Advertisement
Mounting instructions for the 2016 Rocky Mountain Saddle Bags #M1016 with our A146
*READ THROUGHLY BEFORE ATTACHING BAGS TO RACKS*
*For best results take a test ride before putting your Rocky Mountain Saddle Bags to use*
*Helpful hint: Before you begin stuff each bag with a sleeping bag or quilt to give it body*
FIG.1 Right Side
*Please note the various parts of the saddlebag. Since the left and right bags are identical only one is shown.
Universal Saddle Bag Straps. Patents Pending.
Thank you for purchasing the Rocky Mountain Saddle Bags
*The mounting is the same for both left and right bags*
A properly mounted pair of Rocky Mountain Saddle Bags.
Bag Orientation
FIG.2 Left Side
FIG.3
Seat straps
Handle
2" D-Rings-Back (2)
2" D-Rings-Front (2)
1" Cam buckles (2 on each front patch)
1" Side mounting straps (2 on each side)
Saddle bag strap with wolf logo (2 on each side)
1
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Wolfman M1016
Summary of Contents for Wolfman M1016
- Page 1 Mounting instructions for the 2016 Rocky Mountain Saddle Bags #M1016 with our A146 Universal Saddle Bag Straps. Patents Pending. Thank you for purchasing the Rocky Mountain Saddle Bags *READ THROUGHLY BEFORE ATTACHING BAGS TO RACKS* *For best results take a test ride before putting your Rocky Mountain Saddle Bags to use*...
- Page 2 ATTACHING ROCKY MOUNTAIN SADDLE BAGS TO VIRTUALLY ANY MOTORCYCLE SIDE RACK 1- Press the cam buckles on the upper and lower mounting patches and loosen the 1” Side mounting straps. FIG.4 Loosen 1” cam buckles (4 per bag) 2- Place bags over the seat and/or rear rack. Depending on the width of your motorcycle, you may need to adjust the height of each bag.
- Page 3 FIG.6 FIG.7 5- Tighten the 1” Mounting strap which will tighten the saddle bag strap and the ¾” slide is captured, as shown in FIG.8 6-Repeat steps 6-8 for all saddle bag straps (4 per bag). 7-Correctly mounted top and bottom saddle bag straps. FIG.9...
- Page 4 FIG.9 8- Tighten the 1” Side mounting straps threaded through each cam buckle on front of each bag. FIG.10 Tighten straps to secure and compress bag to the rack (pull side mounting straps away from the cam buckles in the direction of the arrows). FIG.10...
- Page 5 9- Thread excess webbing through plastic loop and strap keeper, repeat this for all excess webbing. FIG.11 FIG.11 4-Straps per bag Plastic loop and strap keeper 10- Tighten the 2” wide seat straps by pulling the webbing away from the 2” buckles. You can pull both ends to tighten the webbing.
- Page 6 16- Use the handles to remove the bags away from the side racks. FIG.14 FIG.14 Note: All of the mounting straps on the Wolfman Rocky Mountain Saddle Bags are removable and replaceable. Extra mounting kits can be purchased from us.
- Page 7 The Rocky Mountain Saddle Bags have 2” D-rings incorporated into the outside and bikes-side the bags. FIG.3 These are for attaching additional Wolfman products such as a Small or Medium Rolie Bag with our Wolfy SnapHook Kit (for quick on/off) (FIG.15) or our Bottle Holster for additional fuel or water. Also there are four, one-inch plastic loops on the side of each bag that are for mounting our Bottle Holster to hold either a fuel or water bottle.
Need help?
Do you have a question about the M1016 and is the answer not in the manual?
Questions and answers