Related Manuals for Label Neptis SMP
Summary of Contents for Label Neptis SMP
- Page 1 AUTOMATIC SWING DOORS FOR PEDESTRIANS English Translation of the ORIGINAL INSTRUCTIONS NEPTIS-SMP-16005_GB_Rel.1.0_07/2014 - CD0420GB...
- Page 2 RECOMMENDATIONS THIS INSTRUCTION MANUAL IS INTENDED FOR THE FINAL USER OF A LABEL AUTOMATIC SWING DOOR SYSTEM; IT IS UNDERSTOOD THAT INSTALLATION AND TESTING MUST HAVE BEEN CARRIED OUT BY SPECIALISED PERSONNEL. GENERAL SAFETY WARNINGS BEFORE COMMISSIONING THE AUTOMATIC DOOR PLEASE CAREFULLY READ THIS MANUAL.
-
Page 3: Table Of Contents
Neptis AUTOMATIC SWING DOOR INDEX: INDICATIVE SYSTEM DESCRIPTION page TECHNICAL DATA AUTOMATIC DOOR OPERATION 3.1) NORMAL DOOR OPERATION 3.2) DOOR OPERATION IN NIGHT LOCK MODE 3.3) SUPPORT OPERATION FOR DISABLED PEOPLE PROGRAM SELECTORS 4.1) MANUAL PROGRAM SELECTOR 4.2) EV-MSEL MECHANICAL KEY SELECTOR 4.3) N-DSEL DIGITAL PROGRAMMER - USED LIKE PROGRAM SELECTOR 4.3.1) GENERAL PROGRAMMING MENU 4.3.2) PASSWORD... -
Page 4: Indicative System Description
1) INDICATIVE SYSTEM DESCRIPTION NOTE: The grey part indicates the survey zone of radar and sensors. EXTERNAL RADAR INTERNAL RADAR OPENING BUTTON PROGRAM SELECTOR SAFETY SENSOR FOR CLOSING SAFETY SENSOR FOR OPENING NEPTIS OPERATOR ELECTRIC LOCK FLOOR STOP 2) TECHNICAL DATA MODEL OPERATOR POWER SUPPLY 115/230Vac +/-10%, 50-60Hz... -
Page 5: Automatic Door Operation
3) AUTOMATIC DOOR OPERATION WARNING!! Always contact the assistance technician before commissioning the door, to learn how the automation works. Switch on the power supply by means of the system switch. The automation electronic control unit beeps shortly to indicate that the automatic door is powered. The first opening command starts a calibration cycle during which the door wing opening speed is very low until the end of the stroke, to find the stop points;... -
Page 6: Program Selectors
4) PROGRAM SELECTORS The program selector allows the door user to select the operating mode. The following can be used, according to the choice: manual selector integrated in Neptis operator side, EV-MSEL key mechanical selector or N-DSEL digital programmer. Each program selector is described in details below. 4.1) MANUAL PROGRAM SELECTOR The 3-position manual program selector is the basic solution provided for onboard operator. -
Page 7: N-Dsel Digital Programmer - Used Like Program Selector
4.3) N-DSEL DIGITAL PROGRAMMER – USED LIKE PROGRAM SELECTOR N-DSEL digital programmer can be installed in the system and used by the user like a program selector, as an alternative to manual and mechanical selector if you need a more complete tools in terms of functions and graphs. Select the automatic door operating mode by pressing once the button. - Page 8 Operation of other buttons located on N-DSEL program selector panel Pedestrian opening, used in double-leaf door automated device only To activate pedestrian opening, press the button. the symbol on the display indicates that the function is on. In a double leaf door, the first leaf (Master) only opens if the opening command is given by internal or external radar inputs.
-
Page 9: 1) General Programming Menu
4.3.1) GENERAL PROGRAMMING MENU The user can enter in the programming menu general when he wants to choose the preferred language in which to view texts that appear on the display, or when he wants to enable a password to prevent access to the use of N-DSEL digital programmer. DIAGRAM 1 EXIT EXIT... -
Page 10: 2) Password
4.3.2) PASSWORD To prevent changes in the work program of the door, you can set a password that must be entered each time you act on the N-DSEL programmer. To enable the password, do the following Press the SET button for 5 second to enter the programming menù general (see Diagram 1 in par. - Page 11 It is required to repeat the new password, so type the previous combination again. If the password typed is correct, “PASSWORD OK” is shown on display for one second, thus reverting to the PASSWORD MANAGEMENT section; through the EXIT button the general programming menu is restored.
-
Page 12: 3) Language
ENABLING USER (primary and service) PASSWORD USAGE Select “PASSWORD ON / OFF” Press OK (F1) button. Type the primary password Press ON button to enable the user password usage and return to PASSWORD MANAGEMENT menu. To return to work program view, press EXIT button twice. -
Page 13: Operation In Case Of Power Supply Failure
5) OPERATION IN CASE OF POWER SUPPLY FAILURE NEPTIS SMP VERSION In case of power supply failure the door can be opened and closed manually. If the door is equipped with an electric lock, use the special key to unlock it. -
Page 14: Notification Of Errors And Operation Problems
6) NOTIFICATION OF ERRORS AND OPERATION PROBLEMS SOLUTION PROBLEM LIKELY CAUSE The motion sensors (radars) or Check that the radars or the The door opens but it doesn't close back. the closing safety sensor detect sensors are not engaged. the presence of an object or of a person. -
Page 15: Maintenance
7) MAINTENANCE The maintenance plan must be observed to ensure the life and proper operation of the automatic door. It is recommended to take a maintenance contract that providing for periodic intervention on the system by specialised technicians. If the user has the program selector N-DSEL, will be advised of the need for maintenance when the display shows the message "SCHEDULED MAINTENANCE". - Page 16 Made in Italy S.p.A. Via Ilariuzzi, 17/A - S. Pancrazio P .se - 43126 PARMA - ITALIA Tel. (+39) 05 21/ 67 52 - Fax (+39) 05 21/ 67 52 22 infocom@labelspa.it - www.labelspa.com...