow these instructions may result in serious injury or death! WARNING! DO NOT use this or any other Game Winner product(s) if you have a history of heart problems, back problems, impaired vision, joints that lock-up, spinal fusions, equilibrium...
- Page 7 Failure to follow these instructions may result in serious injury or death! WARNING! A connector strap has been included with your Game Winner climber. It is designed to connect the standing platform to the seating platform. In the unlikely event you lose contact with either while climbing, this connector strap allows you to regain control.
-
Page 8: Tools Required
Warnings FULL-BODY FALL ARREST HARNESS SYSTEM (FAS) A full-body fall arrest harness has been included with this product for your use. The full-body fall arrest harness has been designed to keep you from experiencing a fall. Remember, the most important part of your hunt is returning home to your family safe and sound. READ THE FULL-BODY FALL ARREST HARNESS MANUAL CAREFULLY AND FOLLOW ALL THE INSTRUCTIONS! YOUR NEW FULL-BODY FALL ARREST HARNESS IS DESIGNED FOR A MAXIMUM CAPACITY OF 300 POUNDS (136kg). -
Page 9: Parts List
Parts List Assembled Seating Platform (includes Platform, Cable, Shoulder Straps, Cable Support Arms， Cable Locking Pins and M8x60 Bolts) Assembled Standing Platform (includes Platform, Cable, Foot Straps, Cable Support Arms, Cable Locking Pins and M8x60 Bolts) Seat Cushion Ratchet Tree Strap with 2 Hooks Cable Cinch Strap... -
Page 10: Hardware
Hardware Step M8X60 (with 2 steel washers, and 1 locknut) (preassembled on standing platform) Step M8X60 (with 2 steel washers and 1 locknut) (preassembled on seating platform) -
Page 11: Product Diagram
Product Diagram Product Identification Mark for Customer Service Assembly Instructions Step 1: Locate the Cable Support Arms of Standing Platform. Rotate the Cable Support Arms up into an erect position and secure using two (2) M8x60 Bolts, four (4) Steel Washers and two (2) Locknuts (preassembled on support bar) as shown in Figure 1. - Page 12 Assembly Instructions Step 2: Locate the Cable Support Arms of Seating Platform. Rotate the Cable Support Arms up into an erect position and secure using two (2) M8x60 Bolts, four (4) Nylon Washers and two (2) Locknuts (preassembled on support bar) as shown in Figure 2. WARNING! DO NOT overtighten the hardware.
- Page 13 Assembly Instructions Step 4: Locate the two Cable Assemblies. You will notice that there are two molded ends on the cables. Insert one of these molded ends into the receiver on the Cable Support Arms as shown in Figure 4. One end of cable must be secured onto the cable support arm (Step 5) before...
- Page 14 Assembly Instructions Step 6: Locate the Seat Cushion. Unfasten the buckles that are attached on seat. Slip the Seat Cushion into the Seating Platform. Lay the seat straps over the Seating Platform frame and thread buckles as shown in Figure 6. NOTE: Lengthen or shorten the seat straps to a comfortable seating height.
-
Page 15: Installation Instructions
Installation Instructions SELECTING A SAFE TREE: TREESTAND MINIMUM AND MAXIMUM TREE SIZE: 9 – 22” DIAMETER! Never use treestand on a dead, leaning, diseased, loose barked tree, tree with excessive vines, or on a utility pole, or any other man made structure. Never use on trees that contain nails, screws, or other sharp objects that may cut, sever, or puncture strap webbing or cables! WARNING! - Page 16 If such damage is visible or suspected, DO NOT USE THE PRODUCT. Failure to follow these instructions can result in serious injury or death. SETTING UP THE GAME WINNER CLIMBER ONTO THE TREE Step 1: Place the Standing Platform approximately 12 inches off the ground on the base of tree.
- Page 17 For Cable Cinch Strap threading instructions refer to Figure 10. WARNING! The Cable Cinch Straps have been included to help stabilize this Game Winner climber treestand. They must be engaged after reaching Figure 9 Install Cable Cinch Straps climbing height. You must disengage the Cable Cinch Straps prior to attempting to climb down.
- Page 18 Installation Instructions ADJUSTING CLIMBER ANGLE FOR GRADUAL TREE NARROWING To properly set up your Game Winner climber treestand, you must take into consideration the gradual narrowing of the tree. To compensate for this gradual narrowing, you must tilt both of...
- Page 19 Installation Instructions Prior to every use, inspect cables, seat, and all hardware for damage, including corrosion. DO NOT USE THIS PRODUCT IF ANY DAMAGE IS SUSPECTED, including but not limited to cuts, frayed portions, corrosion, bends, or other damage to treestand, straps, or cables. If such damage is visible or suspected, DO NOT USE THE PRODUCT.
- Page 20 Installation Instructions ASCENDING (CLIMBING UP) THE TREE Step 1: Read and understand included Full Body Double check to assure you are Harness instructions, warnings, and watch wearing and properly attached to tree safety video for instructions on using your with full body harness. If you are not, Full Body Harness with tree strap.
- Page 21 Installation Instructions Step 5: Raise harness tree strap higher up tree according to harness manufacturers instructions as shown in Figure 17. Lift up seating platform as shown in Figure 18 so it is at waist high. WARNING! ALWAYS KEEP HARNESS TETHER SLACK AT MINIMUM.
- Page 22 Installation Instructions Step 7: Sit on climbing bar so teeth bite into tree. Once you reach your desired hunting Never jump or bounce on climbing bar to height position, adjust the seating platform seat/dig teeth into tree. so it is at comfortable sitting height. Always attach security straps to top and bottom Sit on climbing bar so teeth bite into tree.
- Page 23 Installation Instructions Step 7: Sit on climbing bar so teeth bite into tree. Once you reach your desired hunting Never jump or bounce on climbing bar to height position, adjust the seating seat/dig teeth into tree. platform so it is at comfortable sitting Always attach security straps to top and bottom height.
-
Page 24: Removal Instructions
Replace tree strap and cables every two years or sooner if wear, damage, deterioration, rust, cuts, tears, rot, etc. or vandalism is detected or suspected. Only replace with official Game Winner replacement parts. Replace full body harness every three years or sooner if wear, damage, deterioration, cuts, tears, rot, etc. -
Page 25: Warranty Information
I have read and understand the safety, assembly and operating instructions provided with my Game Winner product. I have read the warranty information and know that I can call Innopower Inc. at (949) 262-3416 with any questions or concerns that I may have about this or any other Game Winner product.