Page 2
Congratulations on your latest Target purchase. Now what? Don’t start sweating over this box of parts. This will be easy. We did the hard work for you. All you need to do is follow our simple instructions and you’ll be on your way to transforming your room in no time.
Page 3
table of contents introduction hardware parts list how to use the cam lock system assembly 7-15 QUESTIONS? Just call 1-855-MYTGTHOME (855-698-4846) for parts and service. For faster service, have the style number and DPCI number ready when calling.
Page 4
hardware (H1) x 18 (H2) x 15 (H3) x 15 (H4) x 4 (H5) x 21 5/8’’ pan-head screw wooden dowel cam bolt 1’’ flat-head screw (H6) x 4 (H9) x 2 (H7) x 1 (H8) x 1 (H10) x 1 shelf support 5/8”...
Page 5
ITEM DESCRIPTION QUANTITY top panel left side panel right side panel adjustable shelf bottom panel back panel decorative molding top front rail bottom front rail adjustable shelf rail...
Page 7
step 1. (H1) x 3 (H2) x 2 (H3) x 2 wooden dowel cam bolt 1. Carefully tap small wooden dowels into place. Leave 1/2’’ of the dowels sticking out. 2. Screw-In cam bolts must be screwed down flush with wood panel. 3.
Page 8
step 2. (H1) x 3 (H2) x 2 (H3) x 2 wooden dowel cam bolt 1. Carefully tap small wooden dowels into place. Leave 1/2’’ of the dowels sticking out. 2. Screw-In cam bolts must be screwed down flush with wood panel. 3.
Page 9
step 3. (H1) x 4 (H2) x 3 (H3) x 3 wooden dowel cam bolt 1. Carefully tap small wooden dowels into place. Leave 1/2’’ of the dowels sticking out. 2. Screw-In cam bolts must be screwed down flush with wood panel. 3.
Page 10
step 4. (H1) x 4 (H2) x 3 (H3) x 3 wooden dowel cam bolt 1. Carefully tap small wooden dowels into place. Leave 1/2’’ of the dowels sticking out. 2. Screw-In cam bolts must be screwed down flush with wood panel. 3.
Page 11
step 5. (H4) x 4 1’’ flat-head screw 1. Do not over tighten screws.
Page 12
step 6. (H1) x 4 (H2) x 5 (H3) x 5 wooden dowel cam bolt 1. Carefully tap small wooden dowels into place. Leave 1/2’’ of the dowels sticking out. 2. Screw-In cam bolts must be screwed down flush with wood panel. 3.
Page 13
step 7. pre-drilled holes Begin by installing all of the screws along one hole for anti-tip strap edge of the back panel. Next, using a square or tape measure, make sure that the cabinet is square. (If using a tape measure, the distance from one corner, diagonally to the other corner should be the same in both directions.) Install the remaining screws, starting with the corners.
Page 14
step 8. (H6) x 4 shelf support 1. Insert shelf support into desired hole. Different holes accommodate different shelf heights 2. Angle shelf to fit between the rails and set on top of shelf supports.
Page 15
step 9. (H10) (H8) Position against wall (H9) Mark position of strap hole on wall from s or furn fata N IN - Insta - Plac ll tip-o itur e tip- l cru shin e heav inju - Plac back y item restr aint...
Page 16
WARNING Serious or fatal crushing injuries can occur from furniture tip-over. To help prevent tip- over: - Install tip-over restraint provided. - Place heavy items on lower shelves and as far back as possible. 65 lbs. - Place heaviest items in the lowest drawers. - Unless specifically designed to accommodate, per shelf do not set TVs or other heavy objects on top of...