Isec-Wl-Touch "System Diagnostics" And "Autoenroll; Isec-Wl-Touch2 - NAPCO iSecure Installation & Programming Instructions

ISEC-WL-TOUCH "System Diagnostics" and "AutoEnroll"

System Diagnostics
The ISEC-WL-TOUCH "System Diagnostics" screen shown
below is exclusive to the ISEC-WL-TOUCH 4.3-inch 900MHz
Color Touchscreen Wireless Keypad. It is designed to help
you find the optimum mounting location for your ISEC-WL-
TOUCH keypad by displaying the signal strength of the
900MHz radio signal link between the Go-Anywhere Hub and
the ISEC-WL-TOUCH keypad within the installation environ-
ment. This screen is accessed by tapping the Settings
("gears") icon, then tapping the DIAG button.
Each button and field in this screen is described below:
Learned
Checked when the status of the ISEC-WL-TOUCH key-
pad is paired into the iSecure system; otherwise un-
checked.
RF Channel #
Displays the frequency of the channel used for communi-
cations between the Go-Anywhere Hub and the ISEC-WL
-TOUCH keypad.
RSSI_kp (dBm)
RSSI (Received Signal Strength Indicator) is a measure-
ment of the power present in a received radio signal.
This field displays the 900MHz radio signal that the ISEC-
WL-TOUCH keypad received from the Go-Anywhere
Hub.
RSSI_xcvr (dBm)
The RSSI value that the Go-Anywhere Hub received from
this ISEC-WL-TOUCH Keypad.
Operating Freq (MHz)
Displays the wavelength, in megahertz, of the radio fre-
quency used in communications between the Go-
Anywhere Hub and the ISEC-WL-TOUCH keypad.
Out of System in (sec)
Displays the number of seconds the communication link
between the Hub and the ISEC-WL-TOUCH keypad was
interrupted. If Out of System, this field will count down.
AutoEnroll
This feature is a quick and easy way to enroll wireless devices
into your iSecure system. Before you begin, remove the bat-
tery from the wireless device. With the unpowered wireless
device physically "in hand", and with its battery within reach
(always use fresh batteries), perform the following steps using
the ISEC-WL-TOUCH keypad:
1. Press and hold the System Settings ("gear") icon, enter
your Dealer password, then tap ENTER.
The keypad red and green LEDs will flash simultaneous-
ly, while a "please wait" message appears.
Napco iSecure Security System
2. In the System Settings
3. Tap the Zone # button
4. Tap the AutoEnroll but-
5. Install the battery into the
6. Ensure the Wireless ID
7. Ensure the Area selections are correct for the specific

ISEC-WL-TOUCH2

The enhanced model ISEC-WL-TOUCH2 includes
an internal USB connector in the event a graphics
update and/or restore is required. This USB is not
for general use and is to be used ONLY with in-
structions and files from NAPCO Technical Support.
All technical manuals are available in PDF format at
screen, tap Sensor Con-
figuration.
and enter the zone num-
ber into which you wish
to add the device (for
example tap 0 2 for zone
2).
ton.
wireless device.
# field is populated with the same transmitter ID number
printed on a sticker affixed to the device (location of the
sticker varies with each device; check the transmitter rear
housing or PC board).
transmitter to be enrolled, then tap Save.
Note: After AutoEnrolling transmitters, be sure to upload
the new data to the iSecure Cloud Web Portal
(www.iSecureByNapco.com) and test the device. See
page 6, Dealer Programming for more information.
tech.napcosecurity.com
ISEC-WL-TOUCH
Wireless 900MHz
Touchscreen
65