Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Heatmiser DT-ETS WiFi RF
Summary of Contents for Heatmiser DT-ETS WiFi RF
- Page 1 Model: DT-ETS WiFi RF Model: DT-ETS WiFi RF...
-
Page 2: Table Of Contents
Model: DT-ETS WiFi RF Table Of Contents Locking the Keypad Product Image Table of Contents Temperature Control What is a Room Thermostat? Frost Protection Installation Procedure Heating ON/OFF LCD Display Optional Features Explained 21-22 WiFi Setup 9-11 Adjusting the Optional Settings... -
Page 3: Model: Dt-Ets Wifi Rf
The best way to do this is to set the room thermostat to a low temperature – say 18°C , Please read the instructions fully to understand all of the features of this DT-ETS WiFi RF and then turn it up by 1°C each day until you are comfortable with the temperature. You thermostat. -
Page 4: Installation Procedure
Terminate the thermostat as shown in the diagrams on pages 28-29 of this booklet. Step 3 Screw the thermostat back plate securely into the back box. Step 4 Clip the front of the thermostat back onto the thermostat back plate. WiFi Series Model: DT-ETS WiFi RF... -
Page 5: Lcd Display
Setup/Programming Keys - Used to navigate setup options. Up/Down Keys - Increase or decrease values shown on bottom digit group. Current Temp - Indicates the current sensor temperature. Units of Temperature - Degrees Celsius or Fahrenheit. WiFi Series Model: DT-ETS WiFi RF... - Page 6 IP address of the Multi-Link. Log into your wireless router and navigate to the LAN settings page. WiFi Series Model: DT-ETS WiFi RF...
-
Page 7: Security Types And Compatibility
You will not be able to connect to your thermostat without changing this setting on These restrictions are common to most routers but you should refer to the router G model routers. manual for specific restrictions that apply to your model. WiFi Series Model: DT-ETS WiFi RF... -
Page 8: Remote Access Via App
These are both set to “admin” as default. We recommend you change these settings to ensure the security of your system. For further information, click the help link within the browser. WiFi Series Model: DT-ETS WiFi RF... -
Page 9: Pairing With The Rc2-W
(You must set a unique receiver address for each receiver installed). • Press DONE to confirm and exit ..................• To pair the thermostat with the receiver, press and hold the SCREEN button for 10 seconds ..................Comms LED WiFi Series Model: DT-ETS WiFi RF... -
Page 10: Clean Screen
To activate the lock press the bottom right corner of the display and hold for 10s. • When activated, you will see the Keypad Lock symbol. • To cancel, press the bottom right corner of the display again for 10 secs. Keypad Lock Indicator Set Temperature Set Icon WiFi Series Model: DT-ETS WiFi RF... -
Page 11: Frost Protection
To cancel the frost protect mode, press the key once. To turn the thermostat back ON, press the ON key once ..........Thermostat completely OFF Thermostat powered ON Frost Protection Mode Enabled *See Feature 3 on page 21 WiFi Series Model: DT-ETS WiFi RF... -
Page 12: Optional Features Explained
This can be set from 00 - 15 minutes. The default is 00 which means there is no delay. Feature 06 – Not used on this model. WiFi Series Model: DT-ETS WiFi RF... -
Page 13: Adjusting The Optional Settings
00 - 10 • Press DONE to confirm settings and exit ............Sensor Selection 00 = Built in sensor, 01 = Remote air sensor - 45 C (28 C = Default) Floor Temperature Limit WiFi Series Model: DT-ETS WiFi RF... -
Page 14: Re-Calibrating The Thermostat
Press the ON key once to turn the thermostat back on ..........• Press the ON key once to turn the thermostat display back on ......All icons displayed simultaneously. Factory reset is complete. Calibration Temperature Setting Set Icon WiFi Series Model: DT-ETS WiFi RF... -
Page 15: Error Codes
Mains Supply or the probe is faulty. From Fused Spur Live Error Icon Neutral N.B. The DT-ETS WiFi RF is designed to work with the RC2-W. Please refer to the appropriate Error Number diagram for connections to your Room heating system. -
Page 16: Notes
Wiring Diagram - DT-ETS WiFi RF Notes RC2-W Receiver Connections ..................................Floor Probe Matting (Fit in tubing) ..................................Mains Supply ..................................230V - 16 Amps ..................................Live ..................................Neutral ....................................................................LOAD ..................................Floor ..................................Sensor 230VAC ..................................RC2-W .................................. - Page 17 Heating Professionals: Request a copy of our product installation guide containing detailed technical specifications for our complete product range: www.heatmiser.com/guide Want More Information? Call our support team on: +44 (0)1254 669090 Or view technical specifications directly on our website: www.heatmiser.com Twitter: heatmiseruk Facebook: facebook.com/thermostats...