Related Manuals for Label NEXT 75
Summary of Contents for Label NEXT 75
- Page 1 NEXT 75 NEXT 150 NEXT 120s Automation for indoor automatic swing doors TRANSLATION OF THE ORIGINAL INSTRUCTIONS NEXT 75/150/120S_EN_Rel.2.0_10/2020 - CD0750EN-MU...
- Page 2 Automatic Door Solutions RECOMMENDATIONS THIS INSTRUCTION MANUAL IS INTENDED FOR THE FINAL USER OF A LABEL AUTOMATIC SWING DOOR SYSTEM; IT IS UNDERSTOOD THAT INSTALLATION AND TESTING MUST HAVE BEEN CARRIED OUT BY SPECIALISED PERSONNEL. GENERAL SAFETY WARNINGS CAREFULLY READ THIS MANUAL BEFORE COMMISSIONING THE AUTOMATIC DOOR.
-
Page 3: Table Of Contents
Automatic Door Solutions CONTENTS: 1) INDICATIVE DESCRIPTION OF THE SYSTEM 2) TECHNICAL DATA 3) AUTOMATIC DOOR OPERATION 3.1) NORMAL DOOR OPERATION 3.2) DOOR OPERATION IN NIGHT LOCK MODE 3.3) COURTESY MODE FOR DISABLED 4) PROGRAM SELECTORS 4.1) MANUAL PROGRAM SELECTOR 4.2) MECHANICAL KEY SELECTOR EV-MSEL 4.3) DIGITAL PROGRAM SELECTOR ET-DSEL 4.4) DIGITAL PROGRAM SELECTOR T-NFC... -
Page 4: Indicative Description Of The System
CLOSING SAFETY SENSOR OPENING SAFETY SENSOR AUTOMATION NEXT ELECTRIC LOCK FLOOR STOP 2) TECHNICAL DATA AUTOMATION MODEL NEXT 75 NEXT 150 NEXT 120S POWER SUPPLY 115/230~, 50/60Hz POWER DIMENSIONS OF THE AUTOMATION (L x H x D) 420 x 60 x 74mm... -
Page 5: Automatic Door Operation
3) AUTOMATIC DOOR OPERATION WARNING!! Always contact the service technician before putting into service the door, to learn how the automation works. Switch on the power supply by means of the system switch. The automation electronic control unit beeps shortly to indicate that the automatic door is powered. The first opening command starts a calibration cycle during which the door opening speed is very low until the end of the motion, to find the stop point;... -
Page 6: Program Selectors
4) PROGRAM SELECTORS The program selector allows the user to select the operating mode of the door. Depending on the preference, it is possible to use the manual selector incorporated in the side cap of the automation NEXT, the mechanical key selector EV-MSEL, or the digital selector ET-DSEL or T-NFC. Each program selector is fully described below. -
Page 7: Digital Program Selector Et-Dsel
4.3) DIGITAL PROGRAM SELECTOR ET-DSEL Pressing briefly the button , select the automatic door operating mode. Whenever the button is pressed, you switch from a work program to the next. The work programs which can be selected using the button are described below Automatic bidirectional program The door automatically opens after an opening command. -
Page 8: Digital Program Selector T-Nfc
4.4) DIGITAL PROGRAM SELECTOR T-NFC DAILY USE The selector T-NFC enables to select for daily use 6 different types of programs: AUTO: ENTRY: The door opens and closes automatically The door opens and closes automatically in both flow directions with all sensors only in entry direction: active. -
Page 9: Selector Et-Dsel General Programming Menu
4.5) SELECTOR ET-DSEL GENERAL PROGRAMMING MENU The user can enter the general programming menu when he wishes to select the desired language for the texts that appear on the display, or when he wishes to enable a password to prevent any unauthorised access to the digital selector ET-DSEL. DIAGRAM 1 SECTION RESERVED FOR SECTION RESERVED FOR... -
Page 10: Dsel Selector User Password Management
4.6) ET-DSEL SELECTOR USER PASSWORD MANAGEMENT To prevent the door work program from being modified, it is possible to set a password that must be entered every time the selector ET-DSEL is used. To enable the password, perform the operations listed below: Press the SET button for 5 seconds to access the general programming menu (see Diagram 1 at para. - Page 11 HOW TO CHANGE THE SERVICE PASSWORD • Select “SERVICE PASSWORD” • Press OK (F1). • Enter the primary password • Enter the new service password, selecting a combination of 5 characters from the letters A-B-C-D. • You are prompted to repeat the new password, so enter again the previous combination. •...
-
Page 12: T-Nfc Selector User Password Management
4.7) T-NFC SELECTOR USER PASSWORD MANAGEMENT The selector T-NFC enables to prevent the work program change by means of a password. This function is useful if you want to prevent unauthorized persons from setting the work program of the door. To do this, you need to enable the user password with the following steps: Press and hold button D for approximately 2 seconds. -
Page 13: Language
4.8) LANGUAGE To select the language on the selector ET-DSEL, perform the operations listed below: 1. Press the button for 5 seconds to enter the general programming menu. (see Diagram 1 in the previous paragraph) 2. Press the button F1 three times to go to the Language sub-menu. 3. -
Page 14: Notification Of Errors And Operational Issues
6) NOTIFICATION OF ERRORS AND OPERATIONAL ISSUES PROBLEM LIKELY CAUSE SOLUTION The motion radars or the closing safety Check that the radars or the sensors are The door opens but it doesn't close back. sensor detect the presence of an object or not engaged. -
Page 15: Maintenance
7) MAINTENANCE The maintenance plan must be observed to ensure the service life and the safe operation of the automatic door. It is recommended to sign a maintenance contract providing for periodic intervention on the system by specialised technicians. If the user has the program digital selector ET-DSEL or T-NFC, he will be warned about the expiry of the maintenance interval when the message "SCHEDULED MAINTENANCE"... - Page 16 LABEL service centre NEXT Made in Italy S.p.A Via Ilariuzzi, 17/A - S. Pancrazio P .se - 43126 PARMA - ITALIA Tel. (+39) 05 21/ 67 52 - Fax (+39) 05 21/ 67 52 22 infocom@labelspa.it - www.labelspa.com...