Stihl TS 350 Manual
  1. Manuals
  2. Brands
  3. Stihl Manuals
  4. Saw
  5. TS 350
  6. Manual

Stihl TS 350 Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Advertisement

Table of Contents
loading

Related Manuals for Stihl TS 350

Summary of Contents for Stihl TS 350

  • Page 2: Table Of Contents

    &RQWHQWV Main Parts of the TS 350 Cutquik Starting This Manual contains operating and Definitions Checking Spark Plug safety instructions for your STIHL Safety precautions General Notes on Operation TS 350 Cutquik The operator Air filter Pay special attention to the safety...

  • Page 3: Main Parts Of The Ts 350 Cutquik

    Main Parts of the TS 350 Cutquik TS 350...

  • Page 4: Definitions

    'HILQLWLRQV  $EUDVLYH :KHHO  7KUXVW :DVKHU  7KURWWOH 7ULJJHU ,QWHUORFN Can either be an abrasive wheel Distributes claming pressure of Must be depressed before activating or a diamond abrasive wheel. mounting nut evenly over abrasive wheel. the throttle trigger.   :KHHO *XDUG  6WDUWHU *ULS  6WDUWLQJ 7KURWWOH /RFN...

  • Page 5: Safety Precautions

    7+( 23(5$725 Have your STIHL dealer show you note the following: how to operate your cut-off machine. 3K\VLFDO &RQGLWLRQ Observe all applicable local safety Most STIHL cut-off machine models regulations, standards and ordinances.
  • Page 6 To reduce the risk of burn injury STIHL Wear an approved safety hard hat to suppression when wet cutting is feasible.
  • Page 7 :DUQLQJ 2 and 3. :DUQLQJ Unauthorized wheels may shatter or Cutting masonry, concrete and other break. Use only STIHL wheels or other :DUQLQJ materials with silica in their composition authorized wheels with approved RPM may give off dust containing crystalline Never modify a cut-off machine in any ratings.
  • Page 8 Always stop the engine before putting a centered and diamond particles are Your STIHL dealer stocks a range of cut-off machine down or carrying it. The imbedded in their cutting edges. special abrasive wheels for the many abrasive wheel continues to rotate for a applications of the cut-off machine.
  • Page 9 IRU 76  DQG 76  RQO\ or property damage. Use extreme cau- tion when handling gasoline or fuel mix. The STIHL TS 350 and TS 360 For assembly, follow the procedure Do not smoke or bring any fire or flame...
  • Page 10 Do not drop start. This method is very much force as possible. as the combustible dangerous because you may loose The screw driver end of the STIHL engine is running. These control of the cut-off machine. combination wrench or other similar tool gases (e.g.
  • Page 11 :DUQLQJ Never use the cut-off machine with one Avoid standing in direct line with the hand. Your STIHL cut-off machine is wheel. Sparks from cutting metal designed for hand-held use or operation can burn or cause cloth- on a cut-off machine cart. Cutting with ing to catch fire.
  • Page 12 Always use the cart to cut in a straight Hold the cut-off machine steady. Do not line. Have your STIHL dealer check your change the direction of the cut during cut-off machine and make proper the cut as this may produce a high adjustments or repairs.
  • Page 13 Severe personal injury or death can Begin abrasive and continue at full result. throttle. Use only cutting attachment authorized by STIHL. 1HYHU use chipped abrasive Do not overreach.

  • Page 14: Of The Cut-Off Machine

    16. Release the pressure on the Use only STIHL replacement parts for cut-off machine as you reach the maintenance and repair. Use of parts end of the cut. Too much pressure...

  • Page 15: Storing The Machine

    Store cut-off machine in a or locked location - out of the STIHL. Always press spark plug boot high or locked place, away from children. reach of children and other snugly onto spark plug terminal of the unauthorized persons.

  • Page 16: Mounting The Arbor Bearing And Guard

    V-belt is new, this operation is easier if the M 10 hex. head nut (8) is turned counterclockwise with the combination wrench (17 mm), i.e. this turns the belt pulley (2). Position bearing plate (3) so that the tapped holes line up with the slots in the arm. TS 350...

  • Page 17: Tensioning The V-Belt

    360° adjustment since the advisable to check V-belt tension after about 1 operating movement of the adjusting lever is restricted by the hour and correct it if necessary. handlebar mounting, i. e. reduced by about 20°. TS 350...

  • Page 18: Abrasive Wheels

    Cutting wheels for free-hand cutting operations are sub- jected to particularly high bending and compressive stres- ses. STIHL has therefore developed - together with lead- ing abrasive wheel manufacturers - top quality cutting blades which exactly match the engine characteristics of the cut-off-saw.

  • Page 19: Mounting The Abrasive Wheel

    In such a case it is essential to ensure that the segments of both wheels are positioned exactly next to one another. Important! Two composite wheels must never be used simultaneously, for they may break and cause injuries as they wear down unevenly. TS 350...

  • Page 20: Fuel Mix

    Before storing your machine for a long US gal. US fl.oz period, drain and clean the fuel tank and Use only STIHL two-stroke engine oil or run engine until carburetor is dry. equivalent branded two-stroke air- 2 1/2 cooled engine oils with the classification 12.8...

  • Page 21: Starting

    6. As soon as the engine is running, disengage starting throttle lock (5) immediately by briefly squeezing the throttle trigger so that the engine can settle down to idle speed. 7. The engine is stopped by moving the stop switch (2) to the "STOP" position. TS 350...
  • Page 22 A new engine or one which has been run until the fuel tank is dry will not start first time after fueling because fuel only begins to reach the carburetor when the engine has been turned over few times on the starter TS 350...

  • Page 23: Checking Spark Plug

    Use only resistor type spark plugs immediately, but let run for a short while STIHL (see “Specifications”). Always of the approved range. at idling speed. This allows the heat press spark plug boot  snugly onto...

  • Page 24: Air Filter

    (3). Pull the prefilter (4) off the main filter (5). If necessary, also remove the auxiliary filter (6), knock it out on the palm of your hand and wash it in a non-flammable cleaning solution (warm soapy water). TS 350...

  • Page 25: Adjusting Carburetor

    $GMXVWLQJ &DUEXUHWRU 0RWRU PDQDJHPHQW 6HWWLQJ LGOLQJ VSHHG Exhaust emissions are controlled by the It is usually necessary to change the design of the fundamental engine setting of the idle speed adjusting screw /$ after every correction to the low parameters and components speed adjusting screw / .

  • Page 26: Rewind Starter

    (6). Pull the rope through the rotor and secure it with a simple overhand knot. Slide rotor onto the starter post and turn it back and forth until the rewind spring's anchor loop (7) engages. TS 350...
  • Page 27 A rewind spring that is tensioned too heavily will in its housing starting from outside to inside in probably break. counterclockwise direction. Reassemble the rope rotor as Re-install the fan shroud with the three retaining screws above. securely tightened. TS 350...

  • Page 28: Changing The V-Belt

    Check the position and freedom of move- ment of the V-belt before finally tightening the mounting screws. Refit the arbor bearing and abrasive wheel guard - refer to "Assembling the Arbor Bearing and Guard" and "Tensioning the V-belt". TS 350...

  • Page 29: Stihl Cutquik Tm Cart

    Unscrew the screw (1) • Remove the spark arresting screen (2) with suitable pliers. The TS 350 can be mounted on a cart which greatly • Clean the soiled spark arresting simplifies handling of the machine and enables smooth, screen, do not widen the mush straight cuts to be obtained for road repairs and applying •...

  • Page 30: Maintenance Chart

    (Bottom side of unit) Replace :DUUDQW\ FODLPV IROORZLQJ UHSDLUV The user of this unit should carry out Original STIHL parts can be identified FDQ EH DFFHSWHG RQO\ LI WKH UHSDLU only the maintenance operations by the STlHL part number, the...

  • Page 31: Specifications

    Diamond abrasive wheels for stone (breakerless) magneto ignition and asphalt. STIHL Cutquik cart Spark plug Attachment (TS 350) for Cutquik cart (interference- Dia. 300 mm (12 in) or 350 mm (14 in) Cutting depth limiter suppressed): Bosch WSR 6 F 2.6 to 6 mm (0.10 to 0.24 in) thick...
  • Page 32 STIHL service center as soon as a meet the U.S. EPA regulations for small the part will be repaired or replaced by problem exists.
  • Page 33 Any such work shall be free of Deviations from this recommendation warranty card to STIHL. If any emission charge to the owner if it is determined regarding quality and mixing ratio of fuel related part on your engine is defective, that a warranted part is defective.

Table of Contents