Advertisement
12
Manual
The reference is the value at which it will start to
open when the value of the sensor is superior to this
one.
It will close when the value of the sensor is
inferior to the value of the reference minus the
differential.
When it is at open or close, some timings take
place so that the climatic changes, produced on
moving the windows, are taken correctly by the
sensors.
First the pauses of open or close take place and
then the timings of open and close and they will be
repeated when the value of the sensor has to open or
close.
The timings can be programmed up to 99
seconds and the pauses up to 999.
6.2. CURVES
The curve of every programme is an important
feature that the programme has and that can be very
useful in applications such as the automatic increase
and/or
decrease
of
modification of the time of lighting, etc.
To enter in the curves of every one of the
programmes, press the key "FUN" and choose option
2, and it will ask for the number of programme.
F1:
Programmes
F2:
Curves
Num of programme= 00
(for curves)
Every programme has a curve, except the types
4-5-7-8-9, in which there is a seond curve that contains
the maximum and minimum values of outlet. For this
reason, it asks, in these types, to which of the two
curves we want to access.
P02
VENT-1
Once the number of curve is entered, it will ask
for the position and the reference of the first point out
of the four that each curve contains. At the right of the
number of curve it shows us the point which is asking.
P02
VENT-1
Pos=000
Every point has a value of situation in the time,
in days, and some values of reference according to the
type of working.
The curves can be compared with patterns
which are used by the programmes in order to do a
variable and automatic control.
(Yes/No)= No
temperature,
the
automatic
C0
C1 Point1
Ref= 00.0 ºC
Here we can see a simple example.
P02
HEAT-1
Pos=003
Pos=008
Pos=020
Pos=045
This curve would control the temperature as the
animal grows, for example.
Every point corresponds to days of growth and
the reference of temperature will change in the values
that correspond within these points.
We have to say that if point 1 does not
correspond to 0 days, the value of reference that the
programme will take will be fix, until reaching the
position of point 1; in the example the first three days
of reference will be 29.8 ºC.
The same happens from the fourth point; in the
example after 45 days the value will stay at 20.0ºC.
6.3. RECORD
The record is an statistical record of the last
seven days, for everyone of the programmes.
To acced to the record of every programme,
press the key "FUN" and choose option 3, and it will
ask for the number of programme.
F3:
Record
F4:
Anomalies
Num. of programme= 00
(for record)
Once the number is entered, it will show today's
record. To see the previous six days, press the key
with arrow.
To see another programme, press the key
"ENTER". To escape press the keys "FUN" or "CON".
In the upper line of the record it shows at the
left, the text of the programme, in the center, the day
and month and at the right the hours and minutes in
which the programme has been working if the outlet is
by relay (type 6 no). If it is analogical (types 4 -5) or
proportional (types 7-8-9) outle, it shows the average
of the day of the percentage of the value of the outlet.
At the lower line, at the left, it shows the highest
value of reading of the sensor, at the center the
average of all the readings of the day, and at the right
the lowest one.
TERM-1
20.2
19.6
For the reading of the accumulated values in
every
one
of
the
configurated as such) enter in the function of Record.
C1 Point1
Ref= 29.8 ºC
Ref= 27.5 ºC
Ref= 25.0 ºC
Ref= 20.0 ºC
21/08 (04:48)
18.4 ºC
inputs/counters
(if
they
are
Advertisement
