Perenio PECWS01 Installation And Operation Manual
Door & window sensor
Hide thumbs
Also See for PECWS01:
- Installation and operation manual (31 pages) ,
- Quick start manual (29 pages) ,
- Quick start manual (8 pages)
Related Manuals for Perenio PECWS01
Summary of Contents for Perenio PECWS01
- Page 1 Installation and Operation Manual for Perenio® PECWS01 Door & Window Sensor July, 2021...
-
Page 3: Introduction
Copyright of ©Perenio IoT spol s r.o. All rights reserved. The Perenio® trademark is owned by Perenio IoT spol s r.o. (hereinafter referred to as the Perenio IoT). All other similar trademarks and names, as well as logos and other symbols are the property of their respective owners*. -
Page 4: Responsibility And Technical Support
Perenio IoT reserves the right to modify the device and make corrections or changes to this document without prior notice of the User, and shall not be responsible for any... -
Page 5: Conformance To Standards
To protect the environment and human health, please dispose of used electrical and electronic equipment according to approved safe disposal guidelines ©Perenio IoT spol s r.o. All rights reserved Doc Version: 2.4.1 Page 5 of 38... - Page 6 Details on available Certificates are specified in Section 6 of the present document. For copies of Certificates and Reports, please visit a corresponding Section at perenio.com. Doc Version: 2.4.1 ©Perenio IoT spol s r.o. All rights reserved Page 6 of 38...
-
Page 7: Table Of Contents
1.3 Scope of Delivery..................12 1.4 Packaging and Labelling ................13 1.5 Safe Operation Rules ................13 1.6 Standalone Operation of Perenio® Sensors ..........14 2 Installation and Setup................... 15 2.1 First Installation and Configuration ............16 2.2 Sensor Control Panel ................21 2.2.1 Armed Mode .................. - Page 8 A. SWITCHING ON AND INSTALLATION OF THE DOOR & WINDOW SENSOR ..16 B. LOGIN TO THE EXISTING USER ACCOUNT ............18 C. CONNECTION TO THE CONTROL GATEWAY/IOT ROUTER ......... 19 Doc Version: 2.4.1 ©Perenio IoT spol s r.o. All rights reserved Page 8 of 38...
-
Page 9: General Description And Specifications
Installation and Operation Manual for Perenio® PECWS01 Door & Window Sensor 1 General Description and Specifications 1.1 General Purpose The PECWS01 magnetic sensor is a device that sends corresponding signals to the Perenio® Control Gateway/IoT Router when the magnet is moved away from the main part of the device to a distance of more than 20-30 mm or is returned back to initial state. -
Page 10: Figure 2 - Door & Window Sensor Components
Reset was successful, the sensor was deleted from the mobile app The sensor is on, activated in the mobile app, and is in the working order Sensor is off Doc Version: 2.4.1 ©Perenio IoT spol s r.o. All rights reserved Page 10 of 38... -
Page 11: Technical Specification
(Actuation distance) Reset Button Side panel of the Sensor Standalone Operation Power Type CR2032 Battery (125mAh, 3V), 1pc. Power Consumption Standby Mode: not more than 0.0016mA ©Perenio IoT spol s r.o. All rights reserved Doc Version: 2.4.1 Page 11 of 38... -
Page 12: Scope Of Delivery
Certification CE, EAC, RoHS, UA.TR 1.3 Scope of Delivery The following items and accessories are supplied within the Perenio® PECWS01 Door & Window Sensor package: 1. PECWS01 Door & Window Sensor with a magnet (1 set) 2. Battery (CR2032) (1 pc.) 3. -
Page 13: Packaging And Labelling
* Images of accessories are provided for informational purposes only 1.4 Packaging and Labelling The Perenio® PECWS01 Door & Window Sensor is supplied in an individual blister package of 171mm x 126mm x 27mm (L x W x H) containing the full name and... -
Page 14: Standalone Operation Of Perenio® Sensors
Therefore, its operation is arranged by sending notifications to the smartphone. However, to run active scenarios, the User must have an installed Perenio Smart Building Management System Mobile App and an activated Control... -
Page 15: Installation And Setup
2. Attach the 3M tape to the Sensor surface. 3. Make sure that the place of installation is smooth and free from dust, dirt, etc. ©Perenio IoT spol s r.o. All rights reserved Doc Version: 2.4.1 Page 15 of 38... -
Page 16: First Installation And Configuration
SWITCHING ON AND INSTALLATION OF THE DOOR & WINDOW SENSOR To install the Perenio® PECWS01 Door & Window Sensor, follow steps below: 1. Unpack the device. 2. Choose a suitable installation area for the Sensor and the Magnet (window frame, door leaf, etc.) as follows:... -
Page 17: Figure 5 - Installation Rules For The Sensor And The Magnet
NOTE. The Sensor and the Magnet shall be mounted coaxially so that in the closed position of the door or the window the Magnet is at a distance of no more than 2cm from the Sensor. ©Perenio IoT spol s r.o. All rights reserved Doc Version: 2.4.1 Page 17 of 38... - Page 18 To restore a forgotten password, use the e-mail address linked to your User Account, to which instructions on changing the password will be sent. Doc Version: 2.4.1 ©Perenio IoT spol s r.o. All rights reserved Page 18 of 38...
- Page 19 (You should remove the sensor battery and insert it back into the casing). NOTE. To eliminate connection failures, follow instructions specified on corresponding screens of the smartphone. ©Perenio IoT spol s r.o. All rights reserved Doc Version: 2.4.1 Page 19 of 38...
-
Page 20: Figure 6 - Add New Device (Sensor) Procedure
PECWS01 Door & Window Sensor The entire process of the Sensor connection in the Mobile App is shown below. – Add new device (Sensor) procedure Figure 6 Doc Version: 2.4.1 ©Perenio IoT spol s r.o. All rights reserved Page 20 of 38... -
Page 21: Sensor Control Panel
The Armed Mode can be activated and deactivated in two ways as follows: Press the corresponding toggle switch in the sensor control panel; NOTE that in this case, the specified sensor will be Armed only. ©Perenio IoT spol s r.o. All rights reserved Doc Version: 2.4.1 Page 21 of 38... -
Page 22: Battery Level
2.2.3 Event History In this tab, the user can view the status of the sensor, as well as the time when the event occurred. Doc Version: 2.4.1 ©Perenio IoT spol s r.o. All rights reserved Page 22 of 38... -
Page 23: Device Scenarios
The user may use the Door & Window Sensor in preset scenarios in order to automate the operation of Perenio® devices for a specific purpose (e.g., to turn on the night lamp in a room upon motion detection in another room). - Page 24 “Next” button. 4. Select a device that shall perform the desired action upon actuation of at least one of the sensors selected in the previous step. Doc Version: 2.4.1 ©Perenio IoT spol s r.o. All rights reserved Page 24 of 38...
- Page 25 5. Enter the scenario name and click on the “Save” button. 6. Run the created scenario by clicking on a corresponding button in the “Scenarios” tab. ©Perenio IoT spol s r.o. All rights reserved Doc Version: 2.4.1 Page 25 of 38...
-
Page 26: Additional Settings
NOTE that deleted scenario cannot be recovered, so if you accidentally delete it, you will have to create it again. 2.2.5 Additional Settings After the Sensor is activated in the Perenio Smart app, the user can make the following settings remotely: ... - Page 27 ATTENTION! The alarm delay can only be set for sensors that are Armed. This feature allows users to Disarm devices after entering the premises without receiving false alarms. ©Perenio IoT spol s r.o. All rights reserved Doc Version: 2.4.1 Page 27 of 38...
-
Page 28: Changing The Room Or Location For The Sensor
CG/IoT Router is required) as follows: a. Sign in to the Perenio Smart app and select the Location where the Sensor is activated; b. In the Devices tab, select the required Sensor from the list and click on icon (Settings);... -
Page 29: History And Push-Notifications
Installation and Operation Manual for Perenio® PECWS01 Door & Window Sensor 2.4 History and Push-Notifications All notifications and other messages including changes in the status of Perenio® devices are displayed in the “History” tab. The most important messages can be viewed online in the “... -
Page 30: Battery Replacement
(See below). – Positioning of the battery in the Door & Window Sensor Figure 7 After battery replacement, the LED of the Sensor will blink. Doc Version: 2.4.1 ©Perenio IoT spol s r.o. All rights reserved Page 30 of 38... -
Page 31: Maintenance And Repair
Repair mechanical damages to devices (in Service Centers). The Perenio® Door & Window Sensor repairs shall be carried out in Service Centers, because casings will have to be opened in the case of any element failure. In the case of warranty repairs or replacement, the User shall provide the Seller with the sales receipt and the purchased device. -
Page 32: Warranty Obligations
The Manufacturer shall guarantee that all materials, components and assemblies of Perenio® devices are free from defects under normal operation within the warranty period. The limited warranty shall be applied to the first End Customer of Perenio® devices only and cannot be transferred to a subsequent customer. - Page 33 Installation and Operation Manual for Perenio® PECWS01 Door & Window Sensor LIMITATION OF LIABILITY Perenio® devices SHALL NOT BE SUBJECT TO a free warranty service in the case of identification of at least one of the following damages or defects: ...
- Page 34 Doc Version: 2.4.1 ©Perenio IoT spol s r.o. All rights reserved Page 34 of 38...
-
Page 35: Storage, Transportation And Disposal Of Devices
PECWS01 Door & Window Sensor 5 Storage, Transportation and Disposal of Devices The Perenio® Door & Window Sensor may be shipped by any kind of covered vehicles (by rail, or road or in sealed heated airplane compartments, etc.) in accordance with the requirements of current regulatory documents applicable to fragile goods sensitive to moisture. -
Page 36: Other Information
Declarations, Reports 19, 2018; Test Verification of Conformity #GFT-OP-11b as of March 7, 2017 Addresses of Service Centers are available at perenio.com in the “Support” Section. Doc Version: 2.4.1 ©Perenio IoT spol s r.o. All rights reserved Page 36 of 38... -
Page 37: Troubleshooting
Damage of the Sensor Call the service center or the Magnet The sensor does not Low battery level Change the battery activate ©Perenio IoT spol s r.o. All rights reserved Doc Version: 2.4.1 Page 37 of 38... -
Page 38: Glossary
General term which means a building or a structure in which Perenio® Cameras, Control Gateways/IoT Routers and/or Sensors are installed Perenio Smart Software developed by Perenio IoT for remote control of wireless Cameras from smartphones Viewing Angle The area that falls into the field of viewing of the Sensor...