REL . 2.09-ENG Safety first, WWW! (Who, Where and When can fly it) The "TRIKE FLASH CRUISER" with Powered Para Gliding (PPG) is the most exciting, least expensive, safest and most accessible form of aviation available! However, it is still...
FLY PRODUCTS presents this lightweight paramotor Trike whose main feature is its great versatility and easy disassembly and assembly The FLASH CRUISER is designed to mount the RAIDER (DOUBLE RIM) paramotor series and, by appropriately drilling the support as indicated below, it also allows the installation of other paramotor models, preferably double rim.
Page 5
TRIKE FLASH CRUISER - USER MANUAL REL . 2.09-ENG Drilling of the motor support If the trike is required to mount a certain type of engine, we provide for the factory preparation for drilling and preparation for the indicated motor housing.
Page 6
TRIKE FLASH CRUISER - USER MANUAL REL . 2.09-ENG At this point you can proceed to the side drilling to insert the special through pin, thickened by the two teflon washers, to lock everything with the butterfly bolt. NOTE: Proceed with drilling by steps: 1 - Drill one side at a time with a metal drill bit Ø...
Page 7
TRIKE FLASH CRUISER - USER MANUAL REL . 2.09-ENG Mounting / Setting of lower supports To mount the paramotor onto the Trike, once it is hooked to the motor support, it is necessary to fix the two teflon supports which are of two sizes:...
Page 9
TRIKE FLASH CRUISER - USER MANUAL REL . 2.09-ENG Assembly instructions: To assemble the trike, start by releasing it from the straps applied after folding: Then lift the cradle and raise the paramotor's coupling support in a vertical position, join...
Page 10
TRIKE FLASH CRUISER - USER MANUAL REL . 2.09-ENG To put the wheels in position after opening them, we suggest that you lay the two pulling cables back, place your feet on them to lock them and push the trike forward...
Page 11
TRIKE FLASH CRUISER - USER MANUAL REL . 2.09-ENG Hook the upper tie rods of the wheels to lock the motor support and the cradle: Start with the right rod locking it with the push-pin and then hook the left...
Page 12
TRIKE FLASH CRUISER - USER MANUAL REL . 2.09-ENG Take-off assistance with or without dashboard (optional): If the “take-off assistance option” is present, simply turn it to the vertical position and then lock it with the special velcro straps: Harness attachment points: For the pilot, the harness of its own paramotor can be used with its own carabiners, or the special harness can be mounted (optional), very light and ergonomic .It's also...
Page 14
REL . 2.09-ENG SINGLE OR TANDEM VERSION Transforming the TRIKE FLASH CRUISER from the single version to the double version is very simple, just move the attachment positions of the harness carabiners and then mount the second harness in the preset attachment positions.
Page 15
TRIKE FLASH CRUISER - USER MANUAL REL . 2.09-ENG TWO-SEAT VERSION: For the DOUBLE-SEAT configuration, the plastic rings for the loops are set in the measurements shown in the figure and their function is as follows: = Hook for the paramotor cage tie strap...
TRIKE FLASH CRUISER - USER MANUAL REL . 2.09-ENG ASSEMBLY CHECK It is essential to completely inspect the assembly of the FLASH TRIKE CRUISER to find and resolve any potential problems before proceeding. The inspection should cover the following elements: ...
NOTE! - An example of a pre-flight checklist is provided below for guidance only, FLY PRODUCTS is not responsible for its use or for its completeness. IT IS HIGHLY RECOMMENDED TO USE AN EXAMPLE OR TO CREATE A CUSTOMIZED ONE, PRINT IT, PLASTIFY IT AND USE IT EVERY TIME YOU FLY.
Page 19
TRIKE FLASH CRUISER - USER MANUAL REL . 2.09-ENG Pre-Flight Checklist Example: Site conditions Current weather Long-range (next few hours) forecast Winds aloft Takeoff/landing direction Obstructions (especially Power lines) Trike Wheels well inflated and fixed ...
Ordinary maintenance Even if the TRIKE FLASH CRUISER don’t need important maintenance, we suggest to proceed every 50 hours of use to an accurate inspection of following items:...
Page 21
Check wear conditions of the harness and all belts. CLEANING Clean the TRIKE FLASH CRUISER with clean water and mild soap. Dust and dirt can be wiped off or removed with mild soap and water. Grease and oil can be removed with a good water-based degreaser.
Major repairs should be performed by a trained service technician, or by FLY PRODUCTS. WARNING!: Repairs to the harness or to any areas subject to solicitation of the TRIKE FLASH CRUISER must be carried out exclusively by an authorized dealer or directly by FLY PRODUCTS. WARRANTY FLY PRODUCTS will warrant their product to be free from defects in materials and workmanship for a period of six (12) months from the date of purchase.