Table of Contents
Advertisement
Quick Links
PA26001A01
CT-2600 and CT-2600/E
Rev. 02 5-2009
© Panduit Corp. 2009
PRECAUTIONS AND GENERAL GUIDELINES ............................................................................................. 1
TOOL SPECIFICATIONS ................................................................................................................................ 4
CT-2600 and CT-2600/E TOOLS .................................................................................................................... 4
BATTERY OPERATED CRIMPING TOOLS ................................................................................................... 5
CRIMP DIES AND ACCESSORIES ................................................................................................................ 6
DIE SELECTION AND INSTALLATION ......................................................................................................... 6
TOOL OPERATION ......................................................................................................................................... 7
MAINTENANCE / INSPECTION ...................................................................................................................... 8
Die Closure Inspection ..................................................................................................................................... 9
Storage and Transport ................................................................................................................................... 10
TROUBLESHOOTING ................................................................................................................................... 10
DISCONTINUATION OF USE / DISPOSAL .................................................................................................. 10
USE OF THE BATTERY CARTRIDGE AND CHARGING UNIT .................................................................. 10
Terminations per Battery Charge ................................................................................................................... 11
Website: www.panduit.com
Email: cs@panduit.com
Panduit Corp. • USA Headquarters • Tinley Park, IL
Tel: 888-506-5400, ext. 3255 • Fax: 630-759-7532
EU Website:
www.panduit.com/emea
PANDUIT Europe • EMEA Headquarters
Tel: +31 (0) 546 580 452 • Fax: +31 (0) 546 580 441
EU Email: EMEA-
Toolservicecenter@panduit.com
Advertisement
Table of Contents
Related Manuals for Panduit CT-2600
Summary of Contents for Panduit CT-2600
-
Page 1: Table Of Contents
USE OF THE BATTERY CARTRIDGE AND CHARGING UNIT ..............10 Terminations per Battery Charge ........................11 Website: www.panduit.com Email: cs@panduit.com Panduit Corp. • USA Headquarters • Tinley Park, IL Tel: 888-506-5400, ext. 3255 • Fax: 630-759-7532 EU Website: www.panduit.com/emea PANDUIT Europe • EMEA Headquarters Tel: +31 (0) 546 580 452 •... -
Page 2: Precautions And General Guidelines
This supersedes and voids all previous literature, etc. Safety Safety is essential in the use and maintenance of PANDUIT tools and equipment. This manual and any markings on the tool provide information for avoiding hazards and unsafe practices related to the use or service of this tool. - Page 3 CT-2600 and CT-2600/E WARNING Electric Shock Hazard: This tool is not insulated. When using this unit on or near energized electrical lines, use proper personal protective equipment. Failure to observe this warning could result in severe injury or death. WARNING Wear eye protection when operating or servicing this tool.
- Page 4 Avoid dropping the tool. Extreme shock may damage the hydraulic circuit and result in malfunction of the tool. NOTE: In the interest of higher quality and value, PANDUIT products are continually being improved and updated. Consequently, pictures may vary from the enclosed product.
-
Page 5: Tool Specifications
7,2 V – 18,0 Volt DC for EU Part No.: DC1804F Input: 240 Volt AC, 50~60Hz NOTE: The CT-2600 and CT-2600/E tools can also use the CT-2500BC, CT-2500CHR and CT-2500CHR/E battery cartridge and chargers listed below: CT-2500BC Battery Type: Nickel Cadmium (Ni-Cd) -
Page 6: Important Features Of The Ct-2600 And Ct-2600/Ebattery Operated Crimping Tools
CT-2600 and CT-2600/E IMPORTANT FEATURES OF THE CT-2600 and CT-2600/E BATTERY OPERATED CRIMPING TOOLS • The hydraulic unit incorporates an automatic retraction which returns the ram into its starting position when the maximum force is reached. • The unit is equipped with a special brake which stops the forward motion of the ram/dies when the trigger is released. -
Page 7: Crimp Dies And Accessories
DIES ARE DESIGNED TO PROVIDE THE HIGHEST QUALITY CRIMPING WHEN USED WITH PANDUIT TERMINALS. CONNECTIONS UTILIZING THIS TOOL ARE LISTED PER U.L. 486A AND C.S.A. CERTIFIED ONLY WHEN PANDUIT TERMINALS ARE USED. USE OF ANY OTHER BRAND OF TERMINALS IS NOT RECOMMENDED WITH CD-2600 DIES. -
Page 8: Tool Operation
CT-2600 and CT-2600/E TOOL OPERATION LED Display This tool is equipped with a special circuit board incorporating several important features to inform the user about the current status of the unit. The LED signals in the following cases: SIGNAL DURATION... -
Page 9: Maintenance / Inspection
Daily Maintenance Before Use: Inspect dies for wear or damage such as cracks, gouges, or chips. Inspect the tool for damage or leaks. If damage is detected, contact PANDUIT Tool Division. After Use: Wipe all tool surfaces clean with a damp cloth and mild detergent. -
Page 10: Die Closure Inspection
CT-2600 and CT-2600/E DIE CLOSURE INSPECTION: CT-2600 AND CT-2600/E Die Closure inspection is made by using the GO/NO-GO gaging dimensions listed in Fig. 6. TO PERFORM DIE CLOSURE INSPECTION Clean die and plug gage surfaces. With crimp dies properly installed in crimp head, slowly activate tool until dies bottom under light pressure. -
Page 11: Storage And Transport
Crimping tool battery contacts Reform contacts. Tool is inoperative. damaged. Tool components worn or Return tool to PANDUIT Tool Division. damaged. Oil level is low. Return tool to PANDUIT Tool Division. Dies stop during Pull trigger and hold retract button operation. -
Page 12: Terminations Per Battery Charge
CT-2600 and CT-2600/E Indicator Left LED (Red) Right LED (Multi-color) Color Charging unit ready to operate. Battery defective Charging unit out of order. Battery too hot or too cold. New or unused batteries whose Remove battery. Flashing nominal capacity is not sufficient.
Need help?
Do you have a question about the CT-2600 and is the answer not in the manual?
Questions and answers