Related Manuals for Dimplex BF33ST/DX
Summary of Contents for Dimplex BF33ST/DX
- Page 1 INSTALLATION GUIDE FOR THE ELECTRIC FIREPLACE MODEL NUMBERS: BF33ST/DX BF39ST/DX BF45ST/DX 7206350200REV06...
-
Page 2: Table Of Contents
CONTENTS PAGE 1 PAGE 1 PAGE 1 PAGE 2 PAGE 2 PAGE 2 PAGE 3 PAGE 3 PAGE 4 PAGE 5 PAGE 6 - 7 PAGE 8 - 9 PAGE 10 - 11 PAGE 12 - 13 PAGE 14 - 15 PAGE 16 - 18 Listings and Code Approvals Model Specifications... -
Page 3: Section A
LISTINGS AND CODE APPROVALS The BF series fireplaces have been tested in accordance with the UL 2021 and CSA C22.2 No. 46 standards for fixed and location-dedicated electric room heaters. MODEL SPECIFICATIONS Model Description Voltage Volts Number 33” 120/120/208/ BF33ST Standard 120/120/208/ BF33DX... -
Page 4: Framing
WARNING Ensure method of installation does NOT obscure the air intake slots on bottom front of unit in any manner. (see diagram in Section A) SECTION A: FRAMING MODEL BF33ST/DX 15.0” 33.5” BF39ST/DX 16.0” 39.5” BF45ST/DX 16.0” 45.5” Rough-in framing dimensions This fireplace is a zero clearance design. -
Page 5: Voltage Selector Switch Location
VOLTAGE SELECTOR SWITCH LOCATION IMPORTANT: Ensure that the incoming power supply voltage matches the setting of the voltage selector switch. NOTE: The voltage selector switch is located inside the exhaust panel on the top right hand corner. CAUTION: When changing the voltage selector switch from 240 volts to 120 volts ensure that the power supply is turned off. -
Page 6: Section C
SECTION C: FACTORY SETTING WIRING (WITHOUT MAIN POWER WALL SWITCH) IMPORTANT: The unit is factory configured for 208/240 volt operation NOTE: Use 3 conductor wire with ground (4 wires total) from the power supply (breaker panel) to the junction box on the unit. NOTE: All wiring must be completed prior to installing the unit. -
Page 7: (Without Main Power Wall Switch)
SECTION C: FACTORY SETTING WIRING (WITHOUT MAIN POWER WALL SWITCH) IMPORTANT: The unit is factory configured for 208/240 volt operation NOTE: Use 2 conductor wire with ground (3 wires total) from the power supply (breaker panel) to the junction box on the unit. NOTE: All wiring must be completed prior to installing the unit. - Page 8 SECTION C: FACTORY SETTING WIRING (WITHOUT MAIN POWER WALL SWITCH) (NO HEAT INSTALLATION) IMPORTANT: The unit is factory configured for 208/240 volt operation NOTE: Use 2 conductor wire with ground (3 wires total) from the power supply (breaker panel) to the junction box on the unit.
-
Page 9: Section D
SECTION D: MAIN POWER WALL SWITCH WIRING OPTIONS MAIN POWER WALL SWITCH WIRING NOTE: This option should not be used with the remote control kit. NOTE: Before installing the unit you must have the following wires installed: 1. A 3 conductor wire with ground (4 wires total) from the power supply panel to the main switch wall box. - Page 10 240 VOLT MAIN WALL SWITCH WIRING DIAGRAM WHITE - N WHITE – N 240 V RED – L2 RED – L2 POWER SUPPLY WALL SWITCH BLACK – L1 BLACK – L1 (BREAKER PANEL) GROUND - G GROUND - G...
-
Page 11: Main Power Wall Switch Wiring For 120 Volt
MAIN POWER WALL SWITCH WIRING NOTE: This option should not be used with the remote control kit. NOTE: Before installing the unit have the following wires installed: 1. A 2 conductor wire with ground (3 wires total) from the power supply panel to the main switch wall box. - Page 12 120 VOLT MAIN WALL SWITCH WIRING DIAGRAM WHITE - N WHITE – N RED – L2 120 V POWER BLACK – L1 SUPPLY (BREAKER WALL PANEL) BLACK – L1 SWITCH GROUND - G GROUND - G...
- Page 13 MAIN POWER WALL SWITCH WIRING NOTE: This option should not be used with the remote control kit. NOTE: Before installing the unit have the following wires installed: 3. A 2 conductor wire with ground (3 wires total) from the power supply panel to the main switch wall box.
- Page 14 120 VOLT MAIN WALL SWITCH WIRING DIAGRAM NO HEAT INSTALLATION WHITE - N WHITE – N RED – L2 120 V POWER Wire Nut BLACK – L1 SUPPLY (BREAKER WALL BLACK – L1 PANEL) SWITCH GROUND - G GROUND - G...
-
Page 15: Section E
SECTION E: HEATER WALL SWITCH AND WALL THERMOSTAT WIRING OPTIONS HEATER WALL SWITCH WIRING NOTE: Before installing the unit complete the following: 1. Install main power connection with appropriate voltage as per Section C or Section D. 2. Install a 2 conductor wire with ground (3 wires total) from the heater switch wall box to the junction box on the unit. - Page 16 HEATER WALL SWITCH WIRING DIAGRAM FOR 120/240 VOLT (SEE SECTION C OR SECTION D FOR MAIN POWER CONNECTION) RED – 2 WALL RED – 1 SWITCH GROUND - G...
-
Page 17: Wall Mounted Thermostat Wiring For 120/240 Volt
WALL MOUNTED THERMOSTAT WIRING NOTE: Before installing the unit complete the following: 1. Install main power connection with appropriate voltage as per Section C or Section D. 2. Install a 2 conductor wire with ground (3 wires total) from the thermostat wall box to the junction box on the unit. -
Page 18: Wiring Diagrams
WALL MOUNTED THERMOSTAT WIRING DIAGRAM FOR 120/240 VOLT (SEE SECTION C OR SECTION D FOR MAIN POWER CONNECTION) CONNECT GROUND TO WALL BOX RED – 2 WALL RED – 1 THERMOSTAT GROUND - G... -
Page 19: Flame Override Switch Wiring For 120/240 Volt
FLAME OVERRIDE SWITCH WIRING NOT AVAILABLE WITH NO HEAT INSTALLATION NOTE: The fireplace can be wired to have a wall switch operate the heater independent of the flame NOTE: Before installing the unit complete the following: 1. Install main power connection with appropriate voltage as per Section C or Section D. - Page 20 FLAME OVERRIDE WALL SWITCH WIRING DIAGRAM FOR 120/240 VOLT (SEE SECTION C OR SECTION D FOR MAIN POWER C0NNECTION) NOT AVAILABLE WITH NO HEAT INSTALLATION BLUE – 4 WALL BLUE – 3 SWITCH GROUND - G...
-
Page 21: Wiring Diagram Lower Section
WIRING DIAGRAM LOWER SECTION BROWN WHITE BLACK BLUE (3) MARR BLACK RED (1) WHITE WHITE (N) BLUE (4) RED (2) BLACK RED (L2) -
Page 22: Wiring Diagram Upper Section
WIRING DIAGRAM UPPER SECTION... -
Page 23: Wiring Schematic
WIRING SCHEMATIC... - Page 24 1-888-DIMPLEX 1-888-346-7539 1367 Industrial Road Cambridge, Ontario Canada, N1R 7G8 Approved for use in the United States and Canada...
Need help?
Do you have a question about the BF33ST/DX and is the answer not in the manual?
Questions and answers