Congratulations on your latest Target purchase. Now what? Don’t start sweating over this box of parts. This will be easy. We did the hard work for you. All you need to do is follow our simple instructions and you’ll be on your way to transforming your room in no time.
Page 3
table of contents Introduction Hardware Parts list Assembly 6-12 Care and maintenance and warranty Important safety information Questions? Just call 1-855-MYTGTHOME (855-698-4846) for parts and service. For faster service, have the style number and article number ready when calling.
Page 4
hardware (H1) x 16 (H2) x 4 (H4) x 1 (H3) x 4 1/4” x 13 mm bolt M4 x 30 mm screw bumper hex wrench Spare hardware...
ITEM DESCRIPTION QUANTITY Top glass Side frame Top stretcher Bottom stretcher Drawer box support Drawer box...
Page 6
step 1. NOTE: DO NOT fully tighten all bolts until you finish assembling all parts. Once assembled, go back and fully tighten all bolts. This will make the assembly easier. (H4) x 1 (H1) x 2 Hex wrench 1/4” x 13 mm bolt Align and attach the two top stretchers (C) to the top of one side frame (B).
Page 7
step 2. NOTE: DO NOT fully tighten all bolts until you finish assembling all parts. Once assembled, go back and fully tighten all bolts. This will make the assembly easier. (H4) x 1 (H1) x 4 Hex wrench 1/4” x 13 mm bolt Fasten the two drawer box supports (E) to the middle rail of side frame (B).
Page 8
step 3. The drawer front faces up NOTE: DO NOT fully tighten all bolts until you finish assembling all parts. Once assembled, go back and fully tighten all bolts. This will make the assembly easier. (H4) x 1 (H1) x 2 Hex wrench 1/4”...
Page 9
step 4. NOTE: DO NOT fully tighten all bolts until you finish assembling all parts. Once assembled, go back and fully tighten all bolts. This will make the assembly easier. (H4) x 1 (H1) x 8 Hex wrench 1/4” x 13 mm bolt Repeat the same procedure to attach the other side frame (B) at opposite end.
Page 10
step 5. (H2) x 4 M4 x 30 mm screw Firmly press the drawer box (F) against the drawer box supports (E). Make sure that the mounting holes overlap the pilot holes underneath the drawer box (F) properly. Fasten the drawer box (F) to the drawer box supports (E).
Page 11
step 6. The four corners are the most weak portion of the glass. DO NOT bump any corner against the metal tubes when installing the glass shelf, which may cause possible injury. (H3) x 4 bumper Stand the unit upright and firmly put the bumpers into the available holes on both top stretchers (C). Gently place the top glass (A) onto the bumpers on the top stretchers (C).
Page 12
step 7. Floor leveler Position the unit at the desired location. If necessary, adjust the floor levelers to level the unit.
Care and Maintenance • Use a soft, clean cloth that will not scratch the surface when dusting. • Use of furniture polish is not necessary. Should you choose to use polish, test first in an inconspicuous area. • Using solvents of any kind on your furniture may damage the finish. •...
Page 14
The maximum recommended weight allowance is 22.7 kg / 50 lb for glass top and open storage shelf. The maximum recommended weight allowance is 9.1 kg / 20 lb for drawer. Death or serious injury may occur when children climb on audio and/or video equipment furniture. A remote control or toys placed on the furnishing may encourage a child to climb on the furnishing and as a result may tip over onto the child.
Page 15
Questions? Just call 1-855-MYTGTHOME (855-698-4846) for parts and service. For faster service, have the style number and article number ready when calling.
Need help?
Do you have a question about the Project 62 T80526-4 and is the answer not in the manual?
Questions and answers