Texas Instruments TUSB3210 User Manual
Generic evaluation board
Hide thumbs
Also See for TUSB3210:
- Data manual (44 pages) ,
- User manual (22 pages) ,
- User manual (19 pages)
Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Texas Instruments TUSB3210
Summary of Contents for Texas Instruments TUSB3210
- Page 1 TUSB3210 Generic Evaluation Board User’s Guide 2005 MSP USB SLLU031A...
- Page 2 TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions:...
- Page 3 EVM IMPORTANT NOTICE Texas Instruments (TI) provides the enclosed product(s) under the following conditions: This evaluation kit being sold by TI is intended for use for ENGINEERING DEVELOPMENT OR EVALUATION PURPOSES ONLY and is not considered by TI to be fit for commercial use. As such, the goods being provided may not be complete in terms of required design-, marketing-, and/or manufacturing-related protective considerations, including product safety measures typically found in the end product incorporating the goods.
- Page 4 EVM schematic located in the EVM User’s Guide. When placing measurement probes near these devices during operation, please be aware that these devices may be very warm to the touch. Mailing Address: Texas Instruments Post Office Box 655303 Dallas, Texas 75265 Copyright 2005, Texas Instruments Incorporated...
- Page 5 Preface Read This First About This Manual This user’s guide describes the setup and operation of the TUSB3210 generic evaluation board. Familiarity with universal serial bus (USB) protocol and common laboratory testing equipment is required and assumed throughout this user’s guide.
- Page 6 Trademarks Trademarks MacOS is a trademark of Apple Computer, Inc. Windows and Windows ME are trademarks of Microsoft Corporation. Other trademarks are the property of their respective owners FCC Warning This equipment is intended for use in a laboratory test environment only. It gen- erates, uses, and can radiate radio frequency energy and has not been tested for compliance with the limits of computing devices pursuant to subpart J of part 15 of FCC rules, which are designed to provide reasonable protection...
-
Page 7: Table Of Contents
........... 1−3 TUSB3210 EVM Connected to a Compact Flash Daughterboard .... - Page 8 viii...
-
Page 9: Hardware And Software Required
Chapter 1 Hardware and Software Required The TUSB3210 generic EVM is designed for use with a personal computer running a USB-enabled operating system. The PC should be USB 1.1 specification compliant. This implies that the BIOS, chipsets, and operating system are all USB 1.1 specification compliant. If the BIOS is not specification compliant, the system may not boot up when USB devices are connected at power up, and the EVM may not function. -
Page 10: Equipment
This EVM is generic in the sense that it provides a 50-pin connector that allows access to the GPIO pins of the TUSB3210. It is meant to be used with another application-specific daughterboard that connects to the 50-pin connector. An example of such a daughterboard is shown in Figure 1−3. -
Page 11: Tusb3210 Evaluation Board
Running Title—Attribute Reference TUSB3210 device. A USB cable should be plugged into a USB port on a PC or into a USB hub and connected to the TUSB3210 EVM type-B connector (U3). Figure 1−2. TUSB3210 Evaluation Board Figure 1−3. TUSB3210 EVM Connected to a Compact Flash Daughterboard... -
Page 12: Tusb3210 Printed-Circuit Board (Rev 1.1)-Top Side
Running Title—Attribute Reference Figure 1−4. TUSB3210 Printed-Circuit Board (REV 1.1)—Top Side... -
Page 13: Tusb3210 Printed-Circuit Board (Rev 1.2)-Top Side
Running Title—Attribute Reference Figure 1−5. TUSB3210 Printed-Circuit Board (REV 1.2)—Top Side Chapter Title—Attribute Reference... -
Page 14: Bill Of Materials
Resistor, 1 MΩ S2, S1 Short TP1, TP2, TP3, TP4, TP5, TP6, TP7 Test point Jumper, TPS76333DBV Jumper. JP(3) Type-B USB shield USB controller, TUSB3210 MAX232 (REV 1.1 board) MAX3232 (REV 1.2 board) Eight-pin socket for 24LCxx 12 MHz SE3409-ND... -
Page 15: Schematic Diagram
Running Title—Attribute Reference 1.4 Schematic Diagram The complete schematic diagram of the TUSB3210 generic EVM is presented at the end of this document. Chapter Title—Attribute Reference... -
Page 17: Evm Operation
Chapter 2 EVM Operation This chapter describes the operation of the TUSB3210 EVM. Topic Page TUSB3210 Setup .......... -
Page 18: Tusb3210 Setup
USB-capable operating system. If necessary, configure the EVM based on the desired settings specified later in this section. Use a standard USB cable to connect the TUSB3210 EVM to a downstream port on the PC or to a USB HUB tier. -
Page 19: Eeprom
It enumerates properly when connected to a USB host. 2.7 GPIO Connector The 50-pin GPIO connector provides access to the TUSB3210 GPIOs as well as some other control signals. Figure 2−1 shows the signals available on the connector. -
Page 20: Gpio Connector
Running Title—Attribute Reference Figure 2−1. GPIO Connector P0.0 P0.1 P0.2 P0.3 P0.4 P0.5 P0.6 P0.7 P1.1 P1.0 P1.3 P1.2 P1.4 P1.5 P1.6 P1.7 P2.0 P2.1 P2.3 P2.2 P2.4 P2.5 P2.6 P2.7 P3.0 P3.1 P3.2 P3.3 P3.4 P3.5 P3.6 P3.7 SCL1 SUSP 3.3 Susp 1.8 V... - Page 21 P3.7 GND1 P3.7 22pF 22pF GND2 22pF 100K 1 +3.3V GND3 GND4 R10 100K 1 P3.0 TUSB3210 [If S2 or S3 tied to ground, remove (P3.0) 100K pull-up to save power] P3.1 (P3.1) R1IN R1OUT +3.3V R2IN R2OUT T1IN T1OUT...
- Page 22 +3.3V RST# +3.3V +3.3Susp PWR232 +3.3V +3.3Susp 0.1uF 1.2K MAX3232 RESET1 0.1uF 0.1uF +3.3V SW PUSHBUTTON 8pin Socket for 24LCxx JUMPER base1.dsn RUN(red) Title SUSP TUSB3210 GEN EVM (REV1.2) SUSP Size Document Number <Doc> Date: Wednesday, July 13, 2005 Sheet...
Need help?
Do you have a question about the TUSB3210 and is the answer not in the manual?
Questions and answers