Textron Cessna 208B Manual
  1. Manuals
  2. Brands
  3. Textron Manuals
  4. Aircrafts
  5. Cessna 208B
  6. Manual

Textron Cessna 208B Manual

Hide thumbs Also See for Cessna 208B:

Advertisement

Table of Contents

Caravan
TITLE
LOW-PROFILE TKS ICE PROTECTION SYSTEM INSTALLATION FOR MODEL 208B AIRPLANES WITH
PROVISIONS
EFFECTIVITY
Model
208B

DESCRIPTION

To provide the parts and instructions to install the TKS Ice Protection System.

APPROVAL

FAA approval has been obtained on technical data in this publication that affects airplane type design.
REFERENCE
SSP11-01R1
CHANGE IN WEIGHT AND BALANCE
The figures that follow show an estimated change only. For accurate weight and balance figures, you should
weigh the airplane before and after this Service Kit has been accomplished.
MODEL
. . . . . . . . . . . . . . . . .
WEIGHT INCREASE
. . . . . . . . .
ARM
. . . . . . . . . . . . . . . . . . . .
RESULTANT MOMENT
MOMENT/1000
. . . . . . . . . . . .
February 7, 2013
Original Issue: December 28, 2010
To obtain satisfactory results, procedures specified in this publication must be accomplished in accordance with accepted methods and
prevailing government regulations. Cessna Aircraft Company cannot be responsible for the quality of work performed in accomplishing the
requirements of this publication.
Cessna Aircraft Company, Customer Service, P.O. Box 7706, Wichita, Kansas 67277, U.S.A. (316) 517-5800, Facsimile (316) 942-9006
208B
+76.69 pounds
+141.70 inches
. . . . . . .
+10866.97 inch-pounds
+10.87 inch-pounds
COPYRIGHT © 2010
Serial Numbers
208B2014, 208B2016, 208B2032, 208B2056,
208B2105, 208B2115, 208B2120, 208B2133,
208B2168, 208B2171, 208B2182, 208B2202,
208B2208, 208B2211, 208B2250
SK208-179B
Page 1 of 119

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Cessna 208B and is the answer not in the manual?

Questions and answers

Related Manuals for Textron Cessna 208B

Summary of Contents for Textron Cessna 208B

  • Page 1 Caravan SERVICE KIT SK208-179B TITLE LOW-PROFILE TKS ICE PROTECTION SYSTEM INSTALLATION FOR MODEL 208B AIRPLANES WITH PROVISIONS EFFECTIVITY Model Serial Numbers 208B 208B2014, 208B2016, 208B2032, 208B2056, 208B2105, 208B2115, 208B2120, 208B2133, 208B2168, 208B2171, 208B2182, 208B2202, 208B2208, 208B2211, 208B2250 DESCRIPTION To provide the parts and instructions to install the TKS Ice Protection System. APPROVAL FAA approval has been obtained on technical data in this publication that affects airplane type design.
  • Page 2 SERVICE KIT SK208-179B MATERIAL INFORMATION The parts below cover installation for one airplane. NEW P/N QUANTITY DESCRIPTION OLD P/N DISPOSI- TION SK208-179B Kit, consisting of the following parts: AN525-10R10 Screw None None AN525-10R11 Screw None None AN525-10R12 Screw AN525-10R7 Screw None None AN525-10R8...
  • Page 3 SERVICE KIT SK208-179B Rivet None None MS20470A5-4A Rivet None None MS20426AD3-4A Rivet None None MS20470AD3-3A MS20470AD3-4A Rivet None None MS20470AD4-3A5 Rivet Various Discard MS20470AD4-4A Rivet None None MS20470AD4-4A5 Rivet None None MS20470AD4-6A Rivet MS20470AD5-8A Rivet MS20470AD5-9A Rivet MS21042-3 None None MS21044N3 None None...
  • Page 4 SERVICE KIT SK208-179B MS35206-229 Screw None None MS35207-258 Screw MS35207-273 Screw MS35489-6 Grommet NAS1033A3 Nutplate NAS1149C0363R Washer None None NAS1149D1290K Washer None None NAS1149F0316P Washer None None NAS1149F0332P Washer None None NAS1149FN832P Washer None None NAS43DD3-109FC Spacer NAS43DD3-18FC Spacer NAS6203-4 Bolt None None...
  • Page 5 SERVICE KIT SK208-179B S2357-2 Clamp Rivet S2456-4-2 Hose None None S2548-4-6.00 S2548-10 (R221240) Tubing S2562-3 (P610099) Tubing S2562-5 (P610022) Tubing S2800-942 Sealing Ring Same Discard S2800-943 Sealing Ring Same Discard S2906-4-2 Rivet None None S2974-8 Solder Sleeve None None S3001-13 Bracket S3017-6-6-6 None...
  • Page 6 SERVICE KIT SK208-179B 2601552-1 None None TKS Tank Vent Weldment 2601552-7 Filler Port Weldment None None 2601552-10 Doubler, Filler Port, 208B None None 2601553-12 Aft Drain Tube Assembly None None 2601553-14 TKS Accessory Pallet None None 2601553-3 TKS Filler Pallet None None 2601554-1...
  • Page 7 SERVICE KIT SK208-179B 2625027-1 Gurney Flap Wiring Assembly, 2677123-3* Windshield Ice Detec-LSWPNL 2677124-1* Wiring Assembly, TKS, 2677122-1 Discard ELEFUS 2677124-2* Wiring Assembly, TKS - LSWPNL 2680003-3 TKS Fairing MTG, Left None None 2680003-4 TKS Fairing MTG, Right None None 3D5304 Vortex Generator 336-00021-00 Contact...
  • Page 8 SERVICE KIT SK208-179B NAME NUMBER MANUFACTURER Epoxy Adhesive U000978S Cessna Aircraft Company To install grommets and to Cessna Service Parts and install vortex generators to the wings. Programs 5800 East Pawnee PO Box 1521 Wichita, KS 67218 Detergent, Mild Purchase Locally To clean wing panels Alodine U074093...
  • Page 9 SERVICE KIT SK208-179B NAME NUMBER MANUFACTURER Sealant U470637 Cessna Aircraft Company To use as a fillet seal from Cessna Service Parts and pitot tube to lens retainer Programs 5800 East Pawnee PO Box 1521 Wichita, KS 67218 Denatured Purchase locally To clean the leading edge Alcohol Sealant...
  • Page 10 SERVICE KIT SK208-179B Name Number Manufacturer T300-120-02 Clenching Tool Mandrel CAV Aerospace Inc. To fabricate TKS tubing (5/16 Inch) Clenching Tool (5/16 T300-120A CAV Aerospace Inc. To fabricate TKS tubing Inch) Clenching Tool (1/2 Inch) T300-144 CAV Aerospace Inc. To fabricate TKS tubing Clenching Tool (3/8 Inch) T300-145 CAV Aerospace Inc.
  • Page 11 SERVICE KIT SK208-179B Attach maintenance warning tags to the battery and external power receptacle that have "DO NOT CONNECT ELECTRICAL POWER - MAINTENANCE IN PROGRESS" written on them. Obey the general cautions, warnings, and instructions that follow when you install or work near the ice protection system: CAUTION: Be careful when you install the porous panels to make sure that you do no...
  • Page 12 SERVICE KIT SK208-179B CAUTION: Do not do damage to the ice protection system with solvents or paints. Most solvents and all paints can cause damage to the plastic membrane in the porous panels. Use only the materials from the list below when you work on or near the porous panels.
  • Page 13 SERVICE KIT SK208-179B CAUTION: Do not use the coupling nut to clench the olive to the fluid tubing. Use only specified clenching tools to do the clenching operation. Also, do not torque the couplings too much during the repair or replacement procedure. If the couplings leak, install new seals as necessary.
  • Page 14 SERVICE KIT SK208-179B CAUTION: As you accomplish this Service Kit, make sure that you keep a minimum edge distance of no less than two times the diameter of the rivet. (11) Install all rivets with a minimum edge distance of no less than two times the diameter of the rivet. Get access for the installation as follows: Do an initial weight and balance of the airplane before installation of the TKS Ice Protection System Installation and the SK208-180 or latest revision) or SK208-175B (or latest revision) as applicable...
  • Page 15 SERVICE KIT SK208-179B With U544055S Sealant, do a fay surface seal between the 0823337-2 Grommets and the structure. (Refer to the 208 Maintenance Manual, Chapter 20, Fuel, Weather, and High-Temperature Sealing - Maintenance Practices.) With 12 MS20470AD3-3A Rivets, attach the six 0823337-2 Grommets to the structure. (Refer to Figure 5, View A-A.) On the bottom of the airplane, install doublers for the support of the TKS tank as follows: From the right side of the airplane, remove the XPDR1 transponder antenna.
  • Page 16 SERVICE KIT SK208-179B Match drill the five nutplate holes and the 10 Number 40 (0.098-inch diameter) holes in the 2613495-1 TKS Left External Doubler. (m) Match drill the five nutplate holes and the 10 Number 40 (0.098-inch diameter) holes in the 2613495-2 TKS Right External Doubler.
  • Page 17 SERVICE KIT SK208-179B (Refer to Figure 5, View A-A and Detail A.) Put the 2613495-9 TKS Cutouts Doubler in position on the structure and make marks on the 2613495-9 TKS Cutouts Doubler for the 3.34-inch diameter hole, 1.75-inch diameter hole, and 52 rivet holes to attach the 2613495-9 TKS Cutouts Doubler to the structure.
  • Page 18 SERVICE KIT SK208-179B With the two S2906-4-2 Rivets, five MS20470AD4-4A Rivets, and one CM3827AD4-4A Rivet, install the 2613495-6 TKS Right Aft Doubler to the structure. With the 19 MS20470AD4-4A Rivets, install the 2613495-4 TKS Right Forward Doubler to the structure. (Refer to Figure 5, View D-D, Detail H, and Detail J.) Do the modification of the 2611127-22 Floorboard Assembly as follows: Remove the 2611058-22 Access Cover from the 2611127-22 Floorboard Assembly.
  • Page 19 SERVICE KIT SK208-179B Strap Angles and the structure and match drill to enlarge the three holes through each of the two 2613495-7 TKS Forward Strap Angles to 0.193-inch in diameter. (Refer to Figure 11, View D-D and View F-F.) Align the 2601548-3 Aft Left Strap Assembly and the 2601548-4 Aft Right Strap Assembly with the 2613495-8 TKS Aft Strap Angles and the structure and match drill to enlarge the four holes through each of the two 2613495-8 TKS Forward Strap Angles to 0.193-inch in diameter.
  • Page 20 SERVICE KIT SK208-179B With U470642 Sealant , fay seal the 2601552-1 TKS Tank Vent Weldment to the inside of the airplane and fay seal the 0823337-2 Grommet to the outside of the 2601552-10 Filler Port Doubler. With four MS20470AD3-4A Rivets, install the 2601552-1 TKS Tank Vent Weldment to the inside of the airplane and the 0823337-2 Grommet to the outside of the 2601552-10 Filler Port Doubler.
  • Page 21 SERVICE KIT SK208-179B Install the TKS tank as follows: (Refer to Figure 8) With 16 AN525-832R7 Screws and 16 NAS1149N832P Washers, install the tank to the nut-plates that you installed on the belly of the airplane. (Refer to Figure 14, View G-G and View H-H.) Install the 13146-05 LP Tank Wire Harness to the TKS tank.
  • Page 22 SERVICE KIT SK208-179B In the 0.44-inch diameter hole that you made in the airplane belly, install the MN6235 Bulkhead Short Connector and the MN6079 Backnut 1/8 BSP. (Refer to Figure 18, View A-A and View C-C.) Install the antenna doubler for the XPDR1 transponder antenna on the forward fairing as follows: Put the 9507001-3 Plate Assembly in the correct installation position.
  • Page 23 SERVICE KIT SK208-179B (Refer to Figure 17.) Install the 2601553-12 Aft Drain Tube Assembly on the equipment pallet. (Refer to Figure 14, View H-H.) Install the 13146-06 Low Profile Pallet Wire Harness on the equipment pallet. (Refer to Figure 14, View G-G), Attach the Windshield Pump EMI Shield to the equipment pallet with one MS21919WDG20 Clamp and one MS27039-1-07 Screw at the MS21075L3N Nutplate.
  • Page 24 SERVICE KIT SK208-179B With U470644 Sealant, fillet seal all around the flange edge of the 2613498-1 Forward Fairing Assembly where it is adjacent to the fuselage. Fay seal the 2601212-5 TKS Fairing Cover with U470644 Sealant. Install the 2601212-5 TKS Fairing Cover over the front fairing nose gear cutout with the five AN525-10R11 Screws.
  • Page 25 SERVICE KIT SK208-179B Remove and discard the 967B5 Drain Valve. Keep the nut and discard the o-ring. Install the 180C4 Valve Assembly with the new M83248/1-021 O-ring and NAS1149D1290K Washer and the kept 856A2 Nut. Install the washer under the nut. Use safety wire and the double-twist method to safety the 856A2 Nut.
  • Page 26 SERVICE KIT SK208-179B Make sure that there are no leaks and that fuel flows from the 2616033-8 208B Sump Tube Assembly when the drain valve is open. Make sure that there are no drips when the valve is closed. 13. (Refer to Figure 18.) Install the XPDR1 transponder antenna on the forward low profile TKS fairing as follows: Clean and electrically bond the antenna, and make sure that the maximum resistance value is no more than 0.5 ohms.
  • Page 27 SERVICE KIT SK208-179B • The windshield washer tube at the positions that follow: Leave the mounts attached and do not cut the tubing at this time. • At FS 166.148 attach the prop tube • At FS 176.19 attach the prop tube •...
  • Page 28 SERVICE KIT SK208-179B 16. Install the BLE Lens Assembly as follows: Remove and discard the lens retainer and the lens from the landing and taxi recognition lights on the left and the right wings. Keep the attachment hardware. (Refer to the Model 208 Maintenance Manual, Chapter 33, Landing and Taxi Recognition Light - Maintenance Manual.) Install the 2620028-1 Left BLE Lens Assembly and the 2620028-2 Right BLE Lens Assembly.
  • Page 29 SERVICE KIT SK208-179B CAUTION: When you fay seal the gurney flaps to the wing flaps, do one wing and then the other. The adhesive can cure quickly. With U000701S Sealant, fay seal the 2625027-1 Gurney Flaps to the left wing flap and the 2625027-1 Gurney Flaps to the right wing flap.
  • Page 30 SERVICE KIT SK208-179B Attach the TKS wire assembly to the S2034-1 Mount with one S2209 Tie. (Refer to Figure 14, View A-A.) Install the MS24524-23 BACKUP Switch (S1024) and the C15Green Tip on the 9910616-5 LED LAA Switch Plate Assembly. Install the MS24524-27 MAX FLOW Switch (S1023) and the C15Green Tip on the 9910616-5 LED LAA Switch Plate Assembly.
  • Page 31 SERVICE KIT SK208-179B (Refer to Figure 10, View D-D.) Install the 2605070-10 Icing Conditions Placard on the instrument panel as follows: Remove the installed icing conditions placard that is on the instrument panel. Clean the area where the new placard is to be installed with isopropyl alcohol. (Refer to the Maintenance Manual, Chapter 20, Solvents, Sealants and Adhesives - Maintenance Practices.) Install the 2605070-10 Icing Conditions Placard on the instrument panel in the position shown.
  • Page 32 SERVICE KIT SK208-179B Make sure that the tubing connections are attached correctly in all areas. Make sure that you check the tubing connections in the engine compartment. Make sure that the electrical connections are attached correctly. 27. Do a test of the wiring for the circuit breaker panel as follows: Disengage one circuit breaker.
  • Page 33 SERVICE KIT SK208-179B (19) Remove power from the system. (20) Remove the G1000 SD loader card from the PFD1 display. (21) Install the three G1000 SD database cards into their correct displays. (22) Apply power to the system and bring the three displays up in NORMAL mode. Do a check of the software configuration as follows: Put the EXTERNAL POWER switch to the BUS position.
  • Page 34 SERVICE KIT SK208-179B TABLE 1: TKS CIRCUIT BREAKERS W/S ANTI-ICE (HC016) BACKUP ANTI-ICE (HC015) ENG INTFC (HI013) Set initial conditions in accordance with Table 2. TABLE 2 INITIAL CONDITIONS Name Position Ground Power Supply 28, +0.5 VDC or −0.5 VDC External Power Battery (DC Power) Switch Fluid Control - Primary...
  • Page 35 SERVICE KIT SK208-179B (16) Put a five-gallon bucket below the TKS fluid tank and equipment pack drain line (under the low-profile fairing on the left side of the airplane). Do the fluid indication systems check as follows: Put the EXTERNAL POWER switch to the BUS position. Make sure that the fluid quantity readout on the MFD is green and reads “A-ICE GAL 0.0”.
  • Page 36 SERVICE KIT SK208-179B Do a check for the accuracy of the fluid quantity indication to make sure that it shows within 1.50 gallons of 11.7. Do the pump operation systems check as follows: CAUTION: During this check, if you see leakage of fluid at one or more connections in the system, turn the anti-ice system off, repair connections, and remove all leakage.
  • Page 37 SERVICE KIT SK208-179B (12) Disengage the BACKUP ANTI-ICE circuit breaker and make sure that the pump shuts off. (13) Put the FLUID CONTROL BACKUP switch to the OFF position. (14) Engage the BACKUP ANTI-ICE circuit breaker. (15) Put the FLUID CONTROL PRIMARY switch to the NORMAL position and start the timer. (16) Make sure that the two metering pumps are on for 20 seconds +3 seconds or −3 seconds and then off for 100 seconds +10 seconds or −10 seconds.
  • Page 38 SERVICE KIT SK208-179B (15) Make sure that the red A-ICE PRESS LOW annunciator comes on. (16) Disconnect the horizontal, low-pressure switch connector on the right side of the airplane. (17) Make sure that the red A-ICE PRESS LOW annunciator goes off. (18) Connect the horizontal, low-pressure switch connector on the left side of the airplane.
  • Page 39 SERVICE KIT SK208-179B TABLE 3: TKS PANEL / RELATED PROPORTIONING UNIT PORT Proportioning Unit Port TKS Panels 1, 5 Left Inboard Wing Panel Left Mid Wing Panel Left Outboard Wing Panel 3, 4 Left Wing Strut Panel 6, 7 Right Inboard Wing Panel 1, 5 Right Outboard Wing Panel 3, 4...
  • Page 40 SERVICE KIT SK208-179B TABLE 4: Panel Purge Flow Troubleshooting - Work Through Table as Necessary Until There Are Correct Flow Characteristics Is there enough fluid in the test cart? Add fluid to the test cart as necessary Are there correct flow characteristics for the Wipe leading edge with paper towel to even porous panel? If no, out the fluid flow...
  • Page 41 SERVICE KIT SK208-179B (16) Install new sealing rings (two S2800-942 Sealing Rings) and connect the two left inboard wing panel supply lines to ports 1 and 5 on the wing proportioning unit. (17) Disconnect the center TKS panel supply line from port 2 on the wing proportioning unit. (18) Connect the purge tank line to the left mid wing TKS panel as near to the panel as you can.
  • Page 42 SERVICE KIT SK208-179B (41) (Refer to Figure 13.) Continue the fluid purge until the panel is correctly purged in accordance with Figure 13 and Table 4. NOTE: To get an even flow over the panel it may be necessary to lightly run a dry cloth or paper towel over the leading edge and/or the dry spots of the panel during purging.
  • Page 43 SERVICE KIT SK208-179B (60) Stop the fluid supply. (61) Wait until the fluid pressure is released. (62) Slowly disconnect the test cart fluid supply tube from the inboard panel. (63) Install new sealing rings (two S2800-942 Sealing Rings) and connect the two right inboard wing panel supply lines to ports 1 and 5 on the wing proportioning unit.
  • Page 44 SERVICE KIT SK208-179B (86) Apply pressure of 20 psi to slowly start the fluid flow through the panel. (87) Wait until the fluid starts to come out all the holes at the same rate along the full length of the panel and increase the pressure to 70 psi.
  • Page 45 SERVICE KIT SK208-179B (107)Stop the fluid supply. (108)Wait until the fluid pressure is released. (109)Disconnect the purge tank lines. (110) Install a new S2800-942 Sealing Ring and connect the left horizontal stabilizer TKS supply line to the tailcone proportioning unit. (111) Disconnect the right horizontal stabilizer TKS panel supply line from the tailcone proportioning unit.
  • Page 46 SERVICE KIT SK208-179B TABLE 5 TKS Circuit Breaker Reference Designator PRIMARY ANTI-ICE (HC003) W/S ANTI-ICE (HC016) BACKUP ANTI-ICE (HC015) ENG INTFC (HI013) Make sure that conditions are in accordance with Table 6. TABLE 6 INITIAL CONDITIONS Name Position Ground Power Supply 28, +0.5 VDC or −0.5 VDC External Power Battery (DC Power) Switch...
  • Page 47 SERVICE KIT SK208-179B (17) To make sure that there is the same flow from one wing to the other, make sure that you collected 52 ounces +20 or −10 ounces, (1550 ml +600 ml or −300 ml) from each wing. The quantity of fluid collected from one side of the airplane should be within 20 ounces (600 ml) of the quantity collected from the other side of the airplane.
  • Page 48 SERVICE KIT SK208-179B Apply sealant to all of the access plates and panels on the bottoms of the wings, horizontal stabilizer, and vertical stabilizer, with U544055S Sealant and petrolatum parting agent. (Refer to the 208 Maintenance Manual, Chapter 6, Access Plates and Panels Identification - Description and Operation, and Chapter 20, Fuel, Weather, and High-Temperature Sealing - Maintenance Practices.) Install all of the wing inspection panels and access plates that you removed from the wings, horizontal stabilizer, and vertical stabilizer.
  • Page 49 SERVICE KIT SK208-179B Figure 1. TKS Installation (Sheet 1) SK208-179B February 7, 2013 Page 49...
  • Page 50 SERVICE KIT SK208-179B Figure 1. TKS Installation (Sheet 2) SK208-179B Page 50 February 7, 2013...
  • Page 51 SERVICE KIT SK208-179B Figure 1. TKS Installation (Sheet 3) SK208-179B February 7, 2013 Page 51...
  • Page 52 SERVICE KIT SK208-179B Figure 2. Wing Proportioning Unit Location (Sheet 1) SK208-179B Page 52 February 7, 2013...
  • Page 53 SERVICE KIT SK208-179B Figure 2. Wing Proportioning Unit Location (Sheet 2) SK208-179B February 7, 2013 Page 53...
  • Page 54 SERVICE KIT SK208-179B Figure 2. Wing Proportioning Unit Location (Sheet 3) SK208-179B Page 54 February 7, 2013...
  • Page 55 SERVICE KIT SK208-179B Figure 3. Fuselage Tubing Installation (Sheet 1) SK208-179B February 7, 2013 Page 55...
  • Page 56 SERVICE KIT SK208-179B Figure 3. Fuselage Tubing Installation (Sheet 2) SK208-179B Page 56 February 7, 2013...
  • Page 57 SERVICE KIT SK208-179B Figure 3. Fuselage Tubing Installation (Sheet 3) SK208-179B February 7, 2013 Page 57...
  • Page 58 SERVICE KIT SK208-179B Figure 3. Fuselage Tubing Installation (Sheet 4) SK208-179B Page 58 February 7, 2013...
  • Page 59 SERVICE KIT SK208-179B Figure 3. Fuselage Tubing Installation (Sheet 5) SK208-179B February 7, 2013 Page 59...
  • Page 60 SERVICE KIT SK208-179B Figure 3. Fuselage Tubing Installation (Sheet 6) SK208-179B Page 60 February 7, 2013...
  • Page 61 SERVICE KIT SK208-179B Figure 4. Fuselage Tubing Routing (Sheet 1) SK208-179B February 7, 2013 Page 61...
  • Page 62 SERVICE KIT SK208-179B Figure 4. Fuselage Tubing Routing (Sheet 2) SK208-179B Page 62 February 7, 2013...
  • Page 63 SERVICE KIT SK208-179B Figure 4. Fuselage Tubing Routing (Sheet 3) SK208-179B February 7, 2013 Page 63...
  • Page 64 SERVICE KIT SK208-179B Figure 4. Fuselage Tubing Routing (Sheet 4) SK208-179B Page 64 February 7, 2013...
  • Page 65 SERVICE KIT SK208-179B Figure 5. Fuselage Modification - TKS Fairing Tank (Sheet 1) SK208-179B February 7, 2013 Page 65...
  • Page 66 SERVICE KIT SK208-179B Figure 5. Fuselage Modification - TKS Fairing Tank (Sheet 2) SK208-179B Page 66 February 7, 2013...
  • Page 67 SERVICE KIT SK208-179B Figure 5. Fuselage Modification - TKS Fairing Tank (Sheet 3) SK208-179B February 7, 2013 Page 67...
  • Page 68 SERVICE KIT SK208-179B Figure 5. Fuselage Modification - TKS Fairing Tank (Sheet 4) SK208-179B Page 68 February 7, 2013...
  • Page 69 SERVICE KIT SK208-179B Figure 5. Fuselage Modification - TKS Fairing Tank (Sheet 5) SK208-179B February 7, 2013 Page 69...
  • Page 70 SERVICE KIT SK208-179B Figure 5. Fuselage Modification - TKS Fairing Tank (Sheet 6) SK208-179B Page 70 February 7, 2013...
  • Page 71 SERVICE KIT SK208-179B Figure 5. Fuselage Modification - TKS Fairing Tank (Sheet 7) SK208-179B February 7, 2013 Page 71...
  • Page 72 SERVICE KIT SK208-179B Figure 5. Fuselage Modification - TKS Fairing Tank (Sheet 8) SK208-179B Page 72 February 7, 2013...
  • Page 73 SERVICE KIT SK208-179B Figure 6. Tailcone Modification (Sheet 1) SK208-179B February 7, 2013 Page 73...
  • Page 74 SERVICE KIT SK208-179B Figure 6. Tailcone Modification (Sheet 2) SK208-179B Page 74 February 7, 2013...
  • Page 75 SERVICE KIT SK208-179B Figure 7. Correct Tubing Coupling Procedures (Sheet 1) SK208-179B February 7, 2013 Page 75...
  • Page 76 SERVICE KIT SK208-179B Figure 7. Correct Tubing Coupling Procedures (Sheet 2) SK208-179B Page 76 February 7, 2013...
  • Page 77 SERVICE KIT SK208-179B Figure 7. Correct Tubing Coupling Procedures (Sheet 3) SK208-179B February 7, 2013 Page 77...
  • Page 78 SERVICE KIT SK208-179B Figure 8. Low-Profile Tank Installation (Sheet 1) SK208-179B Page 78 February 7, 2013...
  • Page 79 SERVICE KIT SK208-179B Figure 8. Low-Profile Tank Installation (Sheet 2) SK208-179B February 7, 2013 Page 79...
  • Page 80 SERVICE KIT SK208-179B Figure 8. Low-Profile Tank Installation (Sheet 3) SK208-179B Page 80 February 7, 2013...
  • Page 81 SERVICE KIT SK208-179B Figure 8. Low-Profile Tank Installation (Sheet 4) SK208-179B February 7, 2013 Page 81...
  • Page 82 SERVICE KIT SK208-179B Figure 9. Tank Fairing Installation (Sheet 1) SK208-179B Page 82 February 7, 2013...
  • Page 83 SERVICE KIT SK208-179B Figure 10. Placards Installation (Sheet 1) SK208-179B February 7, 2013 Page 83...
  • Page 84 SERVICE KIT SK208-179B Figure 10. Placards Installation (Sheet 2) SK208-179B Page 84 February 7, 2013...
  • Page 85 SERVICE KIT SK208-179B Figure 10. Placards Installation (Sheet 3) SK208-179B February 7, 2013 Page 85...
  • Page 86 SERVICE KIT SK208-179B Figure 10. Placards Installation (Sheet 4) SK208-179B Page 86 February 7, 2013...
  • Page 87 SERVICE KIT SK208-179B Figure 11. Low Profile Tank Strap Installation (Sheet 1) SK208-179B February 7, 2013 Page 87...
  • Page 88 SERVICE KIT SK208-179B Figure 11. Low Profile Tank Strap Installation (Sheet 2) SK208-179B Page 88 February 7, 2013...
  • Page 89 SERVICE KIT SK208-179B Figure 11. Low Profile Tank Strap Installation (Sheet 3) SK208-179B February 7, 2013 Page 89...
  • Page 90 SERVICE KIT SK208-179B Figure 12. Wiring Modification (Sheet 1) SK208-179B Page 90 February 7, 2013...
  • Page 91 SERVICE KIT SK208-179B Figure 12. Wiring Modification (Sheet 2) SK208-179B February 7, 2013 Page 91...
  • Page 92 SERVICE KIT SK208-179B Figure 12. Wiring Modification (Sheet 3) SK208-179B Page 92 February 7, 2013...
  • Page 93 SERVICE KIT SK208-179B Figure 13. Fluid Flow During Purge Operation (Sheet 1) SK208-179B February 7, 2013 Page 93...
  • Page 94 SERVICE KIT SK208-179B Figure 13. Fluid Flow During Purge Operation (Sheet 2) SK208-179B Page 94 February 7, 2013...
  • Page 95 SERVICE KIT SK208-179B Figure 13. Fluid Flow During Purge Operation (Sheet 3) SK208-179B February 7, 2013 Page 95...
  • Page 96 SERVICE KIT SK208-179B Figure 14. Electrical Equipment Installation (Sheet 1) SK208-179B Page 96 February 7, 2013...
  • Page 97 SERVICE KIT SK208-179B Figure 14. Electrical Equipment Installation (Sheet 2) SK208-179B February 7, 2013 Page 97...
  • Page 98 SERVICE KIT SK208-179B Figure 14. Electrical Equipment Installation (Sheet 3) SK208-179B Page 98 February 7, 2013...
  • Page 99 SERVICE KIT SK208-179B Figure 14. Electrical Equipment Installation (Sheet 4) SK208-179B February 7, 2013 Page 99...
  • Page 100 SERVICE KIT SK208-179B Figure 14. Electrical Equipment Installation (Sheet 5) SK208-179B Page 100 February 7, 2013...
  • Page 101 SERVICE KIT SK208-179B Figure 14. Electrical Equipment Installation (Sheet 6) SK208-179B February 7, 2013 Page 101...
  • Page 102 SERVICE KIT SK208-179B Figure 15. Fuel Sump Installation (Sheet 1) SK208-179B Page 102 February 7, 2013...
  • Page 103 SERVICE KIT SK208-179B Figure 15. Fuel Sump Installation (Sheet 2) SK208-179B February 7, 2013 Page 103...
  • Page 104 SERVICE KIT SK208-179B Figure 15. Fuel Sump Installation (Sheet 3) SK208-179B Page 104 February 7, 2013...
  • Page 105 SERVICE KIT SK208-179B Figure 16. TKS Fairing Nutplate Installation (Sheet 1) SK208-179B February 7, 2013 Page 105...
  • Page 106 SERVICE KIT SK208-179B Figure 17. Equipment Pack Installation for the Low-Profile Tank (Sheet 1) SK208-179B Page 106 February 7, 2013...
  • Page 107 SERVICE KIT SK208-179B Figure 17. Equipment Pack Installation for the Low-Profile Tank (Sheet 2) SK208-179B February 7, 2013 Page 107...
  • Page 108 SERVICE KIT SK208-179B Figure 18. XPDR Antenna Installation (Sheet 1) SK208-179B Page 108 February 7, 2013...
  • Page 109 SERVICE KIT SK208-179B Figure 18. XPDR Antenna Installation (Sheet 2) SK208-179B February 7, 2013 Page 109...
  • Page 110 SERVICE KIT SK208-179B Figure 19. Vent Tube Installation (Sheet 1) SK208-179B Page 110 February 7, 2013...
  • Page 111 SERVICE KIT SK208-179B Figure 19. Vent Tube Installation (Sheet 2) SK208-179B February 7, 2013 Page 111...
  • Page 112 SERVICE KIT SK208-179B Figure 19. Vent Tube Installation (Sheet 3) SK208-179B Page 112 February 7, 2013...
  • Page 113 SERVICE KIT SK208-179B Figure 20. Filler Tube Installation (Sheet 1) SK208-179B February 7, 2013 Page 113...
  • Page 114 SERVICE KIT SK208-179B Figure 20. Filler Tube Installation (Sheet 2) SK208-179B Page 114 February 7, 2013...
  • Page 115 SERVICE KIT SK208-179B Figure 20. Filler Tube Installation (Sheet 3) SK208-179B February 7, 2013 Page 115...
  • Page 116 SERVICE KIT SK208-179B Figure 20. Filler Tube Installation (Sheet 4) SK208-179B Page 116 February 7, 2013...
  • Page 117 SERVICE KIT SK208-179B Figure 21. VG Installation (Sheet 1) SK208-179B February 7, 2013 Page 117...
  • Page 118 SERVICE KIT SK208-179B Figure 21. VG Installation (Sheet 2) SK208-179B Page 118 February 7, 2013...
  • Page 119 SERVICE KIT SK208-179B Figure 22. Gurney Flap Installation (Sheet 1) SK208-179B February 7, 2013 Page 119...

Table of Contents

Save PDF