ABB REL300 Instruction Manual page 178

I.L. 40-385.7
RP Enable readouts in primary values . . . . . . . . . . . . . . . . . . . 4.5.2, 5.2.7
RS1 Test function for simulating receipt of receiver 1 input . . . . . . . . . 3.5.1f, A (1.2.2)
RS1.2 Test function for simulating receipt of receiver 1 and 2 inputs . . . . .
RS2 Test function for simulating receipt of receiver 2 input . . . . . . . . .
RT Inner blinder setting (ohms) for 3-phase load restriction . . . . . . . . 2.10, 3.4.17, 5.1.6, A (1.4)
RU Outer blinder setting (ohms) for out-of-step option. . . . . . . . . . . 2.10, 3.4.17, 5.1.6, A (1.4)
RX1 Pilot channel receiver #1 input, same as RCVR#1. . . . . . . . . . .
RX2 Pilot channel receiver #2 input, same as RCVR#2. . . . . . . . . . .
SBP Stub bus protection (89b) . . . . . . . . . . . . . . . . . . . . . . . 1.3.2, 3.4.7, 4.3, 4.6.2, 5.2.30, A (1.1.14),
SCF Stub Bus with standard Close-into-fault . . . . . . . . . . . . . . . . 3.4.7
SCFT Stub Bus with CIF and Timer. . . . . . . . . . . . . . . . . . . . . . 3.4.7
SEND Carrier send output. . . . . . . . . . . . . . . . . . . . . . . . . . . 3.7, 3.5.1b, 3.5.2b, 3.5.3b, 4.5.4, 4.6.4,
SET Enable/Disable Remote/Local Setting . . . . . . . . . . . . . . . . . 4.7
SETR Enable INCOM remote setting capability. . . . . . . . . . . . . . . . 4.7, 5.2.25
SPF Sound phase fault trip . . . . . . . . . . . . . . . . . . . . . . . . . 3.4.18, A (1.3.1)
SPR Single-pole and 3-pole trip, single-pole reclosing only . . . . . . . . . 2.8, 3.4.18, Table 3-3, 5.2.10, A (1.3)
SPT Single-Pole Trip for single-pole application . . . . . . . . . . . . . . 2.8, 3.4.18, Table 3-3, 5.2.11
SR3R Single-pole and 3-pole trip, reclosing for all faults . . . . . . . . . . . 2.8, 3.4.18, Table 3-3, 5.2.10
SRI Single-phase Reclose Initiate, Same as RI-1 . . . . . . . . . . . . . 2.8, 3.4.18, Table 3-3
STOP Carrier Stop Signal . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.2.2, 4.5.4, A (1.1.3)
STUB Stub Bus Protection same as SBP (89b). . . . . . . . . . . . . . . . 3.4.7, 5.2.30
STYP System type setting (3ZNP, Z1E, POTT, PUTT, BLK) . . . . . . . . . 3.3, 3.3.4, 3.5, 5.2.15
T1 Zone 1 delay trip timer . . . . . . . . . . . . . . . . . . . . . . . . . 2.6, 3.3.1, 5.2.21
T2G Zone 2 ground timer delay setting (seconds) . . . . . . . . . . . . . 2.6, 3.3.2, 5.1.8a, 5.2.22
T2P Zone 2 phase timer delay setting (seconds) . . . . . . . . . . . . . . 2.6, 3.3.2, 5.1.8a, 5.2.22
T3G Zone 3 Ground Timer . . . . . . . . . . . . . . . . . . . . . . . . . 2.6, 3.3.3, 5.1.8b, 5.2.23
T3P Zone 3 Phase Timer . . . . . . . . . . . . . . . . . . . . . . . . . . 2.6, 3.3.3, 5.1.8b, 5.2.23
TBM Transient Block Memory . . . . . . . . . . . . . . . . . . . . . . . . 3.5.1e,3.5.3b, 3.5.5
TK Transmitter Keying . . . . . . . . . . . . . . . . . . . . . . . . . . .
TRIP Trip Action . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TRIPB Trip on Phase B . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TRIP B-1 Trip relay B-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TRSL Trip Seal-in Trip signal and seal-in if trip current presented . . . . . .
TTYP Trip Type, and reclose selection (1PR, 2PR, 3PR, etc.) . . . . . . . . 2.8, 3.4.14, Table 3-3, 5.2.10, 5.3.2,
UBLK Unblock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.5.1, 3.20c
VBFI Power Supply voltage to Breaker Failure Initiate. . . . . . . . . . . .
VF Fault Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
VLN Line-to-neutral voltage . . . . . . . . . . . . . . . . . . . . . . . . .
VTR Voltage Transformer Ratio . . . . . . . . . . . . . . . . . . . . . . .
Index-4
S
T
U
V
A (2.1.4)
A (1.2)
Table 5-2