Culligan Aquasential Select Plus Iron-OX5 Owner's Manual page 15

Culligan Aquasential Select Plus Sulfur-OX3 Filter
Culligan knows the more informed you are about your water treatment systems, the more confident you will be about its performance� It's because
of this and more than seventy years of commitment to customer satisfaction that Culligan is providing this Performance Data Sheet to its customers�
NOTE!
Read this Performance Data Sheet and compare the capabilities of this unit with your actual water treatment needs.
It is recommended that before purchasing a water treatment unit, you have your water supply tested to determine
your actual water treatment needs.
Manufacturer: Culligan International Company
9399 W� Higgins Rd�, Suite 1100
Rosemont, IL 60018 USA
(847) 430-2800
www�culligan�com
Product: Culligan Select Plus
Substance Reduction
This system has been tested according to NSF/ANSI Standard 42 for the reduction of the substances listed below� The concentration
of the indicated substances in water entering the system was reduced to a concentration less than or equal to the permissible limit for
water leaving the system, as specified in NSF/ANSI Standard 42�
While testing was performed under standard laboratory conditions, actual performance may vary�
Name of
Substance
Hydrogen Sulfide
Capacity:
Flow Rate:
Rated Pressure Drop:
Operating Conditions
Water Pressure Limits:
Temperature Limits:
Electrical Characteristics:
The Culligan Select Plus Sulfur-OX3 water filter system has been tested and certified by WQA against NSF/ANSI
Standard 372, CSA B483�1, and NSF/ANSI Standard 42 for the effective reduction of hydrogen sulfide up to 500
gallons as verified and substantiated by test data�
The Culligan Outdoor Select Plus Sulfur-OX3 water filter system has been tested and certified by WQA against
NSF/ANSI Standard 372 and Standard NSF/ANSI 42 for the effective reduction of hydrogen sulfide up to 500
gallons as verified and substantiated by test data�
The Culligan Select Plus Sulfur- OX3 water filter system has been certified by WQA against NSF/ANSI
Standard 372, CSA B483�1, and NSF/ANSI Standard 42 for the effective reduction of hydrogen sulfide up to
500 gallons as verified and substantiated by test data�
The Culligan Outdoor Select Plus Sulfur- OX3 water filter system has been certified by WQA against NSF/ANSI Standard 372 and
Standard NSF/ANSI 42 for the effective reduction of hydrogen sulfide up to 500 gallons as verified and substantiated by test data�
Performance Indicator: If water flow decreases or a noticeable taste change occurs, the filter should be reconditioned� If conditions
do not improve, contact your local Culligan dealer� They can determine if your filter requires servicing� Do not use with water that is
microbiologically unsafe or of unknown quality without adequate disinfection before or after the system�
Reconditioning cycle Frequency: Reconditioning frequency is recommended every three days but can vary with local water conditions�
Refer to your Owner's Guide and printed limited Warranties (P/N 01040684) for more specific product information� To avoid contamination
from improper handling and installation, your system should only be installed and serviced by your Culligan dealer� Performance will vary
based on local water conditions� The substances reduced by this product are not necessarily in your water�
Buyer Signature _______________________________________________________________________ Date ____________________
Seller Signature _______________________________________________________________________ Date ____________________
15
01040684 A 06/21
®
Sulfur-OX3 Filter
Influent Challenge
Concentration
1�0-3�0 mg/L ± 10%
500 gallons
4 gpm
4 gpm @ 2�9 psi
20 - 60 psi (140)
33 - 120° F (1 - 50° C)
24V/60Hz, 10W
Reduction Requirement
0�05 mg/L
Average Reduction
Percentage
96�2%