Advertisement
112. Entering the P1 Button address.
The P1 button is coded by default with address
100; if you want to change it, you must:
enter the programming mode following
the instructions described in "Entering the
programming mode";
enter code 112 and press P1; you hear a con-
firmation tone and the red LED start flashing;
dial the address you want to assign to P1.
Extensions must be coded with numbers from
001 to 200;
press P1; you hear a confirmation tone and
the red LED go back ON without flashing;
continue by entering the code of a new pro-
gramming or exit the programming mode by
moving the jumper J6 to position 1-2.
113. Entering the P2 Button address.
The P2 button is coded by default with address
101; if you want to change it, you must:
enter the programming mode following
the instructions described in "Entering the
programming mode";
enter code 113 and press P1; you hear a con-
firmation tone and the red LED start flashing;
dial the address you want to assign to P2.
Extensions must be coded with numbers from
001 to 200;
continue by entering the code of a new pro-
gramming or exit the programming mode by
moving the jumper J6 to position 1-2.
114. Unlocking time.
To change the lock release time (max. 10
seconds), you must:
enter the programming mode following
the instructions described in "Entering the
programming mode";
enter code 114 and press P1; you hear a con-
firmation tone and the red LED start flashing;
dial the number of seconds you want the door
lock is released (3 digits from 001 to 010);
press P1; you hear a confirmation tone and
the red LED go back ON without flashing;
continue by entering the code of a new pro-
gramming or exit the programming mode by
moving the jumper J6 to position 1-2.
121. Enable/disable the calling tone.
To enable or disable the calling tone on the
AD2101AGL, you must:
enter the programming mode following
the instructions described in "Entering the
programming mode";
enter code 121 and press P1; you hear a con-
firmation tone and the red LED start flashing;
enter code 004 to disable the tone or 000 to
enable the tone;
press P1; you hear a confirmation tone and
the red LED go back ON without flashing;
continue by entering the code of a new pro-
gramming or exit the programming mode by
moving the jumper J6 to position 1-2.
142. Operations with main or secondary door
keeper exchangers.
The following settings are necessary if in the
system are installed main and/or secondary
door keeper exchangers.
To make the programming you must:
enter the programming mode following
the instructions described in "Entering the
programming mode";
enter code 142 and press P1; you hear a con-
firmation tone and the red LED start flashing;
enter address 201 if the door station operates
with 1 or more main door keeper exchangers
or address 210 if the door station operates
with 1 or more secondary door keeper ex-
changers;
press P1; you hear a confirmation tone and
the red LED go back ON without flashing;
continue by entering the code of a new pro-
gramming or exit the programming mode by
moving the jumper J6 to position 1-2.
151-158. Additional cameras addrresses.
During the conversation it is possible to swi-
tch the image to up to 8 additional auxiliary
cameras connected to VM2521 modulators.
The addresses (231-253) that the modulators
associate with the cameras must be stored in
AD2101AGL, the procedure below must be
repeated for all the 8 cameras:
enter the programming mode following
the instructions described in "Entering the
programming mode";
enter code from 151 (first camera) to 158
(last camera) and press P1; you hear a con-
firmation tone and the red LED start flashing
enter the address with codes from 231 to 253
press P1; you hear a confirmation tone and
the red LED go back ON without flashing;
continue by entering the code of a new pro-
gramming or exit the programming mode by
moving the jumper J6 to position 1-2.
159. Main camera.
It is possible to choose the camera from which
the AD2101AGL starts scanning from one of
those previously stored:
enter the programming mode following
the instructions described in "Entering the
programming mode";
enter code 159 and press P1; you hear a con-
firmation tone and the red LED start flashing;
dial the 3 digits of the address (digits 231
to 253) of one of the 8 cameras previously
stored. If 255 is entered, scanning starts from
the camera on board the AD2101AGL (i.e.
blue screen);
press P1; you hear a confirmation tone and
the red LED go back ON without flashing;
continue by entering the code of a new pro-
gramming or exit the programming mode by
moving the jumper J6 to position 1-2.
.
000. Restore default settings.
Once entered in the programming mode, you
must:
dial 000 following the instructions contained
in "entering codes or addresses";
press P1; you hear a confirmation tone and
the red LED start flashing;
dial 123 following the instructions in "entering
codes or addresses";
press P1; you hear a confirmation tone and
the white LEDs of the camera start flashing;
exit the programming mode moving the jumper
J6 from 2-3 to position 1-2.
PROGRAMMATIONS
FR
Pour effectuer la programmation, il est
nécessaire de télécharger l'application "DUO
System" (disponible pour iOS et Android),
connecter le programmateur PGR2991BT au
système et connecter votre smartphone ou
tablette via Bluetooth. Alternativement, vous
pouvez procéder en agissant manuellement sur
le AD2101AGL. Il est nécessaire de procéder
comme suit
:
Programmations d'usine
- Adresse Poste de Rue = 231
- Adresse associée au poussoir P1 = 100
- Adresse associée au poussoir P1 = 101
- Durée d'activation de la gâche = 1 seconde
- Tonè de libre = abilitée
2-3
Mode de
programmation
3
2
1
J6
3
2
1
J6
1-2
Mode de
fonctionnement
V M
S2
S1 LP LP
Entrer en mode de programmation
Enlever la plaque de rue.
Déplacer le pontet J6 de la position 1-2 sur
2-3; on entend une tonalité de programmation
et la led rouge (R) s'allume.
J6
Quitter le mode de programmation
Pour quitter le mode de programmation, il faut
nécessairement repositionner le pontet J6 de
la position 2-3 sur la position 1-2.
Utiliser les boutons-poussoirs
Pour saisir les adresses et les codes, utiliser
les boutons-poussoirs "P1" et "P2".
P1: La pression de ce bouton-poussoir permet
de confirmer la saisie d'un code ou de
passer à une phase de programmation
successive.
P2: La pression de ce bouton-poussoir permet
d'augmenter la valeur du chiffre à saisir.
Appuyer sur le bouton pour autant de fois
que le chiffre que l'on veut saisir (chiffre 1
= 1 pression; chiffre 9 = 9 pressions; chiffre
0 = 10 pressions sur le bouton "P2")
La pression du bouton-poussoir "P2" est
confirmée par une tonalité émise par le haut-
parleur.
Saisir des codes ou des adresses
- Les codes et/ou les adresses à mémoriser
doivent toujours être composés de trois chiffress
(centaines, dizaines et unités); les codes et/
ou les adresses composés uniquement de
dizaines et d'unités doivent être complétés
S+
S- LP LP
PB GN
P1
P2
J6
R
3
2
1
J6
PB GN
S+
S- LP LP
J1
Pn
P1
J6
poussoir P1
poussoir P2
- 8 -
Mi 2512
Advertisement
