Related Manuals for SMA SUNNY CENTRAL CP XT Series
Summary of Contents for SMA SUNNY CENTRAL CP XT Series
- Page 1 Installation Manual Retrofitting of the Option "Noise Reduction" SUNNY CENTRAL of the CP XT Series and SUNNY CENTRAL STORAGE ENGLISH SCCPXT-SCS_NR-IA-en-12 | 98-129600.02 | Version 1.2...
- Page 2 The information contained in these documents is the property of SMA Solar Technology AG. Any publication, whether in whole or in part, requires prior written approval by SMA Solar Technology AG. Internal reproduction used solely for the purpose of product evaluation or other proper use is allowed and does not require prior approval.
-
Page 3: Table Of Contents
SMA Solar Technology AG Table of Contents Table of Contents Information on this Document..................... Validity ................................Target Group ..............................Levels of warning messages..........................Symbols in the Document..........................Safety ............................Intended Use..............................Safety Information ............................Personal Protective Equipment ........................Product Overview ........................10 Design of the Inverter ............................ -
Page 4: Information On This Document
1 Information on this Document SMA Solar Technology AG 1 Information on this Document Validity This document is a supplement to the provided installation manual of the product and describes the mounting of the accessory parts of the order option "Noise Reduction". -
Page 5: Symbols In The Document
SMA Solar Technology AG 1 Information on this Document WARNING Indicates a hazardous situation which, if not avoided, could result in death or serious injury. CAUTION Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury. -
Page 6: Safety
2 Safety SMA Solar Technology AG 2 Safety Intended Use The assembly of the accessory parts of the order option "Noise Reduction" reduces the noise emission of the product and is suitable for Sunny Central inverters of the CP XT series and Sunny Central Storage battery inverters. -
Page 7: Safety Information
SMA Solar Technology AG 2 Safety Safety Information This section contains safety information that must be observed at all times when working on or with the product. To prevent personal injury and property damage and to ensure long-term operation of the product, read this section carefully and observe all safety information at all times. - Page 8 2 Safety SMA Solar Technology AG WARNING Danger to life from electric shock when entering the PV field Ground-fault monitoring does not provide protection from personal injury. PV modules which are grounded with ground-fault monitoring discharge voltage to ground. Entering the PV field can result in lethal electric shocks.
-
Page 9: Personal Protective Equipment
SMA Solar Technology AG 2 Safety NOTICE Property damage due to dust intrusion and moisture penetration Dust or moisture intrusion can damage the product and impair its functionality. • Do not open the enclosure during rainfall or when humidity exceeds the specified thresholds. The humidity thresholds are: 15% to 95%. -
Page 10: Product Overview
3 Product Overview SMA Solar Technology AG 3 Product Overview Design of the Inverter Figure 1: Design of the Inverter Position Designation Inverter cabinet Interface cabinet Connection area Type Label The type label clearly identifies the product. One type label is present in the inverter. The type label is located in the right-hand top corner inside the interface cabinet. -
Page 11: Scope Of Delivery
SMA Solar Technology AG 4 Scope of Delivery 4 Scope of Delivery Check the scope of delivery for completeness and any apparent external damage. Contact your distributor if the scope of delivery is incomplete or damaged. Scope of delivery of the silencing baffle... - Page 12 4 Scope of Delivery SMA Solar Technology AG Scope of delivery of the kick plate set and rear panel Figure 3: Scope of delivery Position Quantity Designation Inverter rear panel Kick plate set Ventilation plate Assembly paste (Anti-Seize) Countersunk screw...
-
Page 13: Preparation For Mounting
SMA Solar Technology AG 5 Preparation for Mounting 5 Preparation for Mounting Provide storage facilities prior to the start of assembly work Storage facilities for the enclosure parts must be provided prior to the start of the assembly work. Make sure that the enclosure parts, seals and screws are not damaged during storage. -
Page 14: Mounting
6 Mounting SMA Solar Technology AG 6 Mounting Safety during Mounting NOTICE Property damage due to dust intrusion and moisture penetration During assembly work, the inverter is not sufficiently protected against moisture and dust. If the assembly work is carried out during rainfall or in a dusty environment, moisture or dust can penetrate the inverter. Dust or moisture intrusion can damage the product and impair its functionality. -
Page 15: Removing The Existing Ventilation Plate
SMA Solar Technology AG 6 Mounting Requirement: ☐ The additionally required mounting material must be available (see Section 5.1, page 13). Procedure: DANGER Danger to life from electric shock due to live voltage Prior to performing any work on the inverter, disconnect it from voltage sources (see inverter installation manual). -
Page 16: Disassembling The Rear Panel
6 Mounting SMA Solar Technology AG Disassembling the Rear Panel Figure 5: Position of the rear panel to be disassembled Position Designation Rear panel to be disassembled Requirements: ☐ Two persons must be available for disassembling the rear panel. ☐ The required mounting material must be available (see Section 5.1, page 13). - Page 17 SMA Solar Technology AG 6 Mounting 3. Unscrew all ten screws of the rear panel using a suitable screwdriver (TX 30). 4. Remove all screws from the rear panel and retain for later use. 5. Carefully pull the rear panel of the inverter cabinet approx.
-
Page 18: Mounting The New Rear Panel
6 Mounting SMA Solar Technology AG Mounting the New Rear Panel Requirements: ☐ Two persons must be available for disassembling the rear panel. ☐ The required mounting material must be available (see Section 5.1, page 13). ☐ The inverter must be sufficiently protected from inclement weather. -
Page 19: Mounting The Kick Plate For The Sound Absorber
SMA Solar Technology AG 6 Mounting 7. Insert the five upper screws of the rear panel into the threads and tighten (TX 30, torque: 8 Nm). 8. Make sure that the rear panel is correctly mounted. Mounting the Kick Plate for the Sound Absorber The kick plate must be mounted with an additional air duct on the rear side of the inverter. -
Page 20: Mounting The Silencing Baffle
6 Mounting SMA Solar Technology AG Mounting the Silencing Baffle With the order option "Noise reduction", a silencing baffle is delivered with the inverter. The silencing baffle must be mounted on the rear panel of the inverter cabinet. When mounting, use the allround paste from the scope of delivery for the bolted connections. - Page 21 SMA Solar Technology AG 6 Mounting 2. Insert a cylindrical screw with contact washer into the top left thread. Do not tighten the screw yet. 3. Screw five pan head flange screws into the upper threads on the cover. Do not tighten the screws yet.
- Page 22 6 Mounting SMA Solar Technology AG Mounting the Rain Shield Required mounting material: ☐ 2 cylindrical screws ☐ 2 contact washers ☐ 6 pan head flange screws Procedure: 1. Position the rain shield on the silencing baffle. 2. Screw two cylindrical screws with contact washers into the bottom right and left threads on the cover and tighten them (torque: 8 Nm).
-
Page 23: Switching The Inverter On
SMA Solar Technology AG 7 Switching the Inverter On 7 Switching the Inverter On Switching the Inverter On Only switch the inverter on in accordance with the information provided in the inverter documentation. • Prior to switching the inverter on, ensure that all work has been carried out correctly and that there are no mounting objects left in the inverter. -
Page 24: Dimensions And Minimum Clearances
8 Dimensions and minimum clearances SMA Solar Technology AG 8 Dimensions and minimum clearances Dimensions of the Inverter Mounting the silencing baffle changes the dimensions and safety clearances of the inverter. 956 mm 2562 mm 700 mm 1307 mm 1204 mm... - Page 25 SMA Solar Technology AG 8 Dimensions and minimum clearances Minimum clearances for two inverters with mv transformer to be installed outdoors Option 1 Figure 8: Minimum clearance for two inverters with MV transformer Position Designation Inverter 1 Inverter 2 MV transformer and MV switchgear...
- Page 26 8 Dimensions and minimum clearances SMA Solar Technology AG Option 2 300 mm 1200 mm 300 mm Figure 9: Minimum clearance for two inverters with MV transformer Position Designation Inverter 1 Inverter 2 MV transformer and MV switchgear Cable route between inverter and MV switchgear...
-
Page 27: Technical Data
SMA Solar Technology AG 9 Technical Data 9 Technical Data The technical data of the product changes when assembling the silencing baffle. Only the technical data that differ from the standard version is shown here. You will find the complete overview of the product's technical data in the installation manual. -
Page 28: Contact
10 Contact SMA Solar Technology AG 10 Contact If you have technical problems with our products, please contact the SMA Service Line. We require the following information in order to provide you with the necessary assistance: • Device type • Serial number •... - Page 29 SMA Solar Technology AG 10 Contact United Arab SMA Middle East LLC India SMA Solar India Pvt. Ltd. Emirates Abu Dhabi Mumbai +971 2234 6177 +91 22 61713888 SMA Online Service Center: www.SMA-Service.com ไทย SMA Solar (Thailand) Co., Ltd. 대한민국 SMA Technology Korea Co., Ltd.
- Page 30 www.SMA-Solar.com...