Related Manuals for Body Champ TRIO-TRAINER BRT1875
Summary of Contents for Body Champ TRIO-TRAINER BRT1875
- Page 1 BRT1875 BRT2885 U.S. Patent number US9474925B1 This product is intended for indoor, home use only and is not to be used in a commercial setting. OWNER’S MANUAL...
- Page 2 This Page Intentionally Left Blank...
- Page 3 PLEASE KEEP THESE INSTRUCTIONS FOR FUTURE USE & REFERENCE. DO NOT DISCARD. WARNING: SERIOUS INJURIES AND EVEN DEATH CAN OCCUR IF THE PROPER SAFETY PRECAUTIONS ARE NOT FOLLOWED. The diagram below highlights and reviews many of the important Safety and Warning labels also found on the unit. Please ensure any user of the unit familiarizes themselves with this Safety and Warning guidelines before use.
-
Page 4: General Information
General Information Safety Storage and Use Before you undertake any exercise program, please be sure to Your product is intended for use in clean dry conditions. You consult with your doctor. should avoid storage in excessively cold or damp places as Frequent strenuous exercise should be approved by your this may lead to corrosion and other related problems. -
Page 5: Before Assembly
Before Assembly WARNING 1. Take a few minutes to familiarize yourself with the parts and hardware included with your product. 2. The assembly may require two people. 3. Check the frame for any damage and check any wiring (if present) for rips or tears. If you detect damage, rips, or tears, please contact our Customer Support Team before beginning any assembly. -
Page 6: Part Listing
Part Listing The following parts list describes all of the parts illustrated in the exploded diagram on the following page. PLEASE NOTE: most of these parts are already pre-assembled on your unit. # Description # Description 01 Main Frame 43 Cap Nut (M8) 02 Center Post 44 Bushing 03 Left Pedal Tube... -
Page 7: Exploded View
Exploded View The following diagram is provided to help you familiarize yourself with the parts and hardware that will be used during the assembly process. PLEASE NOTE : : Not all of the parts and hardware you see here will be used while you are assembling the machine because some of these items are already pre-installed. -
Page 8: Hardware And Tool List
Hardware and Tool List The following hardware is used to assemble your unit. Please take a moment to familiarize yourself with these items. PLEASE NOTE: Most of these parts are already pre-assembled on your unit. Do not be alarmed if you see parts on this page that are not included in your hardware packet. -
Page 9: Assembly Step
Assembly STEP 1 Hardware Required NOTE BEFORE STARTING THE ASSEMBLY PROCESS : To avoid misalignment due to over-tightening, please do not use a wrench and use only hand-tightening for now to ensure easy assembly. Wrench-tightening should be performed after all parts are assembled to ensure all nuts, bolts, and parts are tightly secured before use. - Page 10 Assembly STEP 2 Connect the Main Sensor Wire (Lower)(#72) to the Main Hardware Required Sensor Wire (Upper) (#71). Then connect the Tension Controller Cable (#81) to the cable of Tension Controller (#78). #25 Bolt (M8x15mm) [6 pieces] Remove the Bolts (#25), Spring Washers (#38) and Big Washers (#80) that are pre-assembled on the Main Frame (#01) and set them aside as they will be used later in #80 Big Washer (M8)
- Page 11 Assembly STEP 3 Referring to the drawing below, insert the Axle (#19) through the Hardware Required horizontal stems on the Center Post (#02). Then, on the left side of the Axle (#19) -- in the following order, slide on: one Wavy Washer (#36) followed by the Left Coupler Bar (#05), one D Shape Washer (#37), one Round Cap (#57), one Washer (#33), and secure using one Bolt (#26).
- Page 12 Assembly STEP 4 Attach the Left/Right Pedals (#45/#46) onto the Left/Right Hardware Required Pedal Tubes (#03/#04) as shown in the drawing below using a total of six Hex Bolts (#21), six Washers (#33), and six Nylon Nuts (#40). #21 Hex Bolt (M8x40mm) On the left side, attach the Left Foot Pedal (#73) to the front of [6 pieces] Left Pedal Tube (#03) using one Hex Bolt (#24) through one...
- Page 13 Assembly STEP 5 Please remove the two Knob Bolts (#54) that are pre-assembled Hardware Required on the Left/Right Coupler Bars (#05/#06). On the left side, insert Left Handle Bar (#15) into the opening at the tip of Left Coupler Bar (#05). Align the holes of the Left Handle Bar (#15) and Left Coupler Bar (#05) and secure by using one Knob Bolt (#54) through.
- Page 14 Assembly STEP 6 A. PULSE HANDLEBAR Hardware Required Install the Pulse Handle Bar (#13) on the rear side of the Center Post (#02) as shown in the illustration below using two Bolts (#29). Please ensure the wire of the Handle Pulse (#70) is free and clear, avoiding pinching it during this assembly step.
- Page 15 Assembly STEP 7 Start with loosening the pre-assembled Spring Loaded Knob (#53) Hardware Required and pull back slightly on it so that you may proceed to insert the Seat Post (#08) into the opening of the post that is protruding from the Main Frame (#01) down a minimum of four inches so that the corresponding holes can engage.
- Page 16 Assembly STEP 8 Attach the Seat Cushion (#64) to the horizontal bar of the Hardware Required Seat Cushion Frame (#09) and secure from the bottom using four Bolts (#25). Then, attach the Backrest Cushion (#65) to the Backrest Cushion Frame (#10) and secure using two Bolts (#27) through two Washers (#33).
-
Page 17: Computer Operation
Computer Operation Key Function MODE : Press this button to select the display function of your choice. RESET : Hold MODE button for 3 seconds to reset all value to zero. UP DOWN : Press UP DOWN to set workout level Operation Procedures FUNCTIONS SCAN... - Page 18 Computer Operation How To Install and Replace Batteries 1. Open the battery door on the back of the computer. 2. The computer operates on two AAA batteries (included). Refer to the illustration to install or replace the batteries. NOTE : 1.
-
Page 19: Safety And Maintenance
Safety and Maintenance Safety & Warning • Make sure all nuts, bolts, and screws are tightened prior to use. • Be sure that all adjustment locking devices and safety devices are properly engaged prior to use! • Never over-tighten the above-mentioned devices and parts to avoid damage to the unit. •... -
Page 20: Troubleshooting
Troubleshooting (AFTER COMPLETE ASSEMBLY) Troubleshoot Area Solution Calories/Distance/ If the computer is not displaying the CALORIES/DISTANCE/TIME/(ETC.) functions (or you are getting inaccurate readings), please adjust Time (Etc.) the following: 1. Check to ensure all computer sensor wires are properly connected and are not damaged. 2. - Page 21 Warm-Up Instructions Before use, you must read and understand all instructions & warnings stated in this Owner’s Manual as well as posted on the equipment. Before beginning any exercise program including the following flexibility exercises, please consult with your physician. The following flexibility exercises are provided to you as a means to prevent injury while you are exercising.
- Page 22 Warm-Up Instructions Shoulder Stretch Quadriceps Stretch Calf Twister 1. Bring your right hand over your 1. Stand on your left leg and hold 1. Place both hands against a wall right shoulder to the onto a support with your left to aid your balance.
- Page 23 This Page Intentionally Left Blank...
- Page 24 THANK YOU FOR YOUR PURCHASE MODEL NO.: BRT1875 BRT2885 Please fill in the information below and keep this manual along with your sales receipt as proof of purchase. Serial Number : Date of Purchase : Retailer : Body Flex Sports, Inc. 21717 Ferrero Parkway Walnut, CA 91789 Phone : 1 (888) 266-6789...