Related Manuals for Beckhoff CU8802-0000
Summary of Contents for Beckhoff CU8802-0000
- Page 1 Installation- and Operating instructions for CU8802-0000 CP-Link 4 transmitter box – The Two Cable Display Link Version: 1.2 Date: 2020-02-20...
-
Page 3: Table Of Contents
DVI Input (X20) 3.2.4 CP-Link 4 Output (X30) 3.2.5 Retainer brackets LED-Diagnostics 4 Installation Transport and Unpacking 4.1.1 Transport 4.1.2 Unpacking Mounting/ Demounting Connecting devices 4.3.1 Connecting cables 4.3.2 Connecting Power Supply 5 Operation CP-Link 4 Architecture Description Maintenance 5.2.1 Cleaning CU8802-0000... - Page 4 Dimensions of basic device Dimensions of basic device with strain relief 7 Technical Data 8 Appendix Beckhoff Support and Service 8.1.1 Beckhoff branches and partner companies 8.1.2 Beckhoff company headquarters Approvals for USA and Canada FCC Approval for USA FCC Approval for Canada...
-
Page 5: Foreword
Modifications to hardware or software configurations other than those described in the documentation are not permitted, and nullify the liability of Beckhoff Automation GmbH & Co. KG. 1.1.6 Delivery conditions In addition, the general delivery conditions of the company Beckhoff Automation GmbH & Co. KG apply. CU8802-0000... -
Page 6: Description Of Safety Symbols
• the operation manual is in good condition and complete, and always available for reference at the location of the product • none of the safety and warning notes attached to product are removed, and that all notes remain legible. CU8802-0000... -
Page 7: For Your Safety
Beckhoff Automation GmbH & Co. KG. In addition, the following actions are excluded from the liability of Beckhoff Automation GmbH & Co. KG: • Failure to comply with this documentation. -
Page 8: Marking
For your safety • The equipment shall only be used in an area of not more than pollution degree 2, as defined in IEC 60664-1. 2.1.3 Marking The CU8802-0000 bears a continuous serial number and markings on the nameplate: CU8802-0000... -
Page 9: Product Description
• Power supply for the Control Panel with connection of 24 V at the Control Panel • Metal housing for DIN rail installation • CP-Link 4 transfers USB 2.0 with 100 Mbit/s and DVI • 24 V input for power supply of the CU8802 transmitter box • Protection class IP20. CU8802-0000... -
Page 10: Connections
Note function of the touchscreen. 3.2.2 USB Input (X10) Connector USB TYP-B LP-mount. WS The CP-Link 4 transmitter box CU8802-0000 is connected with the Industrial PC via the USB input (X10). The maximum cable length is 1 m. Signal Signal... -
Page 11: Dvi Input (X20)
Product Description 3.2.3 DVI Input (X20) Connector DVI-D 3x8pole Digital LP-mount. The CP-Link 4 transmitter box CU8802-0000 is connected with the Industrial PC via the DVI input (X20). The maximum cable length is 1 m. Signal Signal TMDS Data 2- n.c. -
Page 12: Retainer Brackets
1. Put the strain relief at an angle in front of the side wall of the device so that the labelled side can be seen. 2. Hook the strain relief via the left side of the mount into the mounting rail. CU8802-0000... - Page 13 2. Fix the USB plug with cable straps to the retainer bracket. 3. Check the tensile strength of the wire. If necessary, retighten the cable straps. 4. Cut off the remains of the cable straps with nippers or a side cutter. CU8802-0000...
-
Page 14: Led-Diagnostics
3.3 LED-Diagnostics Allocation State Meaning Power supply no power supply lights green 24 V connected no connection Connection to the Control Panel lights green connection to the Control Panel established Activity no image data transmission flashes yellow DVI data transmission CU8802-0000... -
Page 15: Installation
4. Please keep the associated paperwork. It contains important information for handling the unit 5. Check the contents for visible shipping damage. If you notice any shipping damage or inconsistencies between the contents and your order, you should notify Beckhoff Service. CU8802-0000... -
Page 16: Mounting/ Demounting
Installation 4.2 Mounting/ Demounting The CP-Link 4 transmitter box CU8802-0000 can be snapped onto a 35 mm mounting rail conforms to EN 50022: To release the CP-Link 4 transmitter box CU8802-0000 from the mounting rail, press the device downwards till you can remove it from the rail. -
Page 17: Connecting Devices
• Switch off all the devices that are to be connected • Disconnect all the devices that are to be connected from the power supply • Connect all the cables between the CU8802-0000 and the devices that are to be connected • Reconnect all devices to the power supply. -
Page 18: Operation
The device can be cleaned with a soft, damp cloth. Do not use any aggressive cleaning materials, thinners, scouring material or hard objects that could cause scratches. 5.2.2 Maintenance The CU8802-0000 CP-Link 4 transmitter box is maintenance-free. 5.3 Shutting down 5.3.1 Disposal Observe national electronics scrap regulations Observe the national electronics scrap regulations when disposing of the device. -
Page 19: Dimensions
The product is characterized by small overall installed size. With a height of 100 mm, the module dimensions exactly match those of the Beckhoff Bus Terminals. Together with the lowered connector surfaces, this means that it can be used in a standard terminal box with a height of 120 mm... -
Page 20: Dimensions Of Basic Device With Strain Relief
Dimensions 6.2 Dimensions of basic device with strain relief All dimensions are given in mm. CU8802-0000... -
Page 21: Technical Data
Technical Data 7 Technical Data Product name CU8802-0000 Inputs 1 USB input with USB B socket to be connected to the PC 1 DVI input with DVI-D socket to be connected to the PC Output 1 CP-Link 4 output with RJ45 socket for Cat.6... -
Page 22: Appendix
Please contact your Beckhoff branch office or partner company for local support and service on Beckhoff products! The contact addresses for your country can be found in the list of Beckhoff branches and partner companies: www.beckhoff.com. You will also find further documentation for Beckhoff components there. -
Page 23: Approvals For Usa And Canada
Technical modifications to the device may cause the loss of the FCC approval. Note 8.4 FCC Approval for Canada FCC: Canadian Notice This equipment does not exceed the Class A limits for radiated emissions as described in the Radio Interference Regulations of the Canadian Department of Communications. CU8802-0000...