Page 2
Parker or its subsidi- aries or authorized distributors. To the extent that Parker or its subsidiaries or authorized distributors provide component or system options based upon data or specifica-...
Code Code power down power down Code Signal Flow direction +/- 10V 0...+10V -> P-A +/- 20mA 0...+20mA -> P-A 4...20mA 12...20mA -> P-A Code Seal for HFC fluid D_FP_20 5715-658 UK.indd CM 06.11.13 Parker Hannifin Corporation Hydraulic Controls Division...
Cable Length max. [m] 50 For applications with p >35 bar (max 250 bar) the Y-port has to be connected and the plug in the Y-port has to be removed. D_FP_20 5715-658 UK.indd CM 06.11.13 Parker Hannifin Corporation Hydraulic Controls Division...
Prop. Directional Control Valve Operation Manual Series DFplus Block Diagram of Integral Electronics Parker D*FP proportional directional control valves have an integral electronic and require only one sole Code 0 (6+PE) electrical common for the control system. Different flow sizes, power down configuration as well as command signal options are available to achieve an optimal adaption for different applications.
< 25°C varying humidity as well as 6 months varying temperature < 35°C Outdoor storage or within sea and tropical climate will lead to corrosion and might disable the valve! D_FP_20 5715-658 UK.indd CM 06.11.13 Parker Hannifin Corporation Hydraulic Controls Division...
Series DFplus 4. Mounting / Installation Scope of Supply Please check immediately after receiving the valve, Parker offers bolt kits: if the content is matching with the specified scope D1FP: BK375 / D3FP: BK385 of supply. The delivery includes: • Tighten the bolts crisscross with the following •...
Skinning lengths for the connecting cable: For the workmanlike termination of the crimp contacts the tool # 932 507-001 – supplier: Hirschmann – is required. Do not disconnect cable socket under tension! D_FP_20 5715-658 UK.indd CM 06.11.13 Parker Hannifin Corporation Hydraulic Controls Division...
It is necessary to use a low ohmic potential connection between control unit and machine frame to prevent earth loops (cross section AWG 6). D_FP_20 5715-658 UK.indd CM 06.11.13 Parker Hannifin Corporation Hydraulic Controls Division...
Page 13
Preferable the enable signal should be switched on installation of additional safety check valves. together with the hydraulic pressure supply. This D_FP_20 5715-658 UK.indd CM 06.11.13 Parker Hannifin Corporation Hydraulic Controls Division...
Page 14
The command input signal needs to be filtered as well as free of inductive surges and modulations. Due to the sensitivity of the valve a high signal quality is recommended, this will prevent malfunction. D_FP_20 5715-658 UK.indd CM 06.11.13 Parker Hannifin Corporation Hydraulic Controls Division...
Page 15
Wiring diagram of current command input +20...0...-20 mA Code 0 (6 + PE) Code 7 (6 + PE) Wiring diagram of current command input +20...0...-20 mA Code 5 (11 + PE) D_FP_20 5715-658 UK.indd CM 06.11.13 Parker Hannifin Corporation Hydraulic Controls Division...
Page 16
Wiring diagram of current command input 4...12...20 mA Code 0 (6 + PE) Code 7 (6 + PE) Wiring diagram of current command input 4...12...20 mA Code 5 (11 + PE) D_FP_20 5715-658 UK.indd CM 06.11.13 Parker Hannifin Corporation Hydraulic Controls Division...
Page 17
0...+100 % 0...+10 V signal 0...-100 % 0...-10 V P-A/B-T overloaded P-B/A-T +22...30 V (U preferred hydraulic initial (fail safe) state - depends on type D_FP_20 5715-658 UK.indd CM 06.11.13 Parker Hannifin Corporation Hydraulic Controls Division...
The overcurrent shutoff condition may be resetted by the actions below: Code 0: Temporary disconnection of the supply voltage. Code 5: Temporary disconnection of the enable signal. Code 7: Temporary disconnection of the enable signal. D_FP_20 5715-658 UK.indd CM 06.11.13 Parker Hannifin Corporation Hydraulic Controls Division...
It is recommended to flush the long pipelines by short circuiting the pressure and return lines, especially for large, central pressure oil stations. This prevents the installation dirt from entering the valve. D_FP_20 5715-658 UK.indd CM 06.11.13 Parker Hannifin Corporation Hydraulic Controls Division...
/ replace plug feed cable interrupted fix feed cable X X X X X X X wiring sequence incorrect correct wiring sequence X feed cable without shielding change cable grade D_FP_20 5715-658 UK.indd CM 06.11.13 Parker Hannifin Corporation Hydraulic Controls Division...