Table of Contents
Advertisement
Quick Links
5 MP ColorVu PoC Camera
User Manual
Thank you for purchasing our product. If there are any
questions, or requests, do not hesitate to contact the
dealer.
This manual applies to the models below:
Type I Camera
Type II Camera
Type III Camera
This manual may contain several technical mistakes or
printing errors, and the content is subject to change
without notice. The updates will be added to the new
version of this manual. We will readily improve or
update the products or procedures described in the
manual.
Type
User Manual
Model
DS-2CE10HFT-E
DS-2CE12HFT-E
DS-2CE72HFT-E
01000020200720
Advertisement
Table of Contents
Related Manuals for HIKVISION DS-2CE10HFT-E
Summary of Contents for HIKVISION DS-2CE10HFT-E
- Page 1 This manual applies to the models below: Type Model Type I Camera DS-2CE10HFT-E Type II Camera DS-2CE12HFT-E Type III Camera DS-2CE72HFT-E This manual may contain several technical mistakes or printing errors, and the content is subject to change without notice.
- Page 2 The information contained in the Manual is subject to change, without notice, due to firmware updates or other reasons. Please find the latest version of this Manual at the Hikvision website (https://www.hikvision.com/). Please use this Manual with the guidance and assistance of professionals trained in supporting the Product.
- Page 3 UNSAFE NUCLEAR FUEL-CYCLE, OR IN SUPPORT OF HUMAN RIGHTS ABUSES. IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE LATER PREVAILS. Regulatory Information FCC Information Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
- Page 4 Warning This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. Safety Instruction These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss.
- Page 5 the surface of sensor will not be exposed to the laser beam. Do not expose the device to high electromagnetic radiation or extremely hot, cold, dusty or damp environment. To avoid heat accumulation, good ventilation is required for the operating environment. Keep the camera away from liquid while in use for ...
-
Page 6: Table Of Contents
TABLE OF CONTENTS 1 Introduction ................1 1.1 Product Features ............1 1.2 Overview ................. 1 1.2.1 Overview of Type I Camera ........ 1 1.2.2 Overview of Type II Camera ....... 1 1.2.3 Overview of Type III Camera ......1 2 Installation................ -
Page 7: Introduction
1 Introduction 1.1 Product Features The main features are as follows: High performance CMOS sensor OSD menu with configurable parameters 24-hour color image Smart light 3-axis adjustment Power over coaxial 1.2 Overview 1.2.1 Overview of Type I Camera Power Cord Video Cable Bracket... -
Page 8: Installation
2 Installation Before you start Make sure that the device in the package is in good condition and all the assembly parts are included. Make sure that all the related equipment is power-off during the installation. Check the specification of the products for the ... -
Page 9: Ceiling/Wall Mounting With Junction Box
Pan Position [0° to 360°] Rotation Position Bracket [0° to 360°] Adjusting Nut Tilt Position [0° to 90°] Figure 2-3 3-Axis Adjustment 2.1.2 Ceiling/Wall Mounting with Junction Box Before you start: You need to purchase a junction box in advance. Steps: 1. -
Page 10: Installation Of Type Ii Camera
Figure 2-7 Combine Junction Box Cover back to its Body 8. Repeat the step 5 to 6 of 2.1.1 Ceiling/Wall Mounting without Junction Box to finish the installation. 2.2 Installation of Type II Camera 2.2.1 Ceiling/Wall Mounting without Junction Box Before you start: The installation of ceiling mounting and wall mounting are similar. -
Page 11: Installation Of Type Iii Camera
Pan Position Rotation Position [0° to 360°] [0° to 360°] Trim Ring Tilt Position [0° to 180°] Screw A Screw B Figure 2-10 3-Axis Adjustment 1). Loosen the trim ring to adjust the pan position [0° to 360°]. 2). Loosen screw A to adjust the tilt position [0° to 180°]. -
Page 12: Ceiling/Wall Mounting With Junction Box
5. Attach the mounting base to the ceiling and secure it with supplied screws. For cement ceiling, you need to install wall plugs at first. Wall Plugs Screws Figure 2-14 Attach Mounting Base to Ceiling Note: The supplied screw package contains self-tapping screws and wall plugs. - Page 13 Figure 2-17 Drill Template Note: Drill the cable hole, when adopting ceiling outlet to route the cable. 3. Take apart the junction box, and align the screw holes of the mounting base with those on the junction box’s cover. 4. Install the mounting base to the junction box’s cover with three PM4 screws.
-
Page 14: Menu Description
3 Menu Description Please follow the steps below to call the menu. Note: The actual display may vary with your camera model. Steps: 1. Connect the camera with the TVI DVR, and the monitor, shown as the figure 3-1. Figure 3-1 Connection 2. -
Page 15: Video Format
1). Click up/down direction button to select the item. 2). Click Iris + to confirm the selection. 3). Click left/right direction button to adjust the value of the selected item. 3.1 VIDEO FORMAT You can set the video format to 5MP@20fps, 4MP@30fps, 4MP@25fps, 2MP@30fps or 2MP@25fps. - Page 16 VIDEO SETTINGS IMAGE MODE WHITE BALANCE BRIGHTNESS CONTRAST SHARPNESS SATURATION 3DNR MIRROR BACK EXIT SAVE & EXIT Figure 3-3 VIDEO SETTINGS IMAGE MODE IMAGE MODE is used to adjust the image saturation, and you can set it to STD (Standard) or HIGH-SAT (High Saturation).
-
Page 17: Smart Light
between two frames besides processing the noise in one frame. The noise will be much less and the video will be clearer. MIRROR OFF, H, V, and HV are selectable for mirror. OFF: The mirror function is disabled. H: The image flips 180° horizontally. V: The image flips 180°...