Bkav AI VIEW ULTRA ZOOM BULLET S200 Installation Manual

Ai-based camera

Advertisement

Quick Links

ULTRA ZOOM bullet
AI-based Camera
Qualcomm products contained herein are products of Qualcomm Technologies, Inc. and/or its subsidiaries.
Qualcomm is a trademark of Qualcomm Incorporated, registered in the United States and other countries.
The Made with Qualcomm Technologies logo is a trademark of Qualcomm Incorporated.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the AI VIEW ULTRA ZOOM BULLET S200 and is the answer not in the manual?

Questions and answers

Summary of Contents for Bkav AI VIEW ULTRA ZOOM BULLET S200

  • Page 1 ULTRA ZOOM bullet AI-based Camera Qualcomm products contained herein are products of Qualcomm Technologies, Inc. and/or its subsidiaries. Qualcomm is a trademark of Qualcomm Incorporated, registered in the United States and other countries. The Made with Qualcomm Technologies logo is a trademark of Qualcomm Incorporated.
  • Page 2 INSTALLATION GUIDE Model: S200 Product Number: 0233...
  • Page 3: Product Kit

    PRODUCT KIT Camera Wall bracket Safety cable WALL DECAL FOR DRILLING POSITION ULTRA ZOOM bullet AI-based Camera Ø10 mm, 4 holes Qualcomm products contained herein are products of Qualcomm Technologies, Inc. and/or its subsidiaries. Qualcomm is a trademark of Qualcomm Incorporated, registered in the United States and other countries. The Made with Qualcomm Technologies logo is a trademark of Qualcomm Incorporated.
  • Page 4 PRODUCT KIT Water supply tank Water supply tank accessories Power supply (Optional) (Optional) (Optional) IR led Wi-Fi Antenna Set 4 of screws and anchors Hex key (Optional) (Optional)
  • Page 5: Technical Specifications

    TECHNICAL SPECIFICATIONS POE IEEE 802.3af/802.3at Power supply 30 - 80W depends on IR LED module (IR LED: 6, 12, 24, 48W) Protection standards IP66, IK10 Resolution, frame rate FHD 1920x1080, 60 fps Optical zoom Focal length 4.5 - 148.5mm ± 5% Angle of view (horizontal - vertical) Near: 60.1°...
  • Page 6: Product Overview

    PRODUCT OVERVIEW GPS antenna Water and dust camera shield Lens protection Lens wiper Safety cable Wall bracket...
  • Page 7 INSTALLATION GUIDE Step 1: Pass the PoE network cable through the center position on the decal. Put the decal onto the place need to install and drill the expansion hole (Figure 1). Step 2: Route the network cable through the bracket and fix the screw to the bracket (Figure 2). Drilling position decal Network cable...
  • Page 8 INSTALLATION GUIDE Step 3: Put the camera onto the fixed bracket with hinge bolt and safety cable (Figure 3). Step 4: Tighten the screw that fixes the camera body to the bracket (Figure 4).
  • Page 9 INSTALLATION GUIDE Step 5: Connect the PoE cable to the signal stand-by (Figure 5). Step 6: Tighten the screw that fixes the camera body to the installation position (Figure 6). Decal...
  • Page 10 ADJUSTING THE CAMERA VIEWING ANGLE 65° Loosen the screw, then turn 130° camera to the right position...
  • Page 11 THE MEMORY CARD AND RESET INSTALLATION Reset installation: Open the protective cover that protects the camera against dust and water to reset the device. Memory card: Open the protective cover, you can find the location of Micro SD card. Reset installation Mirco SD card Note:...
  • Page 12 IR LED INSTALLATION GUIDE (*) Step 1: Remove fixing screws and the IR LED connector protection element (Figure 1). Step 2: Insert IR LED into the camera and fix with 2 screws as (figure 2). Note: It is recommended that user install IR LED on the camera before mounting the camera on the wall, the following installation steps are similar to these steps above.
  • Page 13 POE INSTALLATION GUIDE Voltage: 240V 50/60Hz Router...
  • Page 14 WATER TANK INSTALLATION GUIDE Step 1: Fix the components to fix the water tank frame to the installation place, tighten the components in figure 1). Step 2: Place the water tank in the frame then connect the water hose to the camera (figure 2). Water tank frame Steel fasteners Sprinkler head...
  • Page 15: Password Setting

    ACCESSING THE CAMERA Password setting Using your web browser, access the camera's default IP: 192.168.1.168 Note: To complete the installation steps for the camera, refer to the User Manual. The system will ask you to reset the password on your initial access. When the "Administrator password change"...
  • Page 16: Software Installation

    SOFTWARE INSTALLATION Login screen When accessing the camera, a login window will appear. Enter your user name and password to access the camera. 1. Enter "admin" in the <User name> box. 2. Enter your chosen password in <Password> box. 3. Click User name Password...
  • Page 17: Safety Information

    Improper installation may cause damage to the product. Contact Bkav's customer support or authorized Bkav agents if you experience any problems. This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC rules.
  • Page 20 BKAV CORPORATION Address: 2nd Floor - HH1 Building, Yen Hoa Ward, Cau Giay District, Ha Noi, Viet Nam Website: www.aiview.ai Email: aiview@bkav.com...

This manual is also suitable for:

0233

Table of Contents