Related Manuals for Label T-NFC
Summary of Contents for Label T-NFC
- Page 1 T-NFC DIGITAL SELECTOR automatic doors ETERNA and NEXT TRANSLATION OF THE ORIGINAL INSTRUCTIONS T-NFC - En - Rel.1.0 - 01/2019 - CD0749EN...
-
Page 3: Table Of Contents
TABLE OF CONTENTS: DESCRIPTION INSTALLATION DAY-TO-DAY USE OPENING THE DOOR FROM T-NFC INFORMATION AREA DIAGNOSTIC AREA TECHNICAL AREA 1-SET UP 2-FUNCTION 3-SELECTOR OPTION 4-LANGUAGE 5-CONNECTION 6-PASSWORD 7-SERVICE... -
Page 4: Description
DESCRIPTION The T-NFC selector uses the Touch technology for the buttons and features a next-generation, high- contrast display for clearer images. It is used to interface with the door both during “standard” operation (by the user), and during the installation and adjustment of functions and parameters (by the installer). It provides the same adjustment and management functions as the ET-DSEL digital selector;... -
Page 5: Day-To-Day Use
In this case check the connection and retry. DAY-TO-DAY USE The T-NFC model allows to select 6 different program types for day-to-day use: AUTO: The door opens and closes automatically both ways with all sensors activated... -
Page 6: Opening The Door From T-Nfc
Press the A button again to return to the standard opening. The figure below shows an example with the AUTO program. OPENING THE DOOR FROM T-NFC Pressing the B button will issue a door opening command; the closing will be automatic, as for the other sensors. -
Page 7: Information Area
INFORMATION AREA Hold the A button pressed for about 2 seconds to access the information area. The display will sequentially show some information and the list of the door errors that have occurred, if any: SERIAL: Serial code of the automation electronic control unit PARTIAL: Number of operations performed since the latest maintenance. - Page 8 USER PASSWORD MANAGEMENT The T-NFC selector allows to password-protect the operating program change. This function is useful if you wish to prevent unauthorised people from setting the door operating program. To this purpose, you need to enable the user password, by following the procedure described below: Hold the D button pressed for about 2 seconds.
-
Page 9: Technical Area
TECHNICAL AREA As mentioned above, through the T-NFC you can operate the door, adjust its functions and its potentiometers, and manage its maintenance. You can also customise the selector settings. - Page 10 Full setup (FULL): Important! The opening direction is self-learned, provided the leaf is closed when the setup is launched. Remember to close the door before launching the setup. The display shows a list of functions to be selected to operate the door. Press the A button to move to the next function;...
-
Page 11: 2-Function
2-FUNCTION This menu allows to edit the door operating parameters. The automation software supports 80 Functions (On/Off) and 50 digital Potentiometers (0-100%), to adapt the automatism to the requirements of each specific installation. In many cases the default values are enough to ensure an appropriate door movement; should you need to edit any of these parameters or to enable the functions, however, enter this menu. -
Page 12: 3-Selector Option
To exit the technical area and return to the main screen, press SET again. 3-SELECTOR OPTION This menu allows to customise the T-NFC selector. As mentioned in the “DAY-TO-DAY USE” paragraph, it allows to select 6 different operating programs, to enable a reduced opening during winter and to activate a set of special functions through the C button. -
Page 13: 4-Language
The customisable parameter sequence is the following: • AUTO operating program • EXIT operating program • ENTER operating program • OPEN operating program • LOCK operating program • OFF operating program • A function button (winter reduced opening) • C function button (F2 special functions) The last customisable parameter, finally, is: •... -
Page 14: 6-Password
The technical password is stored in the microprocessor controlling the automatic door; as a consequence, it is independent of the selector in use. Once it has been stored, in order to access the door with any type of programmer (T-NFC, ET-DSEL, LabelTools App), you will have to know its encoding. - Page 16 T-NFC Made in Italy S.p.A Via Ilariuzzi, 17/A - S. Pancrazio P .se - 43126 PARMA - ITALIA CERTIFIED COMPANY QUALITY SYSTEM Tel. (+39) 05 21/ 67 52 - Fax (+39) 05 21/ 67 52 22 UNI EN ISO 9001:2000...