Page 2
Congratulations on your latest Target purchase. Now what? Don’t start sweating over this box of parts. This will be easy. We did the hard work for you. All you need to do is follow our simple instructions and you’ll be on your way to transforming your room in no time.
Page 3
Table of Contents Introduction Hardware Parts list How to use the cam lock system Assembly 7-15 QUESTIONS? Just call 1-855-MYTGTHOME (855-698-4846) for parts and service. For faster service, have the style number and DPCI number ready when calling.
Page 4
hardware (H1) x 17 (H2) x 8 (H3) x 1 (H4) x 17 (H5) x 21 shelf support wall anchor cam bolt wooden dowel (H7) x 4 (H9) x 1 (H10) x 1 (H6) x 23 (H8) x 1 1” flat-head screw 1-1/2”...
Page 5
ITEM DESCRIPTION QUANTITY Top panel Left end panel Right end panel Adjustable shelves Bottom shelf Back panel Decorative molding Top front stretcher Bottom front stretcher Adjustable shelf stretchers...
Page 7
step 1. (H1) x 4 (H5) x 6 (H4) x 4 cam bolt wooden dowel 1. Carefully tap small wooden dowels into place. Leave 1/2” of the dowels sticking out. 2. Screw-In cam bolts must be screwed down flush with wood panel. 3.
Page 8
step 2. (H1) x 2 (H5) x 3 (H4) x 2 wooden dowel cam bolt 1. Carefully tap small wooden dowels into place. Leave 1/2” of the dowels sticking out. 2. Screw-In cam bolts must be screwed down flush with wood panel. 3.
Page 9
step 3. (H1) x 3 (H5) x 4 (H4) x 3 cam bolt wooden dowel 1. Carefully tap small wooden dowels into place. Leave 1/2” of the dowels sticking out. 2. Screw-In cam bolts must be screwed down flush with wood panel. 3.
Page 10
step 4. (H4) x 3 (H1) x 3 (H5) x 4 cam bolt wooden dowel 1. Carefully tap small wooden dowels into place. Leave 1/2” of the dowels sticking out. 2. Screw-In cam bolts must be screwed down flush with wood panel. 3.
Page 11
step 5. (H7) x 4 1” flat-head screw 1. Do not over tighten screws.
Page 12
step 6. (H1) x 5 (H5) x 4 (H4) x 5 cam bolt wooden dowel 1. Carefully tap small wooden dowels into place. Leave 1/2” of the dowels sticking out. 2. Screw-In cam bolts must be screwed down flush with wood panel. 3.
Page 13
step 7. pre-drilled holes screw hole for tip kit Begin by installing all of the screws along one edge of the back panel. Next, using a square or tape measure, make sure that the cabinet is pre-drilled square. (If using a tape measure, the distance holes from one corner, diagonally to the other corner should be the same in both directions.) Install...
Page 14
step 8. (H2) x 8 shelf support 1. Insert shelf supports into desired hole. Different holes accommodate different shelf heights. 2. Slide middle shelves in.
Page 15
step 9. (H11) (H8) (H3) Position against wall a. Position against wall Seri from - Insta furn fata iture l crus - Place ll tip-ov tip-o hing back - Place heav y items restra ver. inju ries - Unle heav poss provi help...
Page 16
WARNING Serious or fatal crushing injuries can occur from furniture tip-over. To help prevent tip- over: - Install tip-over restraint provided. - Place heavy items on lower shelves and as far back as possible. - Place heaviest items in the lowest drawers. - Unless specifically designed to accommodate, do not set TVs or other heavy objects on top of 65 lbs.