Digital Watchdog STAR-LIGHT DWC-V4283WTIR Quick Start Manual

Quick Start Guide
DW® Universal HD over Coax® Snapit™
vandal dome cameras
DWC-V4283WTIR DWC-V4283WD
WHAT'S IN THE BOX
Hexagonal Mounting
1
wrench Torx Wrench template DC Plug Cable
Torx Wrench DC Plug Cable Test Video Cable
Screws and
DC plug
1 plastic anchors
cable
- 4pcs
Torx Wrench DC Plug Cable
Test Video Cable
Sunshield cover &
Torx Wrench DC Plug Cable Test Video Cable
Template Sheet Manual
Screw &
Moisture
Template Sheet Manual
Test video absorber and
1
cable absorber guide
Torx Wrench
(recommended)
Sunshield cover &
DC Plug Cable Test Video Cable
Screw &
Template Sheet Manual
Screw & Moisture absorber &
Template Sheet Manual
Absorber Guide
Star wrench Quick set up
1
drive guide
Template Sheet
Screw & Moisture absorber &
Manual
Absorber Guide
NOTE: Download all your support materials and tools in one place.
1. Go to: http://www.digital-watchdog.com/resources.
2. Search your product by entering the part number in
the 'Search by Product' search bar. Results for
applicable part numbers will populate automatically
based on the part number you enter.
3. Click 'Search'. All supported materials, including manuals
and quick start guide (QSGs) will appear in the results.
Attention: This document is intended to serve as a quick reference for initial
setup. It is recommended that the user read the entire instruction manual for
complete and proper installation and usage.
Tel: +1 (866) 446-3595 / (813) 888-9555
Technical Support Hours:
9:00AM – 8:00PM EST, Monday through Friday
STEP 1 – PREPARING TO MOUNT THE CAMERA
1. The mounting surface must withstand five times the camera weight.
2. Pay attention to the cables. The can easily become caught and damaged.
Any damage may cause a short or fire.
3. Install the moisture absorber in the base of the camera's lens.
a. Remove the moisture absorber from the packaging.
b. Place the moisture absorber around the base of the camera's lens module.
NOTE:
WARNING:
Sunshield cover &
Torx Wrench DC Plug Cable
Test Video Cable
1
Sunshield cover &
Test Video Cable
Sunshield cover &
Screw & Moisture absorber &
Template Sheet Manual
1 set
Sunshield cover &
Screw & Moisture absorber &
Absorber Guide
Moisture absorber &
Absorber Guide
1
Sunshield cover &
DC Plug Cable Test Video Cable
Moisture absorber &
4. Detach the camera's dome cover by loosening the screws on each side of the
Absorber Guide
dome.
1
5. Using the mounting template sheet or the camera itself, mark and drill the
Screw & Moisture absorber & necessary holes in the wall or ceiling.
Manual
Absorber Guide
STEP 2 – CABLING THE CAMERA TO EXTERNAL DEVICES
Pass the wires through the mount bracket and make all necessary connections. Connect the BNC cable and power cables to the camera.
digital-watchdog.com
The camera will generate enough heat to dry moisture
during operation. In most cases it will not need the
moisture absorber for more than the first day. In cases
where the camera can experience a moisture issue,
users must keep the moisture absorber in the camera.
The moisture absorber has an approximately 6-month
life cycle, varying depending on the environment.
It is highly recommended that you install the moisture
absorber when mounting the camera. The moisture
Absorber attachment point
absorber prevents moisture from being captured
inside the camera's housing, which may cause image
performance issues and damage the camera.
Absorber Guide
Please attach the card type absorber to
attachment point as the picture.
Power Requirements
DC12V/AC24V dual voltage
Quick Start Guide
Protective sheet
Protective film
Power Consumption
DC12V (LED off): 3.0W
DC12V (LED on): 5.2W
AC24V (LED off): 2.3W
AC24V (LED on): 4.6W