Smart Installation Guide. Declaration of Conformity Aqualisa Products Limited declares that the Aqualisa SmartValve and supplied controller, in conjunction with pairing remotes and diverter, complies with the essential requirements and other relevant provisions of the Low Voltage Directive (2014/35/EU), the EMC Directive (2014/30/EU) and the RED Directive (2014/53/EU).
GET SMART CONNECTED Unlock the potential of your shower; from water consumption analysis to enhanced user functions. Keep up to date with latest features for the Aqualisa app and voice activation by visiting the Aqualisa website. Download and open the free Aqualisa app. Find instructions on page 15 “Connecting to the App”.
Quick Start You can prepare your temperature and outlet before you switch on the shower, or adjust with ease while showering. WAKE UP, (POWER ON) SHOWER ON AND POWER OFF TEMPERATURE FLOW SELECT OUTLET* Adjust before or Adjust during Push and hold Q lever for over during showering.
Wake-up The controller has a proximity sensor, so as you approach or move your hand towards the controller, the display wakes up and is ready to go. (You can disable this feature in the Settings menu - see page 12). 0.5 metres The proximity sensor detects any object directly in front, at...
20 minutes. The flow can be stopped and started at any time by following the instruction on this page. This can be enhanced by activating and using the free Aqualisa app. See pages 3 and 15 for details.
Adjusting the Temperature From the Home screen you can adjust the temperature at any time, before or during showering, by turning the bezel. TIP: This is your Home screen. When in any of the Menu or Settings screens, you can easily return to the home screen by turning the temperature bezel.
Adjusting the Flow From the Home screen you can adjust the flow during showering, by moving the lever left or right.* FLOW FEEDBACK DISPLAY Flow Flow After adjusting the flow, the display will return to the temperature Home screen after a few seconds. Emergency Stop: When the flow setting is at ECO, joggle the Q lever down 3 times in succession to turn the shower off.
Selecting your Outlet Divert models only From the Home screen, you can alternate between outlets by pushing and holding the lever for over 3 seconds and releasing when the desired outlet icon appears. This can be done upon starting the shower, or during showering.
Adjustable Head Vita™ Head To avoid water dripping from the shower head after use, we advise to tilt the head back to allow residual water to drain out. The above recommendation applies to both adjustable and fixed shower heads. 1. Inner Rotate the spray plate lever clockwise or anticlockwise to select the desired spray pattern.
Page 11
Bath Overflow Filler 1. Push the waste cover to engage the plug fitting. 2. Push the waste cover again to disengage the plug. Do not leave the bath filler running unattended. Although the overflow will remove excess water once the bath is overfilled, this may not be sufficient to prevent the bath from overflowing (depending on system conditions).
Settings Optic Q™ features optional settings to enhance your shower. To enter Settings, from the Home Screen, move the lever left or right until the Settings screen appears. Push the lever to enter. Access to the settings menu is only available when water is not flowing.
Page 13
Auto Wake up required if you have a small shower enclosure, and the controller is permanently active. Factory default: ON. WIFI To connect to the Aqualisa app and enable shower functionality using Wifi your personal smart devices. PAIR A REMOTE...
Configuring your Outlets This setting enables you to choose the icons that represent your outlets. If you have multiple outlets, you can also Confi gure Outlets select the most commonly used, this is known as the primary outlet. Water will divert to this outlet unless you select otherwise.
Refer to the troubleshooting section of this guide for guidance and advice. The Aqualisa app utilises the Instabug platform; this tool can be used to: Report an issue, suggest an improvement, or ask a question. If you experience problems connecting your shower, or with the app functions, then an Instabug report can be raised.
Page 16
Following the instruction on the screen of the controller – push the lever to connect. Set up Shower - Wifi The Aqualisa app will direct you to the Wifi settings menu on your mobile device. From the list of available Networks select: QSVC XXXX The password is: SmartShower (case sensitive).
SMART SPEAKER SET-UP Once the Aqualisa app is set up and the shower connected, go to the app for your smart speaker and follow their instructions to add the Aqualisa home to your devices. The Aqualisa app gives you the capability to operate your product remotely using your mobile device.
Changing water system? If switching from a gravity-fed water system to a mains pressure system (e.g. Combination boiler) you will need to change your Aqualisa SmartValve . Contact a member of our Customer Service team for further information.
Check data cable connections are making good displaying communications contact and are fully inserted and that there “Preparing, please is no visible damage. Power reset the Aqualisa wait….” for longer SmartValve than 2 minutes Check that the wiring schematics are as per installation instructions in the Smart Installation Guide.
Page 20
(unless a separate stand alone pump is being utilised). Refer to the Smart Installation Guide. Water supply issue For the Standard Aqualisa SmartValve - Ensure water is turned fully on at the mains and at the servicing valve in the supply.
Page 21
Seasonal conditions In the warmer months, the mains water too hot temperature can rise to ambient level. The Aqualisa SmartValve always blends a mix of both hot and cold supplies therefore the output temperature at fully cold (controller setting) will always be higher than the incoming cold water supply.
Page 22
Settings menu Refer to Wiring Diagram Section in the Smart Installation Guide. Outlets not Turn off the power supply to the Aqualisa configured SmartValve , leave isolated for at least 2 minutes. Reinstate power supply and then...
SmartShower is entered correctly- you do not have to wait for connection confirmation, once QSVC has been selected wait a few seconds and then return to the Aqualisa app. Ensure that you are keying your SSID (home Wifi) and password correctly.
You can easily increase your FREE guarantee to 5 years simply by registering your product. Please keep your receipt to validate your guarantee. Please see our website for full terms and conditions. *Subject to terms and conditions Register your guarantee instantly at aqualisa.co.uk/guarantee Register your guarantee 0800 408 4243...
01959 560010 Use Live Chat at aqualisa.co.uk Or email us at enquiries@aqualisa.co.uk Instabug reporting platform for the Aqualisa app. Accessed in the app by: Shaking your phone or tapping on the message bubble. See page 15 for details.
Page 28
Please note that calls may be recorded for training and quality purposes. The company reserves the right to alter, change or modify the product specifications without prior warning. ® Registered Trademark Aqualisa Products Limited. Q5285 Part No 705145 Issue 03 - Dec 20...
Need help?
Do you have a question about the OPTIC Q and is the answer not in the manual?
Questions and answers