Related Manuals for Omcan VP-NL-0040-MS
Summary of Contents for Omcan VP-NL-0040-MS
- Page 1 Vacuum Packaging Machine Model VP-NL-0040-MS Item 42924 Instruction Manual Revised - 09/01/2021 Toll Free: 1-800-465-0234 Fax: 905-607-0234 Email: service@omcan.com www.omcan.com...
-
Page 2: Table Of Contents
Table of Contents Model VP-NL-0040-MS Section Page General Information --------------------------------------------------------------------------- 3 - 4 Safety and Warranty --------------------------------------------------------------------------- 4 - 6 Technical Specifications -------------------------------------------------------------------------- 7 Installation --------------------------------------------------------------------------------------- 7 - 8 Operation --------------------------------------------------------------------------------------- 8 - 15 Maintenance --------------------------------------------------------------------------------- 16 - 20 Troubleshooting... -
Page 3: General Information
If the package has suffered rough handling, bumps or damage (visible or concealed), please note it on the bill of lading before accepting the delivery and contact Omcan within 24 hours, so we may initiate a claim with the carrier. A detailed report on the extent of the damage caused to the machine must be filled out within three days, from the delivery date shown in the shipping documents. -
Page 4: Safety And Warranty
Si el paquete ha sufrido un manejo de poco cuidado, golpes o daños (visible o oculto) por favor anote en la factura antes de aceptar la entrega y contacte Omcan dentro de las 24 horas, de modo que podamos iniciar una reclamación con la compañia. - Page 5 Safety and Warranty The owner of the machine is fully responsible at all times for the adherence to the locally applicable safety regulations and guidelines. Obey all safety instructions and guidelines as provided in this manual. USER MANUAL • Every user of the machine should be familiar with the contents of this manual and follow its instructions carefully.
- Page 6 1 YEAR PARTS AND LABOUR WARRANTY Within the warranty period, contact Omcan Inc. at 1-800-465-0234 to schedule an Omcan authorized service technician to repair the equipment locally. Unauthorized maintenance will void the warranty. Warranty covers electrical and part failures, not improper use.
-
Page 7: Technical Specifications
Technical Specifications Model VP-NL-0040-MS Seal Length 19.7” / 500mm 10 Programmable Control Busch Vacuum Pump 40 m³ Maximum Product Height 6.9” / 175mm Useful Chamber Size 19.7” x 19.7” / 500 x 500mm Power 4.4 HP / 3.3 kW Electrical... -
Page 8: Installation
Installation • The models with the option Gas/MAP are standard equipped with a compressed air inlet. • Extra sealing pressure is not necessary and not available for the Table-Top models. • Consult your dealer for installation details. • Maximum pressure: 1 bar. •... -
Page 9: Operation
Operation OPTIONAL INSTALLATION OF SOFT-AIR • The Soft-Air feature can also be installed at a later date by ordering the optional soft-air kit. On: Turns the machine on • The machine will start up in the most-recently used program. • The pump of a machine with a transparent cover will start when the cover is closed Off: Turns the machine off •... - Page 10 Operation Adjust program values and turn functions ON/OFF 1. Forward or back; adjusted values are saved right away. 2. Increases or decreases function values. 3. Turns functions ON/OFF; specific functions, like soft-air, clean cut seal, etc., are turned either on or off. 4.
- Page 11 Operation Service Symbol • After reaching a certain number of operating hours or packing cycles, the service symbol will briefly appear on the display when turning on the machine. In addition, the display indicates how many hours or cycles remain before an oil change is required. •...
- Page 12 Operation Clean Cut Controlled (CCC) Seal: on/off, in seconds Soft-Air: on/off, in seconds or mbar (only with sensor) Multi-cycle: on/off, in number of cycles REVIEWING FUNCTION VALUES FOR P1-P9 1. Turn the machine on by pushing the button. 2. The most-recently used program will be indicated. 3.
- Page 13 Operation 6. Select the next function with the button 7. Push the menu button to store all selected values and to return to the Home menu. TURNING OFF MACHINE 1. Turn the machine off by pressing the button. 2. The symbol on the display will start blinking.
- Page 14 Operation initializes sealing function in the cycle. Since air is replaced by water vapor at this point, the oxygen content in the package will be very low. VACUUM PLUS • Only for Ten-Program machines with sensor-based control. • Can be turned on or off in the Settings menu. After reaching a programmed vacuum pressure, the sealing function may be delayed by adding a programmable number of seconds to the vacuum process.
- Page 15 Operation This option minimizes the amount of oxygen in the product. The machine vacuates and gases the package several times in a row, thus flushing air and oxygen from the chamber and the package. This feature is used for delicate products that do not permit vacuation down to 5 mbar, while at the same time requiring a low oxygen content.
-
Page 16: Maintenance
Regular maintenance prevents equipment malfunctions and prolongs the life of the machine. In addition, it optimizes sanitary conditions. • Always have a certified Omcan dealer carry out repair and maintenance activities. WARNING • During maintenance activities, always turn the machine off at the main switch and/or unplug it from the electrical outlet. - Page 17 Maintenance 3. Replace the oil filler cap. 4. After several packing cycles, check the oil level and add as needed. CHANGING OIL 1. Remove the oil drain plug and drain the oil. 2. Replace the drain plug. 3. Remove the oil filler cap. 4.
- Page 18 Maintenance INSTALL THE SEALING WIRE AND TEFLON TAPE AS FOLLOWS: 1. Position the sealing wire across the beam and fasten it on one side with a small bolt. 2. Apply tension on the wire by pulling it with a pair of pliers. 3.
- Page 19 Maintenance 3. Re-tighten the screws after the correct tension has been achieved. 4. Cut the end of the wires flush with the bottom edge of the mounting plate. 5. Apply the Teflon tape smooth and tight over the seal beam without creases. Make sure that the beam is clean and free of grease.
- Page 20 Maintenance REPLACING SILICONE RUBBER SEAL OF COUNTER BEAM The rubber seal is clamped in the counter beam. REPLACE THE COUNTER BEAM SEAL AS FOLLOWS: 1. Pull the old rubber seal from the groove in the counter beam. 2. Clean the groove. 3.
-
Page 21: Troubleshooting
Troubleshooting Fault/Symptom Possible Cause Remedy Machine does not work. The machine is not plugged in. Plug the machine into the electrical outlet. The ground fault safety in the Check the electrical panel. electrical panel has tripped. A fuse in the electrical panel is Check the electrical panel. - Page 22 Troubleshooting The machine does not seal. The bag is not correctly positioned Adjust the bag position. over the sealing beam. The sealing wire is broken. Replace the sealing wire. The thermal safety of the power Wait until the safety resets, which supply was tripped.
-
Page 23: Parts Breakdown
Parts Breakdown Model VP-NL-0040-MS 42924... - Page 24 Parts Breakdown Model VP-NL-0040-MS 42924 Item No. Description Position Item No. Description Position Item No. Description Position Vacuum Chamber 200 Complete for 35230 0010 35258 Blindplug 3/8" MS/VN for 42924 0255 62572 Insert Plate for 42924 0900 42924 Branch Pipe HFE-1 H-2000 Ready for...
- Page 25 Parts Breakdown Model VP-NL-0040-MS 42924 Item No. Description Position Item No. Description Position Item No. Description Position 35317 Earth Terminal PE 6-10 for 42924 2130 35343 Silicon Holder for 42924 3055 35370 Fixed Castor STST. for 42924 4040 Hexagon Screw M8x16 DIN933 A2...
-
Page 26: Electrical Schematics
Electrical Schematics Model VP-NL-0040-MS 42924... -
Page 27: Warranty Registration
Warranty Registration Thank you for purchasing an Omcan product. To register your warranty for this product, complete the information below, tear off the card at the perforation and then send to the address specified below. You can also register online by visiting: Merci d’avoir acheté... - Page 28 Since 1951 Omcan has grown to become a leading distributor of equipment and supplies to the North American food service industry. Our success over these many years can be attributed to our commitment to strengthen and develop new and existing relationships with our valued customers and manufacturers.