Table of Contents
Advertisement
Quick Links
Dual-Light Bullet & Turret Camera
User Manual
Thank you for purchasing our product. If there are any
questions, or requests, do not hesitate to contact the
dealer.
This manual applies to the models below:
Type I Camera
Type II Camera
Type III Camera
Type IV Camera
Type V Camera
This manual may contain several technical mistakes or
printing errors, and the content is subject to change
without notice. The updates will be added to the new
version of this manual. We will readily improve or
update the products or procedures described in the
manual.
Type
User Manual
Model
DS-2CE16K0T-LFS
DS-2CE16K0T-LPFS
DS-2CE16D0T-LFS
DS-2CE16D0T-LPFS
DS-2CE17K0T-LFS
DS-2CE17D0T-LFS
DS-2CE76K0T-LMFS
DS-2CE76D0T-LMFS
DS-2CE76K0T-LPFS
DS-2CE76D0T-LPFS
DS-2CE78K0T-LFS
DS-2CE78D0T-LFS
01000020220331
Advertisement
Table of Contents
Related Manuals for HIKVISION DS-2CE16K0T-LFS
Summary of Contents for HIKVISION DS-2CE16K0T-LFS
- Page 1 Thank you for purchasing our product. If there are any questions, or requests, do not hesitate to contact the dealer. This manual applies to the models below: Type Model DS-2CE16K0T-LFS DS-2CE16K0T-LPFS Type I Camera DS-2CE16D0T-LFS DS-2CE16D0T-LPFS DS-2CE17K0T-LFS Type II Camera...
- Page 2 With the philosophy of “Technology for the Good”, Hikvision requests that every end user of video technology and video products shall comply with all the applicable laws and regulations, as well as ethical customs, aiming to jointly create a better community.
- Page 3 establishing and constantly optimizing network security. Video products have made great contributions to the improvement of social security around the world, and we believe that these products will also play an active role in more aspects of social life. Any abuse of video products in violation of human rights or leading to criminal activities are contrary to the original intent of technological innovation and product development.
- Page 4 The information contained in the Manual is subject to change, without notice, due to firmware updates or other reasons. Please find the latest version of this Manual at the Hikvision website (https://www.hikvision.com/). Please use this Manual with the guidance and assistance of professionals trained in supporting the Product.
-
Page 5: Regulatory Information
UNSAFE NUCLEAR FUEL-CYCLE, OR IN SUPPORT OF HUMAN RIGHTS ABUSES. IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE LATTER PREVAILS. Regulatory Information FCC Information Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. - Page 6 Safety Instruction These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss. The precaution measure is divided into “Warnings” and “Cautions”. Warnings: Serious injury or death may occur if any of the warnings are neglected.
-
Page 7: Product Features
Do not aim the camera at the sun or extra bright places. The sensor may be burned out by a laser beam, so when any laser equipment is in using, make sure that the surface of sensor will not be exposed to the laser beam. -
Page 8: Installation
1.2.3 Overview of Type III Camera Base Set Screw Enclosure Main Body Switch Button Power Cord Video Cable Figure 1-3 Overview of Type III Camera Note: Press and hold the switch button for 5 seconds to switch the video output. Four kinds of video outputs are available: TVI, AHD, CVI, and CVBS. - Page 9 Installation of Type I & II Camera 2.1.1 Ceiling/Wall Mounting without Junction Box Steps: 1. Paste the drill template (supplied) to the installation location. 2. (Optional) For cement ceiling, drill the screw holes with a 5.5 mm drill and insert the supplied wall plugs.
- Page 10 Figure 2-4 Secure the Junction Box on the Wall 7. Route the cables through the bottom cable hole or side cable hole of the junction box and connect the cables. 8. Fix the junction box cover on its body with three PM3 ×...
- Page 11 Figure 2-7 Secure the Base to the Ceiling 6. Align the screw hole with the triangle mark to install the camera back to the base and secure it. Figure 2-8 Install the Camera Back 7. Connect the cables. 8. Power on the camera to check whether the image on the monitor is gotten from the optimum angle.
- Page 12 Figure 2-10 Secure the Junction Box Body 6. Route the cables through the bottom cable hole or the side cable hole of the junction box. 7. Combine the junction box cover with its body and secure it with three PM3 × 13 screws. Figure 2-11 Combine the Junction Box Cover and Body 8.
- Page 13 Figure 2-14 Fix the Wall Mount 3. Loosen the set screw. 4. Rotate the camera to align the triangle mark with the screw hole, and disassemble the camera. Figure 2-15 Dissemble the Camera 5. Use M4 × 10 screws to fix the base onto the wall mount.
- Page 14 Figure 2-18 Install the Camera to Ceiling 4. Connect the cables. 5. Power on the camera to adjust the view angle according to the figure below. Figure 2-19 3-Axis Adjustment 1). Rotate the enclosure to adjust the pan position [0° to 360°]. 2).
-
Page 15: Menu Description
Figure 2-21 Fix the Junction Box Cover and Junction Box Body 7. Route the cables through the bottom cable hole or the side cable hole of the junction box. 8. Refer to step 5 of 2.3.1 Ceiling Mounting without Junction Box to adjust the angle and finish the installation. - Page 16 Steps: 1. Connect the camera with the TVI DVR and the monitor, as shown in figure 3-1. Figure 3-1 Connection 2. Power on the camera, TVI DVR, and monitor to view the image on the monitor. 3. Click PTZ Control to enter the PTZ Control interface. 4.
-
Page 17: Video Format
3). Click left/right direction buttons to adjust the value of the selected option. 3.2 VIDEO FORMAT Video formats are available as below. Video Output Video Format 3K@20fps 4MP@25fps 4MP@30fps 2MP@25fps 2MP@30fps 5MP@20fps 4MP@25fps 4MP@30fps 4MP@25fps 4MP@30fps CVBS NTSC 3.3 EXPOSURE EXPOSURE MODE You can set the EXPOSURE MODE to GLOBAL, BLC, HLC, or DWDR. -
Page 18: White Light
set the value from 1 to 9. The larger the value is, the more sensitive the camera is. N D Threshold (Night to Day Threshold) Night to Day Threshold is used to control the sensitivity of switching the night mode to the day mode. You can set the value from 1 to 9. -
Page 19: Audio Settings
BRIGHTNESS Brightness refers to the brightness of the image. You can set the brightness value from 1 to 9 to darken or brighten the image. The greater the value is, the brighter the image is. CONTRAST This feature enhances the difference in color and light between parts of an image.