Download
Share
Print this page
Chauvin Arnoux AEMC Instruments OX5042 Instructions Manual
  1. Manuals
  2. Brands
  3. Chauvin Arnoux Manuals
  4. Measuring Instruments
  5. AEMC Instruments OX5042
  6. Instructions manual

Chauvin Arnoux AEMC Instruments OX5042 Instructions Manual

Handscope
Hide thumbs
1
2
3
4
5
6

Advertisement

Quick Links

Download this manual
Model OX5042 Handscope
Instructions for General
Electrical Measurements
First-Time Setup
1. Turn the instrument ON.
2. Press Scope Mode
3. Press Channel A
screen (default settings):
4. Press Channel B
5. Press the right navigation key
default this is set to x1.
6. Press the down navigation key
7. Press Enter
8. Press
9. Press
10. Press
to save the setting. The main menu now appears as follows:
NOTE: These settings will remain in effect (even if the instrument batteries are drained or
removed) until changed by the user.
11.
Apply the voltage to be measured to Channel A and current to Channel B.
12.
Press the Auto Set
Instruments • (800) 343-1391 • www.aemc.com
AEMC
®
.
. The main menu appears as follows at the bottom of the
.
to save the setting.
to highlight the Units field.
to highlight the A setting.
button to properly scale the measurements.
until the Multiplier field is highlighted. By
until the x1000 setting is highlighted.
99-MAN 100453v4
1

Advertisement

loading

Related Manuals for Chauvin Arnoux AEMC Instruments OX5042

Summary of Contents for Chauvin Arnoux AEMC Instruments OX5042

  • Page 1 Model OX5042 Handscope Instructions for General Electrical Measurements First-Time Setup 1. Turn the instrument ON. 2. Press Scope Mode 3. Press Channel A . The main menu appears as follows at the bottom of the screen (default settings): 4. Press Channel B 5.

  • Page 2: Ac Voltage Measurement

    AC Voltage Measurement 1. Attach the BNC adapter (shown on right) to the Channel A input. 2. Attach the 10’ black and red leads to the adapter. 3. Select the alligator or pencil tip probes and attach them to the leads as needed.

  • Page 3: Ac Current Measurement

    AC Current Measurement 1. Select the current probe based on the current to be measured: • MN251T for measuring from 1 – 200A • MiniFlex sensor for measuring 10 – 3000A. 2. Attach the current probe to the Channel B input. 3.
  • Page 4 AC Current Harmonics 1. Set up the instrument for current measurement, as instructed by steps 1 through 6 of the “AC Current Measurement” section above. 2. Press Harmonics Mode . The THD (Total Harmonics Distortion) percentage appears in the upper right corner on the Channel B display (see the example below) 3.
  • Page 5 Millivolt Drop 1. Set up the instrument for voltage measurement, as instructed by steps 1 through 6 of the “AC Voltage Measurement” section above. 2. Press Channel A 3. Use the Attenuate Range key to set units in the mV range. The millivolt drop for the test point appears on the Channel A display (see the example below) 4.
  • Page 6 Tel: +961 1 890 425 - Fax: +961 1 890 424 ITALIA - Amra SpA USA - Chauvin Arnoux Inc - d.b.a AEMC Instruments Via Sant’Ambrogio, 23/25 - 20846 Macherio (MB) Tel: +39 039 245 75 45 - Fax: +39 039 481 561 15 Faraday Dr.

This manual is also suitable for:

Aemc instruments ox5042-ck