Advertisement
Quick Links
—— Instruction Manual ——
BA832/833/833XL
Portable/Adjustable Basketball Systems
P A R T S L I S T
Item
Qty
Description
A
1
Portable Base and Pole Assembly
B
1
Extension Arm Assembly
C
2
Upper Backboard Support Brackets (BA832/833)
D
2
Lower Backboard Support Brackets (BA832/833)
E
4
Backboard Mounting Angles (BA832/833)
F
8
5/16" X 1" Hex Bolts (BA832/833)
G
12
5/16" Flange Nuts (BA832/833)
H
8
5/16" Flat Washers (BA832/833)
I
1
Height Indicator Labels (attached to base)
Do not release the height adjustment handle or loosen the telescoping pole lockbolt until the system is
completely assembled as the telescoping tubes are under spring tension and may cause damage or injury to
Inspect all contents prior to installation. Report any missing parts to dealer immediately.
Carefully read all instructions before proceeding. Pay special attention to the safety instructions on the next page.
Save this instruction in the event that the manufacturer must be contacted in the future for maintenance
information.
1. This basketball system is shipped partially
preassembled. After removing the system from its
shipping skid open the lower padded front of the
unit by removing the Lock Knob (P) and pulling
forward on the top of the lower pad. Remove the
unassembled parts and hardware. See Figure 1.
2. For BA832/833 open the rear ballast storage
compartment by removing 4 screws. Do not
remove the bottom 2 pivot screws. Pivot rear
cover open and place 12 each 4"x 8"x 16" solid
Concrete CAP Blocks and 3 each 4"x 8"x 8" Solid
Concrete CAP Blocks into the compartment.
Make sure that the weight is evenly distributed.
Reposition the rear cover.
See Layout 1.
Date: 11/27/2018
the assembler.
Rev: 8 B.A.
N.J.C.
Item
Qty
Description
J
1
Acrylic Backboard Hardware (pkg. w/ backboard)
K
1
Backboard (pkg. separately)
L
1
Goal (pkg. separately)
M
1
Goal Mounting Hardware (pkg. separately)
N
4
5/16" X 1 1/2" Carriage Bolt (BA832)
O
1
Locking Pin
P
1
Lock Knob
Q
1
Backboard Mounting H-Frame (BA833XL)
Warning!
Figure 1
File: \pub\ba833
1
Customer Service
(800) 247-7668
P
Ref#: 930306
Advertisement
Related Manuals for Bison BA832
Summary of Contents for Bison BA832
- Page 1 Remove the unassembled parts and hardware. See Figure 1. 2. For BA832/833 open the rear ballast storage compartment by removing 4 screws. Do not remove the bottom 2 pivot screws. Pivot rear cover open and place 12 each 4”x 8”x 16”...
- Page 2 Assembly (B) using the 5/16”X 1” Hex Bolts (F), 5/16” Flat Washers (H) and the 5/16” Flange Nuts (G). Do not tighten at this time. For Model BA832 only requires the Upper Backboard Supports (C), discard Lower Backboard Supports (D).
- Page 3 Figure 2 Figure 3 8. On BA832 systems attach 2 Backboard Mounting Angles (E) to the Backboard (K) using 5/16 x 1 1/2” Carriage Bolts (N), 5/16” Flat Washers (H) and 5/16” Flange Nuts (G). On BA833 systems attach the 4 Backboard Mounting Angles (E) to the Backboard (K) using the Acrylic Backboard Hardware (J).
- Page 4 Warning! Never use the backboard to push or pull the system as unwarranted backboard breakage will likely occur. Knob (P) . See Figure 1 14. For storage or transport through a normal 78” tall double doorway: remove the Locking Pin (O) then pivot the extension arm, backboard and goal downwards.