Lutron Electronics Stanza SZ-2B Installation Instructions

Stanza
TM
Installation Instructions
Please Read Before Installing
SZ-2B SZ-3B SZ-4B
SZ-5B SZ-3/1B
Important Notes
Install in accordance with all local and
national electrical codes.
Environment: Ambient operating
temperature: 32 to 104 °F (0 to 40 °C),
0 to 90% humidity, non-condensing.
Indoor use only.
Spacing: If mounting one control above
another, leave at least 4.5 in (114 mm)
vertical space between them.
Faceplates: Use Lutron Stanza
faceplates for best color match and
aesthetic appearance. Do not paint
controls or faceplates.
Cleaning: To clean faceplate or buttons,
wipe with a clean damp cloth. DO NOT
use any chemical cleaning solutions.
Wallboxes: Lutron recommends using
3.5 in (89 mm) deep wallboxes for easier
installation.
RF Device Placement: RF keypads
must be located within 30 feet (9 m)
of an RF signal repeater or a device
configured as a repeater.
Stanza RF keypads cannot control
any device in the system until they are
addressed and programmed. When
powered and unaddressed, they turn
on their button backlights to indicate
proper operation.
Mounting Diagram
Locating post
Locating post
Control
Technical support: USA, Canada, Caribbean: 1.800.523.9466
Mexico: +1.888.235.2910
Central/South America: +1.610.282.6701
Warranty: 1-year limited warranty standard. 2-year parts and labor warranty, with
8-year pro-rated parts replacement on systems that include factory startup.
These products may be covered under one or more of the following U.S. patents: 5,838,226;
5,848,054; 5,905,442; 5,982,103; 6,687,487; 6,803,728; and corresponding foreign patents. U.S.
and foreign patents may be pending. Lutron and the sunburst logo are registered trademarks
and Stanza is a trademark of Lutron Electronics Co., Inc.
© 2009 Lutron Electronics Co., Inc.
Stanza Keypads
TM
SZ-2B, SZ-3B,
SZ-4B, SZ-5B,
SZ-3/1B
120 V 50 / 60 Hz 0.5 A
Installation
WARNING - Shock Hazard -
Wiring with power ON may result
in serious injury or death. Locate
and remove fuse or lock circuit
breaker in the OFF position
before proceeding.
1. Turn power OFF at fusebox or circuit
breaker.
2. Prepare wires. When making
wire connections, follow the
recommended strip lengths and
combinations for the supplied wire
connector.
Note: Wire connectors provided are
suitable for copper wire only.
Wire Connector:
• Strip insulation 3/8 in (9.5 mm) for
14 AWG (1.5 mm ) wire.
2
• Strip insulation 1/2 in (12.7 mm) for
16 or 18 AWG (1.0 or 0.75 mm
3. Wire controls as follows:
a. Connect the black control wire to
the Hot/Live wire coming from the
distribution panel.
b. Connect the white control wire to
the Neutral wire coming from the
distribution panel.
c. Twist wire connector tight.
Hot/ Black
Live
120 V
50 / 60 Hz
Neutral White
Control Faceplate adapter
mounting screws mounting screws
Locating hole
Faceplate/adapter
purchased separately.
Locating hole
English
FCC Information
Changes or modifications not expressly approved by Lutron Electronics Co. could void the user's authority to
operate this equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC rules. Operation is subject to the following: (1) This device may not cause harmful interfer-
ence, and (2) this device must accept any interference received, including interference that may cause undesired
operation.
Ensure your customer will
be happy by installing this
product correctly so the
buttons protrude from the
faceplate.
4. Push all wires back into the wallbox
and loosely fasten the control to the
wallbox using the control mounting
screws provided. Do not pinch the
wires.
• For installation with a recessed
wallbox, use spacer shims (Lutron
PN 257117) for proper support of
control(s).
• For multigang installation, verify
that the order of controls in the
wallbox corresponds to the faceplate
openings.
5. Attach Lutron Stanza faceplate
adapter and faceplate.
a. Align the locating posts on the
) wire.
2
control(s) to the holes in the
adapter.
b. Install the adapter onto front of
control(s) using the short screws
provided. The adapter should be
firmly against the controls.
c. Tighten control mounting screws
until faceplate adapter is flush to
wall (do not over-tighten).
d. Snap faceplate onto faceplate
adapter, and verify that control
is aligned properly and buttons
protrude in front of the faceplate.
e. If control(s) is (are) misaligned
or buttons are flush with the
faceplate, loosen control mounting
screws appropriately.
Correct: Incorrect:
Buttons protrude from Buttons are flush with
faceplate. faceplate. Loosen control
mounting screws.
6. Restore power. Check for correct
local operation (see Operation).
Keypad will not control a remote
device until it is addressed.
Troubleshooting Guide
Symptom
Keypad LEDs do not
light
Lights do not respond
to a button press
All status LEDs flash
when each keypad
button is pressed
Operation
Keypad Buttons
Buttons are backlit for easy location in
a darkened room.
FCC Information
Note: This equipment has been tested and found to
comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC rules. These limits are
designed to provide reasonable protection against
harmful interference in a residential and commercial
installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause
harmful interference to radio or television reception.
However, there is no guarantee that interference will
not occur in a particular installation. If this equipment
does cause harmful interference to radio or television
reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to
correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and
receiver.
• Connect the equipment into an outlet on a circuit
different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV
technician for help.
Cause and Action
Power not present
• Circuit breaker OFF or tripped. Perform short circuit check.
Wiring error
• Check wiring to be sure it matches installation instructions
and wiring diagrams.
Improper programming
• Check programming in the Stanza software.
Out of RF range
• Ensure device is within 30 feet (9 m) of another device
configured as a repeater.
Keypad is not addressed to the system
• Address device as part of a Stanza system.
Lutron Electronics Co., Inc.
Made and print ed in the U.S.A.
R P/N 030-1091 Rev. A 08/11/09
Status LEDs
Indicate current
scene selected;
all glow softly
as night lights
when scene is not
selected
If keypad is unpro-
grammed, all LEDs
flutter when any
button is pressed