1. Manuals
  2. Brands
  3. Shuttle Manuals
  4. Motherboard
  5. AV14
  6. User manual

Shuttle AV14 User Manual

Ppga celeron processor based agp main board
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
AV14
PPGA Celeron processor
Based AGP
MAIN BOARD
User's Manual

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the AV14 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Shuttle AV14

Summary of Contents for Shuttle AV14

  • Page 1 AV14 PPGA Celeron processor Based AGP MAIN BOARD User's Manual...
  • Page 2 Shuttle Inc. Disclaimer Shuttle Inc. shall not be liable for any incidental or consequential damages resulting from the performance or use of this product. This company makes no representations or warranties regarding the contents of this manual.

  • Page 3: Table Of Contents

    2.1 SPECIFICATIONS ....................7 3 HARDWARE INSTALLATION ............. 10 3.1 STEP BY STEP INSTALLATION ..............10 Accessories Of AV14 ..................10 STEP 1 Install the CPU................... 11 STEP 2 Set Jumpers ..................12 STEP 3 Install SDRAM System Memory ............. 12 STEP 4 Install Internal Peripherals in System Case ........
  • Page 4 STEP 11 Connect External Peripherals to Back Panel ......19 STEP 12 First Time System Boot Up ............20 STEP 13 Install Drivers & Software Components ........21 3.2 JUMPER SETTINGS .................... 22 Jumpers & Connectors Guide ................ 23 Set Keyboard & PS/2 Mouse Power-On (JP3) ........... 25 Clear CMOS (JP12) ..................
  • Page 5 3.3 SYSTEM MEMORY CONFIGURATION ............36 Install Memory ....................36 Upgrade Memory ..................... 36 4 SOFTWARE UTILITY ................36 4.1 AV14 MAINBOARD CD OVERVIEW............... 37 4.2 INSTALL MAINBOARD DRIVER ..............38 4.3 TO VIEW THE USER'S MANUAL ..............39 5 BIOS SETUP ..................40 5.1 ENTERING BIOS ....................

  • Page 6: What's In The Manual

    WHAT’S IN THE MANUAL Quick Reference Hardware Installation >> Step-by-Step ............Page 10 Jumper Settings >> A Closer Look ............Page 22 Software Utility >> How to Install ..............Page 37 BIOS Setup >> How to Configure ............... Page 40 About This Manual For First-Time DIY System Builder ..............Page 5 For Experienced DIY User ................Page 5...

  • Page 7: Introduction

    Experienced DIY User Congratulations on your purchase of the Shuttle AV14 mainboard. You will find that installing your new Shuttle AV14 mainboard is just that easy. Bundled with an array of onboard functions, the highly-integrated AV14 mainboard pro- vides you with a total solution to build the most stable and reliable system.

  • Page 8: Item Checklist

    1.2 Item Checklist Check all items you received with your AV14 mainboard to make sure nothing is missing. The complete package should include: - One Shuttle AV14 Mainboard A W A R D A l l r i g h t s r e s e r v e d...

  • Page 9: Features

    2 FEATURES The AV14 mainboard is carefully designed for the demanding PC user who wants high performance and maximum intelligent features in a compact package. 2.1 Specifications - - CPU Support Support Intel PPGA Celeron Processor 300 ~ 500+ MHz...
  • Page 10 format or for 5.25-inch FDD with 360KB or 1.2MB format. Ø 1 × PS/2 mouse connector Ø 1 × PS/2 Keyboard connector Ø 2 × USB connectors Ø 2 × DB9 Serial connectors 16550 UART compatible Ø 1 × Infrared communications port ASKIR and HPSIR compatible. (Serial port COM2 can also be redirected to an external IrDA Adapter for wireless connection.) Ø...
  • Page 11 System board conforms to the ATX specification. Board dimensions: 304mm × 190mm - - Advanced Features Ø Dual Function Power Button - The system can be in one of two states, one is Suspend mode and the other is Soft-Off mode. Pushing the power button for less than 4 seconds places the system into Suspend mode.

  • Page 12: Hardware Installation

    3 HARDWARE INSTALLATION This section outlines how to install and configure your AV14 mainboard. Refer to the following mainboard layout to help you identify various jumpers, connectors, slots, and ports. Then follow these steps designed to guide you through a quick and correct installa- tion of your system.

  • Page 13: Step 1 Install The Cpu

    Step 1 Install the CPU: 1. Locate the CPU ZIF (Zero Insertion Force) socket on the upper-right sector of your mainboard (between the back-panel connectors and the DIMM memory banks). 2. Pull the CPU ZIF socket lever slightly sideways away from the socket to unlock the lever, then bring it to an upward vertical position.

  • Page 14: Step 2 Set Jumpers

    Step 2. Set Jumpers This mainboard is jumperless! The default jumper settings have been set for the common usage standard of this mainboard. Therefore, you do not need to reset the jumpers unless you require special adjustments as in any cases below : 1.

  • Page 15: Step 4 Install Internal Peripherals In System Case

    Step 4 Install Internal Peripherals in System Case Before you install and connect the mainboard into your system case, we recommend that you first assemble all the internal peripheral devices into the computer housing, including but not limited to the hard disk drive (IDE/ HDD), floppy disk drive (FDD), CD-ROM drive, and ATX power supply unit.

  • Page 16: Step 5 Mount The Mainboard On The Computer Chassis

    Step 5 Mount the Mainboard on the Computer Chassis 1. You may find that there are a lot of different mounting hole positions both on your computer chassis and on the mainboard. To choose a correct mounting hole, the key point is to keep the back-panel of the mainboard in a close fit with your system case, as shown below.

  • Page 17: Step 6 Connect Front Panel Switches/Leds/Speaker

    Step 6 Connect Front Panel Switches/LEDs/Speaker You can find there are several different cables already existing in the system case and originating from the computer’s front-panel devices (HDD LED, Power LED, Reset Switch, PC Speaker, etc.) These cables serve to connect the front-panel switches and LEDs to the mainboard’s front-panel connectors group, as shown below.
  • Page 18 4. HDD-LED (HDLED) PW LED JP 13 RST HD LED GLED EPMI PON 5. Power-LED (PW LED) PW LED JP 13 RST HD LED GLED EPMI PON 6. Hardware Reset Switch (RST) PW LED JP 13 RST HD LED GLED EPMI PON 7.

  • Page 19: Step 7 Connect Ide & Floppy Disk Drives

    Step 7 Connect IDE & Floppy Disk Drives 1. IDE cable connector 2. FDD cable connector Step 8 Connect Other Internal Peripherals 1. IR connector - 17 -...

  • Page 20: Step 9 Connect The Power Supply

    Step 9 Connect the Power Supply 1. System power connector Step 10 Install Add-on Cards in Expansion Slots 1. Accelerated Graphics Port (AGP) Card 2. PCI Card 3. ISA Card - 18 -...

  • Page 21: Step 11 Connect External Peripherals To Back Panel

    Step 11 Connect External Peripherals to Back Panel You are now ready to put the computer case back together and get on to the external peripherals connections to your system’s back-panel. 1. PS/2 Mouse and PS/2 Keyboard PS/2 Mouse PS/2 keyboard 2.

  • Page 22: Step 12 First Time System Boot Up

    Step 12 First Time System Boot Up To assure the completeness and correctness of your system installation, you may check the above installation steps once again before you boot up your system for the first time. 1. Insert a bootable system floppy disk (DOS 6.2x, Windows 95/98/NT, or others) which contains FDISK and FORMAT utilities into the FDD.

  • Page 23: Step 13 Install Drivers & Software Components

    Make sure your Windows 9x operating system is already installed before running the drivers installation CD-ROM programs. 1. Insert the AV14 bundled CD-ROM into your CD-ROM drive. The auto-run program will display the drivers main installation window on screen.

  • Page 24: Jumper Settings

    3.2 Jumper Settings Several hardware settings are made through the use of jumper caps to con- nect jumper pins on the mainboard. Pin #1 could be located at any corner of each jumper, you just find a white right angle on the mainboard, that's pin 1#.

  • Page 25: Jumpers & Connectors Guide

    Jumpers & Connectors Guide Use the mainboard layout on page 10 to locate CPU socket, memory banks, expansion slots, jumpers and connectors on the mainboard during the instal- lation. The following list will help you to identify jumpers, slots, and connec- tors along with their assigned functions: CPU/Memory/Expansion Slots Socket370 : CPU Socket for FC-PGA/PPGA 370 processors...
  • Page 26 JP12 : Clear CMOS JP16 : CPU Multiplier JP14 : System clock setting : CPU clock ratio setting Back Panel Connectors : PS/2 Keyboard : PS/2 Mouse : 2 × USB (Universal Serial Bus) COM1 : Serial Port 1 (DB9 male) COM2 : Serial Port 2 (DB9 male) PRINTER : Parallel Port (DB25 female)

  • Page 27: Set Keyboard & Ps/2 Mouse Power-On (Jp3)

    Set PS/2 Keyboard & PS/2 Mouse Power-On (JP3) AV14 mainboard provides an easy power-on by PS/2 keyboard and PS/2 mouse. Note: When you enable Keyboard Power-On, you also need to configure the proper hot-key combination <Ctrl> + < function key F1 ~ F12 >...

  • Page 28: Clear Cmos (Jp12)

    Clear CMOS (JP12) JP12 is used to clear CMOS data. Clearing CMOS will result in perma- nently erasing the previous system configuration settings and restoring the original (factory-set) system settings. Pin 1-2 (Default) Pin 2-3 (Clear CMOS) Step 1. Turn off the system power (PC-> Off) Step 2.

  • Page 29: Cpu Clock Ratio Setting (Jp9)

    Front Side Bus (FSB) Speed Auto Config. Setting (JP16 and JP14) AV14 provides jumper JP14 and JP16 to set auto configure front side bus at 66MHz, 100MHz and 133MHz. Inserting mini-jumper caps on JP16 and leave JP14 all open as below to identify automatically the FSB speed.

  • Page 30: Front Side Bus(Fsb) Speed Auto Config. Setting (Jp15 And Jp14)

    CPU Clock Ratio Setting (JP9) AV14 mainboard provides a jumper group JP9 to set CPU speed configure by BIOS or by hardware jumper. By inserting jumper pack on Manual group properly, the user can configure the CPU Clock Ratio manually.

  • Page 31: Ps/2 Keyboard & Ps/2 Mouse Connectors

    PS/2 Keyboard & PS/2 Mouse Connectors Two 6-pin female PS/2 keyboard & Mouse connectors are located at the rear panel of the mainboard. Depending on the com- PS/2 Mouse puter housing you use (desktop or minitower), the PS/2 Mouse connector is situated at the top of the PS/2 Keyboard connector when the mainboard is laid into a desktop, as opposed to a minitower...

  • Page 32: Hardware Reset Connector (Rst)

    Hardware Reset Connector (RST) Attach the 2-pin hardware reset switch cable to the RST header. Pressing the reset switch causes the system to restart. HDD LED Connector (HDLED) Attach the connector cable from the IDE device LED to the 2-pin HDD LED header. The HDD LED lights up whenever an IDE device is active.

  • Page 33: Atx Power On/Off Switch Connector (Pon)

    ATX Power On/Off Switch Connector (PON) The Power On/Off Switch is a momen- tary type switch used for turning on or off the system’s ATX power supply. Attach the connector cable from the Power Switch to the 2-pin PWON header on the mainboard.

  • Page 34: Enhanced Ide Ports And Floppy Connectors

    Enhanced IDE Ports and Floppy Connectors The AV11 mainboard features two 40-pin dual-channel IDE device connec- tors (IDE1/IDE2) providing support for up to four IDE devices, such as CD- ROM and Hard Disk Drives (H.D.D.). This mainboard also includes one 34-pin floppy disk controller (FDC) to accommodate the Floppy Disk Drive (F.D.D.).

  • Page 35: Ir Connector (J4)

    IR Connector (J4) If you have an Infrared device, this mainboard can implement IR transfer function. To enable the IR transfer function, follow these steps: IR Pin Assignments: 1=VCC 2=NC 3=IRRX 4=GND 5=IRTX Note: Please make sure to refer on board IR Pin Assignments to match your IR devices cable.

  • Page 36: Sb-Link Connector (Jp10)

    SB-Link Connector (JP10) The mainboard provides a 2x3 pin SB-Link header accepts the Creative CT4600 se- ries PCI sound cards with PCI solution to connect the legacy Sound Blaster compat- ible audio to the PCI bus. SB-Link Pin Assignments: 1=GNT#A 2=GND 3=Empty 4=REQ#A...

  • Page 37: Atx Power Supply Connector (J5)

    ATX Power Supply Connector (J5) Locate the 20-pin male header ATX power connector (J5) on your mainboard. Plug the power cable from the ATX power supply unit directly into J5 ATX power supply connector. Note 1: The ATX power connector is directional and will not go in unless the guides match perfectly.

  • Page 38: System Memory Configuration

    Checking) and ECC (Error Checking and Correction) in the memory array. In EC mode, single and multiple bit error detection is provided. In ECC mode, when the memory is being read from DRAM, the AV14 provides both error checking and correction of the data.

  • Page 39: Software Utility

    Install Mainboard Software - Installing Mainboard Drivers for Windows Manual - AV14 series mainboard user's manual in PDF format. Link to Shuttle Homepage - Link to shuttle website homepage. Browse this CD - Allows you to see the contents of this CD.

  • Page 40: Install Mainboard Driver

    Insert the attachment CD into your CD-ROM drive and the CD AutoRun screen should appear. If the AutoRun screen does not appear, double click on Autorun icon in My Computer to bring up Shuttle Mainboard Software Setup screen. Select using your pointing device (e.g. mouse) on the “Install Mainboard Software”...

  • Page 41: To View The User's Manual

    Insert the attachment CD into your CD-ROM drive and the CD AutoRun screen should appear. If the AutoRun screen does not appear, double click on Autorun icon in My Computer to bring up Shuttle Mainboard Software Setup screen. Select using your pointing device (e.g. mouse) on the “Manual” bar.

  • Page 42: Bios Setup

    5 BIOS SETUP AV14 BIOS ROM has a built-in Setup program that allows users to modify the basic system configuration. This information is stored in battery-backed RAM so that it retains the Setup information even if the system power is turned off.

  • Page 43: The Main Menu

    5.2 The Main Menu Once you enter the AwardBIOS(tm) CMOS Setup Utility, the Main Menu will appear on the screen. The Main Menu allows you to select from several setup functions and two exit choices. Use the arrow keys to select among the items and press <Enter>...
  • Page 44 PC Health Status This entry shows the current system temperature, voltage and Fan speed. Frequency/Voltage Control Use this menu to specify your settings for frequency/voltage control. Load Fail-Safe Defaults Setup defaults loads the values required by the system for the O.K. performance.

  • Page 45: Standard Cmos Setup

    Standard CMOS Setup The items in Standard CMOS Setup Menu are divided into 10 catego- ries. Each category includes no, one or more than one setup items. Use the arrow keys to highlight the item and then use the <PgUp> or <PgDn>...
  • Page 46 If you select Type User, related information is asked to be entered to the following items. Enter the information directly from the keyboard and press <Enter>. Those information should be provided in the docu- mentation from your hard disk vendor or the system manufacturer. The user may also set those items to AUTO to auto configure hard disk drives parameter when system power-on.

  • Page 47: Bios Features Setup

    BIOS Features Setup Virus Warning When this item is enabled, the Award BIOS will monitor the boot sector and partition table of the hard disk drive for any attempt at modification. If an attempt it made, the BIOS will halt the system and the following error message will appear.
  • Page 48 External Cache This item enables CPU secondary cache to speed up memory access. Ø The choice: Enabled, Disabled. CPU L2 Cache ECC Checking When you select Enabled, memory checking is enable when the exter- nal cache contains ECC SRAMs. Ø The choice: Enabled, Disabled. Processor Number Feature Allows you to Enabled/Disabled, the processor serial number.
  • Page 49 Gate A20 Option This entry allows you to select how the gate A20 is handled. The gate A20 is a device used to address memory above 1 MByte. Initially, the gate A20 was handled via a pin on the keyboard. Today, while key- boards still provide this support, it is more common, and much faster, set to Fast for the system chipset to provide support for gate A20.
  • Page 50 Video BIOS Shadow Determines whether video BIOS will be copied to RAM. However, it is optional depending on chipset design. Video Shadow will increase the video speed. Ø The choice: Enabled, Disabled. C8000-CBFFF Shadow/DC000-DFFFF Shadow These categories determine whether option ROMs will be Chipset Features Setup Auto Configuration copied to RAM.

  • Page 51: Chipset Features Setup

    Chipset Features Setup Bank x/x DRAM Timing This value in this field is set by the system board manufacturer, depend- ing on whether the board has paged DRAMS or EDO DRAMS. Ø The choice: SDRAM 10ns, SDRAM 8ns, Normal, Medium, Fast, Turbo.
  • Page 52 P2C/C2P Concurrency This item allows you to enabled/disabled the PCI to CPU, CPU to PCI concurrency. Fast R-W Turn Around This item controls the DRAM Timing. It allows you to enabled/Disabled the fast read/write turn around. Ø The choice: Enabled, Disabled. System BIOS Cacheable This item allows the user to set whether the system BIOS F000~FFFF areas are cacheable or non-cacheable.
  • Page 53 AGP Fast Write This item allows user to enable/disable AGP Fast Write function. Ø The choice: Enabled, Disabled. On Chip USB Select Enabled if your system contains a Universal Serial Bus (USB) controller and you have a USB peripheral. Ø The choice: Enabled, Disabled. USB Keyboard Support Select Enabled if your system contains a Universal Serial Bus (USB) controller and you have a USB keyboard.
  • Page 54 AGP Master 1 WS Write This implements a single delay when writing to the AGP Bus. By de- fault, two-wait states are used by the system, allowing for greater stabil- ity. Ø The choice: Enabled, Disabled. AGP Master 1 WS Read This implements a single delay when reading to the AGP Bus.

  • Page 55: Integrated Peripherals

    Integrated Peripherals OnChip IDE Channel0 This item is used to defined on chip Primary PCI IDE controller is Enable or Disable setting. Ø The choice: Enabled, Disabled. OnChip IDE Channel1 This item is used to defined on chip Secondary PCI IDE controller is Enable or Disable setting.
  • Page 56 Primary Master / Slave PIO In this items, there are five modes defined in manual mode and one automatic mode. There are 0, 1, 2, 3, 4, and AUTO is the default settings for on board Primary Master / Slave PIO timing. Ø...
  • Page 57 POWER ON Function This item is used to defined Keyboard & PS/2 mouse power-on func- tion enabled or disabled. Ø The choice: Password, Hot KEY, Mouse Left, Mouse Right, Button Only, keyboard 98. Note:1. When item of PS/2 Mouse or HOT-Key is selected, please also adjust jumper JP3 to the proper position.
  • Page 58 UART Mode Select The main board support IrDA(HPSIR) and Amplitudes Shift Keyed IR(ASKIR) infrared through COM 2 port. Note : FIR is not available currently. Ø The choice: IrDA, ASKIR, Normal. UART2 Duplex Mode This item specifies onboard infrared transfer mode to full-duplex. This item will not show up when IrDA, ASKIR modes are selected.

  • Page 59: Power Management Setup

    Power Management Setup The Power Management Setup allows you to configure you system to most effectively save energy while operating in a manner consistent with your own style of computer use. ACPI Function This item allows you to Enabled/Disabled the Advanced Configuration and Power Management (ACPI) Ø...
  • Page 60 PM Control by APM If this item set to No, system BIOS will be ignored and APM calls the power to manage the system. If this item setup to Yes, system BIOS will wait for APM's prompt before it enter any PM mode e.g. DOZE, STANDBY or SUSPEND. Ø...

  • Page 61: Pnp/Pci Configuration

    PnP/PCI Configuration This section describes configuring the PCI bus system. PCI, or Per- sonal Computer Interconnect, is a system which allows I/O devices to operate at speeds nearing the speed the CPU itself uses when commu- nicating with its own special components. This section covers some very technical items and it is strongly recommended that only experi- enced users should make any changes to the default settings.
  • Page 62 IRQ/DMA Resources When resources are controlled manually, assign each system interrupt a type. depending on the type of device using the interrupt. IRQ3/4/5/7/9/10/11/12/14/15 assigned to This item allows you to determine the IRQ assigned to the ISA bus and is not available to any PCI slot. Legacy ISA for devices compliant with the original PC AT bus specification, PCI/ISA PnP for devices compliant with the Plug and Play standard whether designed for PCI or ISA bus architecture.

  • Page 63: Pc Health Status

    PC Health Status Note: This screen will be shown up if optional features are available. CPU Warning Temperature Since the mainboard supports PCU temperature monitoring and over- heat alert. This item allows the user to set the threshold of CPU warning temperature.

  • Page 64: Frequency/Voltage Control

    Frequency/Voltage Control Auto Detect DIMM/PCI Clk This item allows you to enable/disable auto detect DIMM/PCIClock. Ø The choice: Enabled, Disabled. Spread Spectrum This item allows you to enable/disable the spread spectrum modulate. Ø The choice: Disabled, 0.25%, 0.5%. CPU Host /PCI Clock (CPU/PCI) This item allows the user to be over CPU Host Bus Clock from BIOS when JP14 jumper is set to Default.

  • Page 65: Load Fail-Safe Defaults

    Load Fail-Safe Defaults When you press <Enter> on this item you get a confirmation dialog box with a message similar to: Load Fail-Safe Defaults (Y/N) ? N Pressing 'Y' loads the BIOS default values for the most stable, minimal-performance system operations. Load Optimized Defaults When you press <Enter>...

  • Page 66: User Password Setting

    User Password Setting You can set either supervisor or user password or both of them. The defferencecs between are: Supervisor Password and User Setting The options on the Password screen menu make it possible to restrict access to the Setup program by enabling you to set passwords for two different access modes: Supervisor mode and User mode.
  • Page 67 Password Disable If you select System at Security Option of BIOS Features Setup Menu, you will be prompted for the password every time the system is rebooted or any time you try to enter Setup. If you select Setup at Security Option of BIOS Features Setup Menu, you will be prompted only when you try to enter Setup.

  • Page 68: Save & Exit Setup

    Save & Exit Setup Pressing <Enter> on this itemc, below dialog shows up and asks you for confirmation : Save to CMOS and EXIT (Y/N)? Y Pressing "Y" stores the selections made in the menus in CMOS - a special section of memory that stays on after you turn your system off. The next time you boot your computer, the BIOS configures your system according to the Setup selections stored in CMOS.

Table of Contents