Table of Contents
Advertisement
reach from children all remote control transmitters to assure
that the system does not unintentionally remote start the
vehicle. T T H H E E U U S S E E R R M M U U S S T T I I N N S S T T A A L L L L A A C C A A R R B B O O N N
M M O O N N O O X X I I D D E E D D E E T T E E C C T T O O R R I I N N O O R R A A B B O O U U T T T T H H E E
L L I I V V I I N N G G A A R R E E A A A A D D J J A A C C E E N N T T T T O O T T H H E E V V E E H H I I C C L L E E . . A A L L L L
D D O O O O R R S S L L E E A A D D I I N N G G F F R R O O M M A A D D J J A A C C E E N N T T L L I I V V I I N N G G A A R R E E A A S S
T T O O T T H H E E E E N N C C L L O O S S E E D D O O R R P P A A R R T T I I A A L L L L Y Y E E N N C C L L O O S S E E D D
V V E E H H I I C C L L E E S S T T O O R R A A G G E E A A R R E E A A M M U U S S T T A A T T A A L L L L T T I I M M E E S S
R R E E M M A A I I N N C C L L O O S S E E D D . . These precautions are the sole respon-
sibility of the user.
➤
Use of this product in a manner contrary to its intended
mode of operation may result in property damage, personal
injury, or death. (1) Never remotely start the vehicle with the
vehicle in gear, and (2) Never remotely start the vehicle with
the keys in the ignition. The user must also have the neutral
safety feature of the vehicle periodically checked, wherein the
vehicle must not remotely start while the car is in gear. This
testing should be performed by an authorized Directed dealer
in accordance with the Safety Check outlined in the product
installation guide. If the vehicle starts in gear, cease remote
start operation immediately and consult with the authorized
Directed dealer to fix the problem.
➤
After the remote start module has been installed, contact
your authorized dealer to have him or her test the remote
start module by performing the Safety Check outlined in the
product installation guide. If the vehicle starts when
performing the Neutral Safety Shutdown Circuit test, the
10
© 2005 directed electronics—all rights reser ved
Hide quick links:
Advertisement
Table of Contents
Need help?
Do you have a question about the Automate AM7 and is the answer not in the manual?
Questions and answers
Car starts then immediately shuts off
The Automate AM7 may start and then immediately shut off if it is programmed for voltage sense and the voltage variation between the engine off and running is too small. This can cause the remote start unit to "think" the vehicle has not started and shut it down. Adjusting the voltage check setting to "LOW" may help in such cases.
This answer is automatically generated
battery died remote start wont work How do i reprogram the remote to start the car?
To reprogram the remote for the Automate AM7 after the battery died, follow these steps:
1. Re-sync the remote: If the remote has been pressed many times out of range or the battery was removed, it may fall out of sync. To re-sync, press the remote button several times within range of the vehicle. The alarm will automatically re-sync and respond to the transmitters normally.
2. If reprogramming is needed:
- Open a door (ensure the GREEN wire H1/8 or VIOLET wire H1/6 is connected).
- Turn the ignition to the ON position.
- Within 10 seconds, press and release the Valet/Program switch the number of times corresponding to the desired channel.
- After selecting the channel, press and hold the switch. The LED will flash, and the horn will honk (if connected) to confirm.
- Do not release the Program switch until confirmation is complete.
If the learn routine is locked, it must be unlocked using the Bitwriter® before proceeding.
This answer is automatically generated