Eaton Cutler-Hammer IQ DP-4000 Instructions For Installation, Operation And Maintenance page 5

LIST OF TABLES
TABLE 1.A
TABLE 1.B
TABLE 2.A
TABLE 2.B
TABLE 2.C
TABLE 3.A
TABLE 5.A
TABLE 5.B
TABLE 5.C
TABLE 5.D
TABLE 5.E
TABLE 5.F
TABLE 5.G
TABLE 5.H
TABLE 5.I
TABLE 5.J
TABLE 5.K
TABLE 5.L
TABLE 5.M
TABLE 5.N
TABLE 5.O
TABLE 5.P
TABLE 5.Q
TABLE 5.R
TABLE 5.S
TABLE 5.T
TABLE 5.U
TABLE 5.V
TABLE 5.W
TABLE 5.X
TABLE 5.Y
TABLE 5.Z
TABLE 5.AA
TABLE 6.A
TABLE 6.B
LIST OF FIGURES
FIGURE 2.1
FIGURE 2.2
FIGURE 3.1
FIGURE 3.2
FIGURE 3.3
FIGURE 3.4
FIGURE 3.5
FIGURE 4.1
FIGURE 4.2
FIGURE 4.3
FIGURE 4.4
FIGURE 4.5
FIGURE 4.6
FIGURE 4.7
FIGURE 4.8
FIGURE 4.9
FIGURE 4.10
FIGURE 4.11
MODEL COMPARISON..............................................................................1
PARTS AND ACCESSORIES .....................................................................2
GENERAL SPECIFICATIONS....................................................................6
PROTECTION FUNCTION (TRIP) SPECIFICATIONS ............................6
METERING SPECIFICATIONS..................................................................7
ALARM CODES ........................................................................................11
SETPOINT MASTER SHEET ...................................................................21
GENERAL SYSTEM FUNCTIONS ..........................................................22
ALARM FUNCTIONS ...............................................................................22
OPTIONAL I/O FUNCTIONS ...................................................................22
SETPOINT SWITCH SETTINGS..............................................................23
AC LINE VOLTAGE .................................................................................24
POWER DEMAND INTERVALS FOR WATTS, VARS AND VA.........25
DEMAND SAMPLING INTERVAL FOR IA, IB, AND IC......................25
ALARM RELAY MODE SETTING..........................................................26
LATCHED/UNLATCHED SETTINGS .....................................................27
ACTIVATE ON OVERVOLTAGE SETTINGS........................................27
ACTIVATE ON UNDERVOLTAGE SETTINGS.....................................27
ACTIVATE ON VOLTAGE PHASE LOSS SETTINGS ..........................27
ACTIVATE ON VOLTAGE PHASE UNBALANCE SETTINGS ...........27
ACTIVATE ON VOLTAGE PHASE REVERSAL SETTINGS ...............28
ACTIVATE ON CURRENT PHASE LOSS SETTINGS ..........................28
ENABLE/DISABLE ALARM SETTINGS ................................................28
ALARM DELAY SETTINGS ....................................................................28
RESET DELAY SETTINGS ......................................................................28
OVERVOLTAGE DETECTION LEVEL SETTINGS ..............................29
UNDERVOLTAGE DETECTION LEVEL SETTINGS............................29
VOLTAGE PHASE UNBALANCE DETECTION LEVEL SETTINGS ..29
RESET THRESHOLD SETTINGS ............................................................30
PULSE INITIATOR PARAMETER SELECTION SETTINGS ................35
LOAD SHED AND RESTORE LOAD SETTINGS ..................................36
LOAD SHED PARAMETER SELECTION SETTINGS...........................38
PULSE INITIATOR RATE SELECTION SETTINGS..............................38
INITIAL POWER-ON TROUBLESHOOTING ........................................40
OPERATIONAL TROUBLESHOOTING .................................................41
THREE PHASE POWER MODULE FOR MODELS 4030 AND 4130......3
REAR ACCESS AREA OF CHASSIS.........................................................4
OPERATOR PANEL ....................................................................................8
POWER QUADRANTS, MATHEMATICAL ...........................................10
POWER QUADRANTS, POWER ENGINEER'S SIGN CONVENTION10
INDUCTION MOTOR LOAD ...................................................................11
POWER DISTRIBUTION ..........................................................................11
CHASSIS CUTOUT DIMENSIONS..........................................................12
SIDE PROFILE DEPTH DIMENSIONS ...................................................13
POWER MODULE DIMENSIONS ...........................................................13
3-PHASE, 3-WIRE (UP TO 600 VOLTS) WIRING DIAGRAM..............14
3-PHASE, 3-WIRE (ABOVE 600 VOLTS) WIRING DIAGRAM ...........15
3-PHASE, 3-WIRE (UP TO 600 VOLTS) WIRING DIAGRAM..............15
3-PHASE, 3-WIRE (ABOVE 600 VOLTS) WIRING DIAGRAM ...........16
3-PHASE, 4-WIRE (UP TO 600 VOLTS) WIRING DIAGRAM..............16
3-PHASE, 4-WIRE (ABOVE 600 VOLTS) WIRING DIAGRAM ...........17
3-PHASE, 3-WIRE (UP TO 600 VOLTS) WIRING DIAGRAM..............17
3-PHASE, 3-WIRE (ABOVE 600 VOLTS) WIRING DIAGRAM ...........18
i i i