Download
Share
Print this page
Quooker PRO3 Installation Manual
  1. Manuals
  2. Brands
  3. Quooker Manuals
  4. Plumbing Product
  5. PRO3
  6. Installation manual

Quooker PRO3 Installation Manual

Hide thumbs Also See for PRO3:

Advertisement

Quick Links

Download this manual
Installation guide PRO3
Before installing read this guide first

Advertisement

loading

Related Manuals for Quooker PRO3

Summary of Contents for Quooker PRO3

  • Page 1 Installation guide PRO3 Before installing read this guide first...
  • Page 2 13 amp socket, water supply and waste pipe. The Quooker tank must be fitted in an upright position. If the tank is to be fitted in a cabinet with drawers, an optional bracket can be purchased to suspend the tank from the cabinet wall.
  • Page 3 The fastest way to do this is as follows: turn off the Quooker, but leave the plug in the socket. Then open the boiling-water tap and turn it off once the water runs cold. You can find a more detailed explanation for disconnecting the tank in chapter F.

  • Page 4: Declaration Of Conformity

    Declaration of conformity Quooker Nederland b.v., Staalstraat 13, 2984 AJ Ridderkerk (The Netherlands) herewith declares, on our own responsibility, that the product Quooker PRO3 is in accordance with the conditions of the following directives: 2014/35/EU Low Voltage Directive (LVD) 2011/65/EU Restriction of Hazardous Substances (RoHS) Directive...

  • Page 5: Technical Specifications

    Technical specifications Tank PRO3 Voltage 230 V Wattage 1600 W Capacity 3 litres Heating-up time* 10 minutes Standby power consumption 10 W Tank height 46 cm Required working height 52 cm Tank diameter 15 cm Min. mains pressure 200 kPa (2 bar) Max.
  • Page 6 Contents of the pack 1. - Nordic single tap, packing ring, centring ring, steel ring, brass sink nut and two screws - or Fusion tap, packing ring, brass fixing plate, fixing nut, white tap support (for thin work tops) and two inlet hose screens - or Flex tap, hoses, fibre washer(s), steel washer, screw ring with two screws, coupling with boiling water hose, white tap support, two inlet hose screens and quick-release tool.
  • Page 7 2. PRO3 tank 3. Quooker inlet valve with packing ring 4. Angle stopcock with filter and packing ring 5. Inlet couplings and packing rings...
  • Page 8 Overview of Nordic single tap installation It is recommended that you install the Quooker in the following order: A. Drilling hole B1. Fitting Nordic single tap C. Connecting water D. Connecting waste E. Connecting tank Note: Bear in mind that the tank, inlet valve and socket must remain easily accessible for servicing.
  • Page 9 Overview of Fusion tap installation It is recommended that you install the Quooker in the following order: A. Drilling hole B2. Fitting Fusion tap C. Connecting water D. Connecting waste E. Connecting tank Note: Bear in mind that the tank, inlet valve and socket must remain easily accessible for servicing.
  • Page 10 Overview of Flex tap installation It is recommended that you install the Quooker in the following order: A. Drilling hole B3. Fitting Flex tap C. Connecting water D. Connecting waste E. Connecting tank Note: Bear in mind that the tank, inlet valve and socket must remain easily accessible for servicing.
  • Page 11 Drilling hole • Note: The tap hole for the Nordic single tap should be 32 mm in diameter. The Fusion and Flex tap hole should be 35 mm in diameter. • The Nordic single tap should ideally be positioned at the corner of the sink to enable use above the sink or the work top.
  • Page 12 Fitting Nordic single tap • The total length of the hose between the boiling-water tap and tank is only 70 cm. The tank must therefore be fitted close to the tap. Extension hoses are available in different lengths but are not normally required. •...
  • Page 13 Screw the fixing nut onto the tap thread. Adjust the position of the tap to ensure that the Quooker logo is facing the user. When the handle is in the cold position, it will be parallel to the edge of the work top.
  • Page 14 Fitting Flex tap • When installing the reservoir it is necessary to take into account that the Flex tap coupling must be able to move up and down freely. 1. Fit hoses Fit the hot, cold and mixer water hose to the tap.
  • Page 15 5. Attach the coupling Click the pull-out hose into the coupling’s quick-release fitting while ensuring that the hose pillar is fully inserted. 6. Fit the mixer water hose Click the mixer water hose into the coupling’s quick-release fitting while ensuring that the hose pillar is fully inserted.

  • Page 16: Connecting Water

    Connecting water • The Quooker operates under mains water pressure and must always be fitted to the water pipe with the supplied inlet valve. • The Nordic single tap, the Fusion tap or the Flex tap must be installed according to the locally applicable regulations.
  • Page 17 Connecting tank to tap • The Quooker tank is supplied with a UK 3 pin plug and requires a standard 13 amp earthed socket. • If the mains lead is damaged, it must be replaced by the manufacturer, their agent or a qualified technician.
  • Page 18 3. Isolating Close the main shut-off valve or the angle stopcock for cold water. Check that the Quooker is depressurized by opening the Nordic single tap or the boiling-water On/off handle of the Fusion or Flex tap again. If it is depressurized, no water should flow out of it.
  • Page 20 Quooker Hong Kong Ltd. 10/F, YF Life Tower 33 Lockhart Road Wanchai Hong Kong +852 2386 6326 info@quooker.hk www.quooker.hk...