Advertisement
Quick Links
HD-AVS Dome
Cameras
Quick Start Guide
Table Of Contents
Features and Specifications
A.
Overview
B.
Cable Interface
Camera Installation
A.
Installation Steps
B.
Lens Adjustment
C.
Waterproofing Connectors
FAQ and Lightning Protection
A.
FAQ
www.icrealtime.com
IMPORTANT SAFEGUARDS AND WARNINGS
Electrical Safety
All installation and operation here should conform to your local electrical safety codes. The
power shall conform to the requirement in the SELV (Safety Extra Low Voltage). Please check
product specifications for power requirements. We assume no liability or responsibility for all
the fires or electrical shock caused by improper handling or installation. We are not liable for
any problems caused by unauthorized modification or attempted repair.
Transportation Security
Care must be given to avoid heavy stress, violent vibration or water damage during
transportation, storage and installation.
Installation
Do not apply power to the camera before completing installation. Please install the proper
power cut-off device during the installation connection. Always follow the instruction guide the
manufacturer recommended.
Qualified engineers needed
All the examination and repair work should be done by the qualified service engineers. We are
not liable for any problems caused by unauthorized modifications or attempted repair.
Environment
This series network camera should be installed in a cool, dry place away from direct sunlight,
2
inflammable, explosive substances and etc. Please keep it away from the electromagnetic
2
radiation object and environment. Please make sure the CCD (CMOS) component is out of the
radiation of the laser beam device. Otherwise it may result in CCD (CMOS) optical component
damage. Please keep the sound ventilation. Do not allow the water and other liquid falling into
3-4
the camera. Lightning-proof device is recommended to be adopted to better prevent lightning
4
damage. The grounding studs of the product are recommended to be grounded to further
enhance the reliability of the camera.
4
Daily Maintenance
Please shut down the device and then unplug the power cable before you begin daily
5
maintenance work. Do not touch the CCD (CMOS) optic component. You can use the blower to
clean the dust on the lens surface. Always use the dry soft cloth to clean the device. If there is
too much dust, please use the water to dilute the mild detergent first and then use it to clean
the device. Finally use the dry cloth to clean the device. Please put the dustproof cap to protect
the CCD (CMOS) component when you do not use the camera.
Accessories
Be sure to use all the accessories recommended by manufacturer. Before installation, please
open the package and check all the components are included. Contact your local retailer ASAP
if something is broken in your package.
Advertisement
Related Manuals for IC Realtime HD-AVS
Summary of Contents for IC Realtime HD-AVS
- Page 1 fires or electrical shock caused by improper handling or installation. We are not liable for any problems caused by unauthorized modification or attempted repair. Transportation Security HD-AVS Dome Care must be given to avoid heavy stress, violent vibration or water damage during transportation, storage and installation.
- Page 2 1A. OVERVIEW This series Dome style camera utilizes High Definition Advanced 1B. Cable Interface Video System (HD-AVS) technology, an HD-over-coaxial cable See Figure 1-1 for cable interface identification. Outputs may vary video standard that allows long-distance, HD transmission of depending on model.
- Page 3 2A. INSTALLATION STEPS Step 1 Use the included position map and drill the appropriate Step 3 Use the wrench included with the camera to remove the Dome mounting holes and cable exit, if necessary. See Figure 2-1. cover screws on the camera base. Thread the cabling through cable exit if necessary.
- Page 4 Step 5 You can also adjust the camera rotation from the base as well as 2B. Lens Adjustment (available in some models) Some models feature a zoom and focus adjustment. Remove the the lens as necessary. See Figure 2-5. Dome cover and locate the adjustment knobs as shown in Figure 2-7.
- Page 5 3A. FAQ Check whether the power supply is ● properly connected. No image after the Check recorder video format and ● resolution compatibility with Camera Device is powered on Check whether the main power and ● transformer are working normally. Use the required power supply.
Need help?
Do you have a question about the HD-AVS and is the answer not in the manual?
Questions and answers