h h i i g g h h f f r r e e q q u u e e n n c c y y . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 2 9 9
o o w w n n e e r r r r e e c c o o g g n n i i t t i i o o n n . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 2 9 9
r r a a p p i i d d r r e e s s u u m m e e l l o o g g i i c c . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 3 0 0
p p o o w w e e r r s s a a v v e e r r m m o o d d e e . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 3 0 0
p p r r o o g g r r a a m m m m i i n n g g o o p p t t i i o o n n s s . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 3 1 1
s s e e c c u u r r i i t t y y & & c c o o n n v v e e n n i i e e n n c c e e e e x x p p a a n n s s i i o o n n s s . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 3 4 4
g g l l o o s s s s a a r r y y o o f f t t e e r r m m s s . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 3 6 6
Do you have a question about the Automate AM7 and is the answer not in the manual?
Questions and answers
Tim Lyons
February 1, 2025
Car starts then immediately shuts off
1 comments:
Mr. Anderson
February 10, 2025
The Automate AM7 may start and then immediately shut off if it is programmed for voltage sense and the voltage variation between the engine off and running is too small. This can cause the remote start unit to "think" the vehicle has not started and shut it down. Adjusting the voltage check setting to "LOW" may help in such cases.
This answer is automatically generated
Edward Kemper
February 19, 2025
battery died remote start wont work How do i reprogram the remote to start the car?
1 comments:
Mr. Anderson
February 19, 2025
To reprogram the remote for the Automate AM7 after the battery died, follow these steps:
1. Re-sync the remote: If the remote has been pressed many times out of range or the battery was removed, it may fall out of sync. To re-sync, press the remote button several times within range of the vehicle. The alarm will automatically re-sync and respond to the transmitters normally.
2. If reprogramming is needed: - Open a door (ensure the GREEN wire H1/8 or VIOLET wire H1/6 is connected). - Turn the ignition to the ON position. - Within 10 seconds, press and release the Valet/Program switch the number of times corresponding to the desired channel. - After selecting the channel, press and hold the switch. The LED will flash, and the horn will honk (if connected) to confirm. - Do not release the Program switch until confirmation is complete.
If the learn routine is locked, it must be unlocked using the Bitwriter® before proceeding.
Need help?
Do you have a question about the Automate AM7 and is the answer not in the manual?
Questions and answers
Car starts then immediately shuts off
The Automate AM7 may start and then immediately shut off if it is programmed for voltage sense and the voltage variation between the engine off and running is too small. This can cause the remote start unit to "think" the vehicle has not started and shut it down. Adjusting the voltage check setting to "LOW" may help in such cases.
This answer is automatically generated
battery died remote start wont work How do i reprogram the remote to start the car?
To reprogram the remote for the Automate AM7 after the battery died, follow these steps:
1. Re-sync the remote: If the remote has been pressed many times out of range or the battery was removed, it may fall out of sync. To re-sync, press the remote button several times within range of the vehicle. The alarm will automatically re-sync and respond to the transmitters normally.
2. If reprogramming is needed:
- Open a door (ensure the GREEN wire H1/8 or VIOLET wire H1/6 is connected).
- Turn the ignition to the ON position.
- Within 10 seconds, press and release the Valet/Program switch the number of times corresponding to the desired channel.
- After selecting the channel, press and hold the switch. The LED will flash, and the horn will honk (if connected) to confirm.
- Do not release the Program switch until confirmation is complete.
If the learn routine is locked, it must be unlocked using the Bitwriter® before proceeding.
This answer is automatically generated