Perenio PECLS01 Installation And Operation Manual
Leak sensor
Hide thumbs
Also See for PECLS01:
- Installation and operation manual (28 pages) ,
- Quick start manual (25 pages) ,
- Manual (8 pages)
Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Perenio PECLS01
Summary of Contents for Perenio PECLS01
- Page 1 Installation and Operation Manual for Perenio® PECLS01 Leak Sensor July, 2021...
-
Page 3: Introduction
Copyright of ©Perenio IoT spol s r.o. All rights reserved. The Perenio® trademark is owned by Perenio IoT spol s r.o. (hereinafter referred to as the Perenio IoT). All other similar trademarks and names, as well as logos and other symbols are the property of their respective owners*. -
Page 4: Responsibility And Technical Support
Perenio IoT reserves the right to modify the device and make corrections or changes to this document without prior notice of the User, and shall not be responsible for any... -
Page 5: Conformance To Standards
To protect the environment and human health, please dispose of used electrical and electronic equipment according to approved safe disposal guidelines ©Perenio IoT spol s r.o. All Rights Reserved Doc Version: 2.5.1 Page 5 of 32... - Page 6 Details on available Certificates are specified in Section 6 of the present document. For copies of Certificates and Reports, please visit a corresponding Section at perenio.com. Doc Version: 2.5.1 ©Perenio IoT spol s r.o. All Rights Reserved Page 6 of 32...
-
Page 7: Table Of Contents
1.3 Scope of Delivery..................12 1.4 Packaging and Labelling ................13 1.5 Safe Operation Rules ................13 1.6 Standalone Operation of Perenio® Sensors ..........14 2 Installation and Setup................... 15 2.1 First Installation and Configuration ............15 2.2 Sensor Control Panel ................19 2.2.1 Battery Level .................. - Page 8 A. SWITCHING ON AND INSTALLATION OF THE LEAK SENSOR ......16 B. LOGIN TO THE EXISTING USER ACCOUNT ............16 C. CONNECTION TO THE CONTROL GATEWAY/IOT ROUTER ......... 17 Doc Version: 2.5.1 ©Perenio IoT spol s r.o. All Rights Reserved Page 8 of 32...
-
Page 9: General Description And Specifications
1 General Description and Specifications 1.1 General Purpose The Perenio® PECLS01 Leak Sensor is a device intended to alert users in the case of flood in the room. This device is used as part of the Perenio Smart Building Management System and is suitable for detection of leakage of water and some other liquids in the place of its installation. -
Page 10: Figure 2 - Buttons And Indicators
Reset was successful, the sensor was deleted from the mobile app The sensor is on, activated in the mobile app, and is in the working order Sensor is off Doc Version: 2.5.1 ©Perenio IoT spol s r.o. All Rights Reserved Page 10 of 32... -
Page 11: Technical Specification
Standalone Operation Available Power Type CR123A Battery (1300mAh, 3V), 1 pc. Power Consumption Standby Mode: not more than 0.2mA Alarm Mode: not more than 40mA ©Perenio IoT spol s r.o. All Rights Reserved Doc Version: 2.5.1 Page 11 of 32... -
Page 12: Scope Of Delivery
24 months Certification CE, EAC, RoHS, UA.TR 1.3 Scope of Delivery The following items and accessories are supplied within the Perenio® PECLS01 Leak Sensor package: 1. PECLS01 Leak Sensor (1 pc.) 2. Battery (CR123A) (1 pc.) 3. Quick Start Guide (1 pc.) 4. -
Page 13: Packaging And Labelling
* Images of accessories are provided for informational purposes only 1.4 Packaging and Labelling The Perenio® PECLS01 Leak Sensor is supplied in an individual blister package of 171mm x 126mm x 27mm (L x W x H) containing the full name and marking of the device, the list of accessories provided and basic technical specifications thereof, as well as the date of manufacture and information about the Manufacturer of devices. -
Page 14: Standalone Operation Of Perenio® Sensors
1.6 Standalone Operation of Perenio® Sensors The Control Gateway/IoT Router in not necessarily required for all Perenio® Sensors in order to alert Users on potentially dangerous situations. So, the Leak Sensor can operate as a standalone device, i.e. when it detects leakage in a room, it starts beeping. -
Page 15: Installation And Setup
Perenio Smart Mobile App, it is necessary to perform the following steps: 1. Unpack the Sensor and switch it on (See par. A below). 2. Login in to the Perenio Smart Building Management System User Account (See par. B below). - Page 16 5. Install the Sensor in the selected room. SWITCHING ON AND INSTALLATION OF THE LEAK SENSOR To install the Perenio® PECLS01 Leak Sensor, follow steps below: 1. Unpack the device. 2. Select suitable installation area near a potential source of flood (water valve, washing machine, radiators, etc.).
- Page 17 (You should remove the sensor battery and insert it back into the casing). NOTE. eliminate connection failures, follow instructions specified on corresponding screens of the smartphone. ©Perenio IoT spol s r.o. All Rights Reserved Doc Version: 2.5.1 Page 17 of 32...
-
Page 18: Figure 5 - Add New Device (Sensor) Procedure
PECLS01 Leak Sensor The entire process of the Sensor connection in the Mobile App is shown below. – Add new device (Sensor) procedure Figure 5 Doc Version: 2.5.1 ©Perenio IoT spol s r.o. All Rights Reserved Page 18 of 32... -
Page 19: Sensor Control Panel
2.2.2 Event History In this tab, the user can view the status of the sensor, as well as the time when the event occurred. ©Perenio IoT spol s r.o. All Rights Reserved Doc Version: 2.5.1 Page 19 of 32... -
Page 20: Additional Settings
Subscription Plan (It is 7 days for free Subscription). 2.2.3 Additional Settings After the Sensor is activated in the Perenio Smart app, the user can make the following settings remotely: Change or upload the device image for easier identification of the sensor in the list of connected devices;... -
Page 21: Leak Sensor Tightness
Close the Sensor casing according to special marks until a click appears (See Figure below). ©Perenio IoT spol s r.o. All Rights Reserved Doc Version: 2.5.1 Page 21 of 32... -
Page 22: Changing The Room Or Location For The Sensor
CG/IoT Router is required) as follows: a. Sign in to the Perenio Smart app and select the Location where the Sensor is activated; b. In the Devices tab, select the required Sensor from the list and click on icon (Settings);... -
Page 23: History And Push-Notifications
If the sensor is disconnected, it will disappear from the list of connected devices. 2.5 History and Push-Notifications All notifications and other messages including changes in the status of Perenio® devices are displayed in the “History” tab. The most important messages can be viewed online in the “... -
Page 24: Battery Replacement
Control Gateway firmware update, as well as notifications about low battery level of the sensor and changing the armed mode for the Location. Typical Events. Various Perenio IoT newsletters, as well as messages about triggering Door & Window/Motion sensor in the disarmed mode. -
Page 25: Maintenance And Repair
Repair mechanical damages to devices (in Service Centers). The Perenio® PECLS01 Leak Sensor repairs shall be carried out in Service Centers, because casings will have to be opened in the case of any element failure. In the case of warranty repairs or replacement, the User shall provide the Seller with the sales receipt and the purchased device. -
Page 26: Warranty Obligations
The Manufacturer shall guarantee that all materials, components and assemblies of Perenio® devices are free from defects under normal operation within the warranty period. The limited warranty shall be applied to the first End Customer of Perenio® devices only and cannot be transferred to a subsequent customer. - Page 27 Perenio® PECLS01 Leak Sensor LIMITATION OF LIABILITY Perenio® devices SHALL NOT BE SUBJECT TO a free warranty service in the case of identification of at least one of the following damages or defects: Any damage caused by force majeure, accidents, and willful or careless acts (omissions) of the Customer or third parties;...
- Page 28 Doc Version: 2.5.1 ©Perenio IoT spol s r.o. All Rights Reserved Page 28 of 32...
-
Page 29: Storage, Transportation And Disposal Of Devices
PECLS01 Leak Sensor 5 Storage, Transportation and Disposal of Devices The Perenio® Leak Sensor may be shipped by any kind of covered vehicles (by rail, or road or in sealed heated airplane compartments, etc.) in accordance with the requirements of current regulatory documents applicable to fragile goods sensitive to moisture. -
Page 30: Other Information
Radio Test Report #STS183222W01 as of March 31, 2018; Radio Test Report #STS183222W02 as of March 31, 2018. Addresses of Service Centers are available at perenio.com in the “Support” Section. Doc Version: 2.5.1 ©Perenio IoT spol s r.o. All Rights Reserved... -
Page 31: Troubleshooting
“offline” the sensor, or it is out reduce the distance unexpectedly of the Zigbee between the Sensor and the coverage Control Gateway/IoT Router ©Perenio IoT spol s r.o. All Rights Reserved Doc Version: 2.5.1 Page 31 of 32... -
Page 32: Glossary
General term which means a building or a structure in which Perenio® Cameras, Control Gateways and/or Sensors are installed Perenio Smart Software developed by Perenio IoT for remote control of wireless Cameras from smartphones Zigbee A network protocol designed for secure transmission of data...