Page 1
Valued Customer, We are pleased that you have chosen to purchase an electric fireplace manufactured by Dimplex North America Ltd. Over the years, valuable memories will occur around the warmth and comfort of your hearth. Thank you for allowing our product to be the backdrop for those special moments.
OPERATION MANUAL CONTROLS (WITHOUT REMOTE OPTION) PURIFIRE The fireplace can be controlled by the manual SWITCH switches located on the fireplace (FIGURE 1). Main Power Switch Main ON/OFF switch, activates the flame effect. Heater Control Switch Heater ON/OFF switch, activates heater to the high level.
Page 4
BF33STP, BF33DXP, BF39STP, BF39DXP REMOTE CONTROL The remote control has a range of approximately 50ft. (15.25m). It does not have to be pointed at the fireplace and can pass through most obstacles (including walls). It is supplied with one of 243 independent frequencies to prevent interference with other units.
Page 5
BF33STP, BF33DXP, BF39STP, BF39DXP RESETTING THE TEMPERTURE CUTOUT SWITCH The heater on this fireplace is protected with a safety device to prevent overheating. Should the heater overheat, a red light (Fig. 4) will be activated and an automatic cut out will turn the heater off. The heater will re-activate once the heater has cooled. The overheat cutout will be triggered if the filter is dirty.
BF33STP, BF33DXP, BF39STP, BF39DXP If the fireplace was operating prior to servicing allow at least 10 minutes for light bulbs and heating elements to cool off to avoid accidental burning of skin. Disconnect circuit power before attempting any maintenance or cleaning to reduce the risk of electric shock or damage to persons.
BF33STP, BF33DXP, BF39STP, BF39DXP If the fireplace was operating prior to servicing allow at least 10 minutes for light bulbs and heating elements to cool off to avoid accidental burning of skin. Disconnect circuit power before attempting any maintenance or cleaning to reduce the risk of electric shock or damage to persons.
BF33STP, BF33DXP, BF39STP, BF39DXP If the fireplace was operating prior to servicing allow at least 10 minutes for light bulbs and heating elements to cool off to avoid accidental burning of skin. Disconnect circuit power before attempting any maintenance or cleaning to reduce the risk of electric shock or damage to persons.
BF33STP, BF33DXP, BF39STP, BF39DXP If the fireplace was operating prior to servicing allow at least 10 minutes for light bulbs and heating elements to cool off to avoid accidental burning of skin. Disconnect circuit power before attempting any maintenance or cleaning to reduce the risk of electric shock or damage to persons.
Page 13
BF33ST, BF33DX, BF39ST, BF39DX, BF45ST, BF45DX If the fireplace was operating prior to servicing allow at least 10 minutes for light bulbs and heating elements to cool off to avoid accidental burning of skin. Disconnect circuit power before attempting any maintenance or cleaning to reduce the risk of electric shock or damage to persons.
BF33STP, BF33DXP If the fireplace was operating prior to servicing allow at least 10 minutes for light bulbs and heating elements to cool off to avoid accidental burning of skin. Disconnect circuit power before attempting any maintenance or cleaning to reduce the risk of electric shock or damage to persons.
Page 15
BF33STP, BF33DXP If the fireplace was operating prior to servicing allow at least 10 minutes for light bulbs and heating elements to cool off to avoid accidental burning of skin. Disconnect circuit power before attempting any maintenance or cleaning to reduce the risk of electric shock or damage to persons.
Page 16
BF33STP, BF33DXP, BF39STP, BF39DXP If the fireplace was operating prior to servicing allow at least 10 minutes for light bulbs and heating elements to cool off to avoid accidental burning of skin. Disconnect circuit power before attempting any maintenance or cleaning to reduce the risk of electric shock or damage to persons.
BF33STP, BF33DXP, BF39STP, BF39DXP If the fireplace was operating prior to servicing allow at least 10 minutes for light bulbs and heating elements to cool off to avoid accidental burning of skin. Disconnect circuit power before attempting any maintenance or cleaning to reduce the risk of electric shock or damage to persons.
Page 18
BF33STP, BF33DXP, BF39STP, BF39DXP If the fireplace was operating prior to servicing allow at least 10 minutes for light bulbs and heating elements to cool off to avoid accidental burning of skin. Disconnect circuit power before attempting any maintenance or cleaning to reduce the risk of electric shock or damage to persons.
BF33ST, BF33DX If the fireplace was operating prior to servicing allow at least 10 minutes for light bulbs and heating elements to cool off to avoid accidental burning of skin. Disconnect circuit power before attempting any maintenance or cleaning to reduce the risk of electric shock or damage to persons.
Page 20
14. Using a sharp utility knife, cut 3.22” off of the length of the rubber channel so the overall length is 17.33”. 15. Reassemble in the reverse order as above. NOTE: To replace the log set re-connect the logset LED wire harness to the unit, insert the front edge, pushing back down until the rear tab snaps under the back ledge and the logs are resting against the mirror.
Page 21
BF39STP, BF39DXP If the fireplace was operating prior to servicing allow at least 10 minutes for light bulbs and heating elements to cool off to avoid accidental burning of skin. Disconnect circuit power before attempting any maintenance or cleaning to reduce the risk of electric shock or damage to persons.
Page 22
BF33STP, BF33DXP, BF39STP, BF39DXP If the fireplace was operating prior to servicing allow at least 10 minutes for light bulbs and heating elements to cool off to avoid accidental burning of skin. Disconnect circuit power before attempting any maintenance or cleaning to reduce the risk of electric shock or damage to persons.
BF33STP, BF33DXP If the fireplace was operating prior to servicing allow at least 10 minutes for light bulbs and heating elements to cool off to avoid accidental burning of skin. Disconnect circuit power before attempting any maintenance or cleaning to reduce the risk of electric shock or damage to persons.
Page 24
BF39STP, BF39DXP If the fireplace was operating prior to servicing allow at least 10 minutes for light bulbs and heating elements to cool off to avoid accidental burning of skin. Disconnect circuit power before attempting any maintenance or cleaning to reduce the risk of electric shock or damage to persons.
Page 25
WARNING: Ensure wires do not come in contact with moving parts by securing wires in tie wraps. BF39ST, BF39DX, BF45ST, BF45DX If the fireplace was operating prior to servicing allow at least 10 minutes for light bulbs and heating elements to cool off to avoid accidental burning of skin. Disconnect circuit power before attempting any maintenance or cleaning to reduce the risk of electric shock or damage to persons.
Page 26
BF33ST, BF33DX, BF39ST, BF39DX, BF45ST, BF45DX If the fireplace was operating prior to servicing allow at least 10 minutes for light bulbs and heating elements to cool off to avoid accidental burning of skin. Disconnect circuit power before attempting any maintenance or cleaning to reduce the risk of electric shock or damage to persons.
BF33ST, BF33DX, BF39ST, BF39DX, BF45ST, BF45DX If the fireplace was operating prior to servicing allow at least 10 minutes for light bulbs and heating elements to cool off to avoid accidental burning of skin. Disconnect circuit power before attempting any maintenance or cleaning to reduce the risk of electric shock or damage to persons.