Download
Share
Print this page
Quooker COMBI Installation Manual
  1. Manuals
  2. Brands
  3. Quooker Manuals
  4. Plumbing Product
  5. COMBI
  6. Installation manual

Quooker COMBI Installation Manual

Hide thumbs Also See for COMBI:

Advertisement

Quick Links

Download this manual
Installation guide COMBI
Before installing read this guide first

Advertisement

loading

Related Manuals for Quooker COMBI

Summary of Contents for Quooker COMBI

  • Page 1 Installation guide COMBI Before installing read this guide first...
  • Page 2 In addition to boiling water, the Quooker COMBI also supplies instant hot water. The COMBI supplies hot water by mixing boiling water from the Quooker tank with cold water from the water mains inside the mixing valve. A thermostatic control element inside the valve keeps the outgoing water temperature constant.
  • Page 3 The fastest way to do this is as follows: turn off the Quooker, but leave the plug in the socket. Then open the boiling-water tap and turn it off once the water runs cold. You can find a more detailed explanation for disconnecting the tank in chapter E.

  • Page 4: Declaration Of Conformity

    Declaration of conformity Quooker Nederland B.V., Staalstraat 13, 2984 AJ Ridderkerk (The Netherlands) herewith declares, on our own responsibility, that the products Quooker COMBI and Quooker COMBI+ are in accordance with the conditions of the following directives: - 2014/35/EU Low Voltage Directive (LVD)

  • Page 5: Technical Specifications

    Technical specifications Tank COMBI Voltage 230 V Wattage* 2200 W Capacity 7 litres Heating-up time* 20 minutes Standby power consumption* 10 W Tank height 48 cm Tank diameter 20 cm Min. mains pressure 200 kPa (2 bar) Max. mains pressure 600 kPa (6 bar) Max.
  • Page 6 Contents of the pack 1. - Nordic single tap, packing ring, centring ring, steel ring, brass sink nut and two screws - or Fusion tap, packing ring, brass fixing plate, fixing nut, white tap support (for thin work tops) and two inlet hose screens - or Flex tap, hoses, fibre washer(s), steel washer, screw ring with two screws, coupling with boiling water hose, white tap support, two inlet hose screens and quick-release tool.
  • Page 7 2. COMBI tank 3. T-joint, inlet hose screens and fibre washer 4. Isolation valve with filter 6. Mixing valve and check valve...
  • Page 8 Overview of Nordic single tap installation It is recommended that you install the Quooker in the following order: A. Drlling hole B1. Fitting Nordic single tap C. Connecting water D. Connecting tank Note: Bear in mind that the tank, mixing valve and socket must remain accessible for servicing.
  • Page 9 Overview of Nordic single tap installation It is recommended that you install the Quooker in the following order: A. Drlling hole B2. Fitting Fusion tap C. Connecting water D. Connecting tank Note: Bear in mind that the tank, mixing valve and socket must remain accessible for servicing.
  • Page 10 Overview of Flex tap installation It is recommended that you install the Quooker in the following order: A. Drlling hole B3. Fitting Flex tap C. Connecting water D. Connecting tank Note: Bear in mind that the tank, mixing valve and socket must remain accessible for servicing.
  • Page 11 Drilling hole • Note: The tap hole for the Nordic single tap should be 32 mm in diameter. The Fusion and Flex tap hole should be 35 mm in diameter. • The Nordic single tap should ideally be positioned at the corner of the sink to enable use above the sink or the work top.
  • Page 12 Fitting Nordic single tap • The total length of the hose between the boiling-water tap and tank is only 70 cm. The tank must therefore be fitted close to the tap. Extension hoses are available in different lengths but are not normally required. •...
  • Page 13 Screw the fixing nut onto the tap thread. Adjust the position of the tap to ensure that the Quooker logo is facing the user. When the handle is in the cold position, it will be parallel to the edge of the work top.
  • Page 14 Fitting Flex tap • When installing the tank it is necessary to take into account that the Flex tap counterweight must be able to move up and down freely. When the hose is not withdrawn it hangs approximately 40 cm below the work surface. •...
  • Page 15 5. Attach the coupling Click the pull-out hose into the coupling’s quick-release fitting while ensuring that the hose pillar is fully inserted. 6. Fit the mixer water hose Click the mixer water hose into the coupling’s quick-release fitting while ensuring that the hose pillar is fully inserted.

  • Page 16: Connecting Water

    Connecting water • The Quooker operates under mains water pressure and must always be fitted to the water pipe with the supplied inlet valve. • The Nordic single tap, the Fusion tap or de the Flex tap must be installed according to the locally applicable regulations.
  • Page 17 Connecting tank to tap • The Quooker tank is supplied with a UK 3 pin plug and requires a standard 13 amp earthed socket. • The light ring on the boiling-water tap will light up to indicate when the water is being heated inside the tank.
  • Page 18 Then close the tap again. Note: At first, the water is very hot. 3. Isolating Close the main shut-off valve or the isolation valve. Check that the Quooker is depressurized by opening the boiling- water handle again. If it is depressurized, On/off no water should flow out of it.
  • Page 20 Quooker Emirates LLC 15A Street, Showroom 17 Al Joud Center Al Quoz, Dubai (UAE) +971 4 330 3063 info@quooker.ae www.quooker.ae...