Download Print this page
Texas Instruments TUSB8044RGC User Manual

Texas Instruments TUSB8044RGC User Manual

Evaluation module

Advertisement

Quick Links

TI's TUSB8044RGC evaluation module (EVM) is a functional board design that implements both a USB
3.0 hub and a USB 2.0 hub. The EVM can support both USB SuperSpeed (SS) and USB 2.0 high-speed
(HS), full-speed (FS), or low-speed (LS) operation on its USB ports. The EVM enumerates a Billboard
device on a virtual downstream port for USB Type-C™ applications with alternate mode support. It has an
2
I
C Master controllable through an HID-compliant device enumerated on a virtual downstream port. This
EVM is intended for use in evaluating system compatibility, developing optional EEPROM firmware, and
validating interoperability. This EVM also acts as a hardware reference design for any implementation of
the TUSB8044.
...................................................................................................................
1
Introduction
2
Hardware Overview
3
Hardware Setup
Appendix A
TUSB8044RGC REVD EVM Bill of Materials
Appendix B
TUSB8044RGC REVD EVM Schematics
1
TUSB8044RGC EVM Top Layer Layout
2
TUSB8044RGC REVD EVM Top Layer Layout
3
USB Port Connections
........................................................................................................................
4
Power
1
Switch Definitions
2
TUSB8044 QFN Lab EVM Bill Of Materials: Texas Instruments, CCI and ICP
Trademarks
Microsoft, Windows are registered trademarks of Microsoft Corporation.
USB Type-C is a trademark of USB Implementer's Forum.
All other trademarks are the property of their respective owners.
SLLU261A – April 2017 – Revised February 2019
Submit Documentation Feedback
TUSB8044RGC Evaluation Module
..........................................................................................................
..............................................................................................................
List of Figures
.................................................................................
.....................................................................................................
............................................................................................................
Copyright © 2017–2019, Texas Instruments Incorporated
SLLU261A – April 2017 – Revised February 2019
Contents
...................................................................
.......................................................................
.........................................................................
List of Tables
User's Guide
.....................................
TUSB8044RGC Evaluation Module
2
3
5
7
9
2
9
10
11
5
7
1

Advertisement

loading
Need help?

Need help?

Do you have a question about the TUSB8044RGC and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Texas Instruments TUSB8044RGC

  • Page 1 SLLU261A – April 2017 – Revised February 2019 TUSB8044RGC Evaluation Module TI's TUSB8044RGC evaluation module (EVM) is a functional board design that implements both a USB 3.0 hub and a USB 2.0 hub. The EVM can support both USB SuperSpeed (SS) and USB 2.0 high-speed (HS), full-speed (FS), or low-speed (LS) operation on its USB ports.
  • Page 2 NOTE: The EVM accommodates various lab test components; actual production implementations can be much smaller. Figure 1 illustrates the TUSB8044RGC EVM top layer layout. Figure 1. TUSB8044RGC EVM Top Layer Layout TUSB8044RGC Evaluation Module SLLU261A – April 2017 – Revised February 2019 Submit Documentation Feedback Copyright ©...
  • Page 3 A production implementation could place stricter limits on this power consumption. An overcurrent event on any of the downstream port connectors will be reported to the TUSB8044 through the OVERCURxZ inputs. SLLU261A – April 2017 – Revised February 2019 TUSB8044RGC Evaluation Module Submit Documentation Feedback Copyright © 2017–2019, Texas Instruments Incorporated...
  • Page 4 The switches (SW1, SW2, and SW3) and headers (J7, J8, J9) present on the TUSB8044 EVM are intended only for lab evaluation and are not required for production designs. TUSB8044RGC Evaluation Module SLLU261A – April 2017 – Revised February 2019 Submit Documentation Feedback Copyright © 2017–2019, Texas Instruments Incorporated...
  • Page 5 If SMBus is selected and stsOutputEn bit is set, ths pin will function as an SS_UP (upstream SS connection indicator). When enabled, a value of '1' indicates the upstream port is connected to a SuperSpeed USB capable port. SLLU261A – April 2017 – Revised February 2019 TUSB8044RGC Evaluation Module Submit Documentation Feedback Copyright © 2017–2019, Texas Instruments Incorporated...
  • Page 6 Make sure shunts are installed on J7, J8, and J9. • In the case where a 12-V power supply has been attached to the EVM, the fault is non-recoverable. TUSB8044RGC Evaluation Module SLLU261A – April 2017 – Revised February 2019 Submit Documentation Feedback Copyright © 2017–2019, Texas Instruments Incorporated...
  • Page 7 Appendix A SLLU261A – April 2017 – Revised February 2019 TUSB8044RGC REVD EVM Bill of Materials This appendix contains the TUSB8044RGC REVD EVM BOM. Table 2. TUSB8044 QFN Lab EVM Bill Of Materials: Texas Instruments, CCI and ICP Item Reference Part...
  • Page 8 Appendix A www.ti.com Table 2. TUSB8044 QFN Lab EVM Bill Of Materials: Texas Instruments, CCI and ICP (continued) Item Reference Part Manufacturer Part Number Description R4,R5,R11,R12,R Rohm MCR01MZPJ102 RES 1.0K OHM 1/16W 5% 0402 SMD 13,R14,R22,R23, Semiconductor R24,R25,R38,R39 ,R46, R47, R48...
  • Page 9 0.1uF 10uF 0.001uF 0.01uF 0.1uF Copyright © 2017, Texas Instruments Incorporated Figure 2. TUSB8044RGC REVD EVM Top Layer Layout SLLU261A – April 2017 – Revised February 2019 TUSB8044RGC REVD EVM Schematics Submit Documentation Feedback Copyright © 2017–2019, Texas Instruments Incorporated...
  • Page 10 USB3_TYPEA_CONNECTOR USB3_TYPEA_CONNECTOR 0.1uF 0.001uF 0.1uF 0.001uF 0402 0402 Copyright © 2017, Texas Instruments Incorporated Figure 3. USB Port Connections TUSB8044RGC REVD EVM Schematics SLLU261A – April 2017 – Revised February 2019 Submit Documentation Feedback Copyright © 2017–2019, Texas Instruments Incorporated...
  • Page 11 PWRON4_BATEN4 PWRON4_BATEN4 10uF TPS74801RGW 4.99K TPS2001C 0402 0.1uF 150uF 0402 Copyright © 2017, Texas Instruments Incorporated Figure 4. Power SLLU261A – April 2017 – Revised February 2019 TUSB8044RGC REVD EVM Schematics Submit Documentation Feedback Copyright © 2017–2019, Texas Instruments Incorporated...
  • Page 12 NOTE: Page numbers for previous revisions may differ from page numbers in the current version. Changes from Original (April 2017) to A Revision ......................Page ............................... • Revision History SLLU261A – April 2017 – Revised February 2019 Submit Documentation Feedback Copyright © 2017–2019, Texas Instruments Incorporated...
  • Page 13 TI products. TI’s provision of these resources does not expand or otherwise alter TI’s applicable warranties or warranty disclaimers for TI products. TI objects to and rejects any additional or different terms you may have proposed. IMPORTANT NOTICE Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2022, Texas Instruments Incorporated...

This manual is also suitable for:

Tusb8044rgcevm