1. Manuals
  2. Brands
  3. AIRLESSCO Manuals
  4. Paint Sprayer
  5. TS650
  6. Operation

AIRLESSCO TS650 Operation

Interior texture sprayer
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Operation
Interior Texture Sprayer TS650
For use with water based materials only. For professional use only.
Not approved to European explosive atmosphere requirements.
24F565
50 psi (.35 MPa, 3.5 bar) Maximum Fluid Working Pressure
100 psi (.7 MPa, 7 bar) Maximum Air Input Pressure
Important Safety Instructions
Read all warnings and instructions in this
manual. Save these instructions.
Related Manuals
311969
3A1176
3A1174B
EN
ti8370a

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the TS650 and is the answer not in the manual?

Questions and answers

Related Manuals for AIRLESSCO TS650

Summary of Contents for AIRLESSCO TS650

  • Page 1 Operation 3A1174B Interior Texture Sprayer TS650 For use with water based materials only. For professional use only. Not approved to European explosive atmosphere requirements. 24F565 50 psi (.35 MPa, 3.5 bar) Maximum Fluid Working Pressure 100 psi (.7 MPa, 7 bar) Maximum Air Input Pressure...
  • Page 2 Warnings Warnings The following warnings are for the setup, use, grounding, maintenance, and repair of this equipment. The exclama- tion point symbol alerts you to a general warning and the hazard symbols refer to procedure-specific risks. When these symbols appear in the body of this manual, refer back to these Warnings. Product-specific hazard symbols and warnings not covered in this section may appear throughout the body of this manual where applicable.

  • Page 3: Fire And Explosion Hazard

    Warnings WARNING WARNING WARNING WARNING FIRE AND EXPLOSION HAZARD Flammable fumes, such as solvent, in work area can ignite or explode. To help prevent fire and explosion: • Use equipment in well ventilated area. • Sprayer generates sparks. When flammable liquids are used near the sprayer or for flushing or cleaning, keep sprayer at least 20 feet (6 meters) away from explosive vapors.

  • Page 4: Personal Protective Equipment

    • Do not kink or over-bend the hose. • Do not expose the hose to temperatures or to pressures in excess of those specified by Airlessco. • Do not use the hose as a strength member to pull or lift the equipment.
  • Page 5 Warnings NOTICE Water or material remaining in unit when temperatures are below freezing can damage motor and/or delay pump startup. To insure water and material are completely drained out of unit: 1. Remove material line from sprayer. 2. Tip sprayer up as shown. ti9075a Before adding material or starting unit in cold weather, run warm water through pump.

  • Page 6: Component Identification

    Component Identification Component Identification ti8369a 3.5 cfm@40 min. Item Component Item Component Pump Hose Outlet Burp Guard RotoFlex™ II Pump (inside) ON/OFF Switch Texture Spray Gun (Manual 311969) Power Cord (120V, 15 ft) Nozzle (2 included, see Nozzle Selection, page 11) Material Hopper - 5 gallon Material Hose (20 ft) Cord Wrap...

  • Page 7: Pressure Relief Procedure

    Preparation Preparation Pressure Relief Procedure Check with a qualified electrician or serviceman if grounding instructions are not completely understood, or if in doubt as to whether the product is properly grounded. Do not modify plug provided; if it will not fit the outlet, have proper outlet installed by a qualified To reduce risk of injury, follow this procedure whenever electrician.

  • Page 8: Texture Spraying

    Setup Setup 5. Install spray nozzle. See Recommended Nozzle Selection Chart, page 11. Texture Spraying 1. Connect air hose to user-supplied air compressor & material hose (G) to material hose outlets. ti9774a NOTE: To break in new pump run dry for no more than 2 minutes.
  • Page 9 Setup 10. Add pre-mixed texture mix to material hopper. See 13. To achieve uniform spray pattern, adjust air valve Mixing Material, page 10. and flow adjustment nut on gun. If you can not achieve a desired pattern, change nozzle, page 11. 11.

  • Page 10: Mixing Material

    Mixing Material Mixing Material NOTICE Correct material mixture is essential. The pump will not operate if the mixture is too thick. NOTE: For an accurate test, be sure gauge is com- NOTE: Mix the material in a separate container before pletely dry and clean every time it is used.

  • Page 11: Spray Techniques

    Spray Techniques Spray Techniques Recommended Nozzle Selection Chart To Get Less Material Try one or a combination of these methods: Application Nozzle Size Air Volume • Open air valve. Simulated 6 mm, white medium to (fine to medium) Acoustic 8 mm, gray high (coarse) •...

  • Page 12: Shut Down And Clean-Up

    Shutdown and Cleanup Shutdown and Cleanup 5. Spray inside material hopper to circulate water NOTICE through gun and hose. While circulating water, use • Keep pump and hose clean when switching gun to clean material hopper. between simulated acoustic, knockdown and orange peel applications.

  • Page 13: Troubleshooting

    Refer to Grounding and Electrical Requirements, page 7. Gun needle plugged Clean needle and retry. Worn compressor Replace compressor. Contact an authorized Airlessco Service Center. Lines not connected Check all quick disconnect connec- tions to gun and hoses. Damaged hose Replace hose.
  • Page 14 Troubleshooting Problem Cause Solution Speed of application slow or slower New pump hose not broken in Run pump dry for no more than 2 properly minutes. Material too thick Thin material. Nozzle too small Change nozzles to a larger size. See Recommended Nozzle Selection Chart, page 11.

  • Page 15: Technical Data

    0.65 gpm TS650 Dimensions and Weight Length........

  • Page 16: Airlessco Standard Warranty

    With the exception of any special, extended, or limited warranty published by Airlessco, Airlessco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by Airlessco to be defective.

This manual is also suitable for:

24f565

Table of Contents